PEARL HI-HAT STAND
H-830/H-930
Instruction Manual
Congratulations on your purchase!
To get optimum performance from your H-830 / H-930 Hi-Hat Stand,
please read this Instruction Manual before playing.
Hi-Hat Clutch
Pull Rod
Hi-Hat Cup
Upper Tube
StopLock
Wing Nut
Die-Cast Joint
Base
Wing Bolt
Spring Tension Adjustment Dial
Rubber Tip
Footboard
Radius Rod
(Illust：H-930)
Footboard Attachment / Base Assembly
Lay the Base Assembly horizontally on the floor. Squeeze
the Radius Rods together and insert the ends into the
Holes in the Support Casting as shown (Fig.1). Loosen the
Wing Bolt and open the legs. Stand the Base Assembly
vertically and adjust the legs to form a stable tripod. The
Support Casting should be flat on the floor. Tighten the
Wing Bolt to secure.
Wing Bolt
Upper Section Assembly
Remove the Pull Rod from the
Upper Tube. Loosen the Wing
Bolt on the Hi-Hat Clutch and
remove it from the Pull Rod.
Thread the Pull Rod into the
Connector inside the Die-Cast
Joint of the Base as shown and
tighten securely (Fig.3, 3-A).
Fig. 3-A
Pull Rod
Wing Bolt
Hi-Hat Clutch
Upper Tube
Support Casting
Hole
Radius Rod
Note
The legs can be swivelled to accommodate multi-pedal
set-ups. Loosen the Wing Bolt and swivel the legs to the
desired position (Fig. 2).
Wing Bolt
Fig. 1
Pull Rod
Connector
Pull Rod
Die-Cast Joint
BASE
Next, loosen the Key Bolt on
the StopLock* and insert the
Upper Tube into the Die-Cast
Joint. Adjust the height of the
Upper Tube to your preference
and tighten the Wing Nut/Wing
Bolt** on the Die-Cast Joint.
Slide the StopLock against the
Die-Cast Joint and tighten the
Key Bolt (Fig.4).
Wing Nut
H-830 is not equipped with a StopLock.
The H-930 is equipped with a Wing Nut on the Die-Cast
Joint, and the H-830 is equipped with a Wing Bolt.
Upper Tube
StopLock
Die-Cast Joint
Fig. 3
Fig. 4
Fig. 2
CAUTION
Make sure that the tripod is stable and the Wing Bolt is
securely tightened before playing.
Attaching the Hi-Hat Cymbals
Please have your Hi-Hat Cymbals ready. First, place the
Bottom Cymbal on the Hi-Hat Cup as shown (Fig.5).
Remove the Bottom Lock Nut and one of the Felt Washers
from the Hi-Hat Clutch. Insert the Hi-Hat Clutch into the Top
Cymbal and replace the Felt Washer and the Bottom Lock
Nut as shown (Fig.5-A). Insert the Pull Rod through the
Hi-Hat Clutch as shown (Fig. 5). The distance between the
Top and Bottom Cymbals can be adjusted by stepping on
the Footboard. Tighten the Wing Bolt on the Hi-Hat Clutch
when the desired spacing is achieved.
Fig. 5-A
Felt
Washers
Bottom
Lock Nut
Wing
Bolt
Top Cymbal
Hi-Hat Cup
Upper Tube
Hi-Hat Clutch
Top Cymbal
Pull Rod
Bottom Cymbal
Fig. 5
Hi-Hat Cup Tilt Adjustment
The tilt on the Hi-Hat Cup can
be adjusted by turning the
Knob. Tilting the Hi-Hat Cup
prevents “air lock” between
the cymbals.
Knob
CAUTION
The Base Tube is secured to the Support Casing with an Allen
Screw. Periodically check it for tightness and if it's loose,
tighten it with an Allen wrench to restore stability (Fig.8).
Base Tube
Allen Screw
Support Casting
Fig. 8
Periodically lightly lube external moving parts such as the
Chain, Wing Nuts, Wing Bolts, Key Bolts and the hinge on the
Footboard.
Fig. 6
Spring Tension Adjustment (ONLY on H-930)
The Spring Tension can be adjusted by turning the Spring
Tension Adjustment Dial on the Base. Turn it clockwise to
make it lighter and counterclockwise to make it stronger.
StrongLight
Spring Tension
Adjustment Dial
Fig. 7
Products and specifications are subject to change without notice.
http: //www.pearldrum.com
Printed in China
-1412-
Loading...