Page 1
MARCHING TENOR DRUM STAND
MTS-3000
Congratulations on your purchase!
To get optimum performance of your MTS-3000 Marching Tenor Drum Stand,
please read this Instruction Manual before playing.
Instruction Manual
Top Section
Base Section
Page 2
Fig.2
Fig.3
Fig.4
Fig.5
Die-Cast Joint
Movable Leg
Lower Bracket
Rubber Tip
Wing Nut
Wing Nut
Stable Leg
Stopper
Upper
Bracket
Wing Bolt
Base Section Assembly (Fig.1)
a) Using on Flat Surface (As shown in Fig. 2)
1. Loosen the Wing Nuts on the
Stoppers of the Stable Legs.
2. Slide the Stoppers to the end
of the Legs to the Rubber Tip,
and tighten the Wing Nuts.
3. Loosen the Wing Bolt on the
Upper Bracket of the Movable
Leg.
4. Slide the Upper Bracket up
and adjust the position until
the base stands straight up,
and tighten the Wing Bolt.
Top Section Assembly (Fig.5)
1. Loosen the Wing Nut of the Die-Cast Joint of the Base.
2. Insert the top section as shown, and tighten the Wing Nut
and the Key Bolt on the Stop Lock.
3. Set the Stability Arm as shown, and tighten the Wing
Bolt.
b) Using on Uneven Surface (As shown in Fig. 3)
1. Loosen the Wing Nuts on the
Stoppers of the Stable Legs.
2. Slide the Stoppers to the end
of the Legs to the Rubber Tip,
and tighten the Wing Nuts.
3. Loosen the Wing Bolts on the
Upper and Lower Bracket of
the Movable Leg.
4. Slide the Upper Bracket to the
top of the pipe, and tighten the
Wing Bolt.
5. Slide the Lower Bracket and
adjust the position until the
base stands straight up, and
tighten the Wing Bolt.
Fig.1
Note
If the distance between the Rubber
Tip of the Movable Leg and the
center of the pipe becomes shorter
than 30 cm, slide both the Upper
and Lower Bracket and adjust their
positions. Make sure to adjust the
position so that the base stands
straight up. (Fig. 4)
Note
・Do not set the Stability Arm for the Trio set-up.
・For height adjustment, loosen the Wing Bolt on the Die-Cast Joint
and the Key Bolt on the Stop Lock, and slide the Top Section.
Tighten the Wing Bolt on the Die-Cast Joint and the Key Bolt on
the Stop Lock when desired height is achieved. Do NOT make
height adjustment with the Tenor Drum mounted on the stand.
Die-Cast Joint
Wing Nut
Key Bolt
Stability Arm
Receiver
Tenor Arm
Wing Bolt
Stop Lever
Slide Shaft
Stop Lock
Page 3
Fig.6
Fig.7 Fig.8
Setting the Tenor Drum (Fig.6)
1. Spread the Tenor Arms as shown.
2. Loosen the Wing Bolt on the Stability Arm, and extend
the Arm to the position where the Receiver does not
touch the Tenor Drum.
3. Insert the Tenor Arms into the J-Rod Brackets of the Back
Bar on the Tenor Drum.
4. Adjust the position of the Receiver so that it is placed
under the central Tenor Drum Spacer, and tighten the
Wing Bolt on the Stability Arm. (Fig.7)
Note
・The tenor drum can be tilted by adjusting the height of the Slide
Shaft. Press the Stop Lever to decrease height of the slide shaft.
To increase height of the slide shaft, push up underneath it with
your fingers. (Fig.8) DO NOT make adjustments with the tenor
drums mounted on the stand.
Stability Arm
Receiver
Tenor Arm
Wing Bolt
Stop Lever
Slide Shaft
・This stand is designed to be used with Tenor Drums with CX
or MX style back-bar. Tenor Drums other than these could
result in unstable settings and should not be used.
Note
・ Do not use on unstable or sloped surfaces, as it could
cause the stand to fall, resulting in damage and/or
injury.
・ Do not move the stand with the tenor drums mounted
on the stand.
・ Before use, check all Stop Locks to assure they are
properly positioned and secured.
・ Do not mount the Tenor Drums (except the Trio
set-up) without the Stability Arm. The Tenor Drums
could become unstable and could cause damage
and/or injury.
・ Periodically check all Wing Nuts, Wing Bolts and the
nuts under the Tenor Arm to assure they are tightened
securely.
・ When making adjustments, support and control the
parts being adjusted to prevent them from falling or
pinching fingers that may be in the way.
・ When folding the legs, be careful not to pinch your
fingers between the leg and the stand.
・ When handling tubular hardware, do not put your
fingers into the tubes top prevent injury to your
fingers.
CAUTION
http://www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-1406-
Loading...