Pearl H-1050 Instruction Manual

Hi-Hat Clutch

Felt Washer

Hi-Hat Cup

TractionPlate
w/ Traction Grips

Reversible Spiked / Rubber

Tipped Feet

Spring Tension Adjustment Dial

Base

Upper Tube

Upper Pull Rod

Die-Cast Joint

StopLock

Wing Bolt

Adjustment Ring
(for Footboard Angle)

Toe Stopper

Radius Rod

H-1050

Instruction Manual

Congratulations on your purchase!

To get optimum performance of your H-1050 Hi-Hat Stand,

please read this Instruction Manual before playing.

PEARL HI-HAT STAND

Footboard Attachment

Squeeze the Radius Rods together and insert the ends into
the Holes in the Support Casting as shown. Loosen the
Wing Bolt and spread the legs. Stand the hi-hat base
vertically and set the bottom of the Support Casting
squarely on the floor to form a solid tripod. Tighten the
Wing Bolt to secure the Base section (Fig.1).

Swivel Leg Adjustment

The legs can be swiveled to the desired position. To do so,
loosen the Wing Bolt and adjust the position of the legs.
When set, make sure the tripod is stable and tighten the
Wing Bolt (Fig.2).

Fig. 2

Radius Rod

Support Casting

Wing Bolt

Hole

Fig. 1

Wing Bolt

Tip

Test the stability of the hi-hat before playing. Readjust the legs as
necessary to achieve a stable tripod before proceeding.

Upper Section Assembly

Thread the Upper Pull Rod into the Connector inside the
Die Cast Joint as shown in (Fig.3-A) and tighten securely.
Insert the Upper Tube into the Die Cast Joint and set the
height to your preference then tighten the Wing Nut. Set the
Stop Lock by loosening the Key Bolt and sliding the Stop
Lock against the Die Cast Joint, then retighten the Key Bolt.
Thread the Lower Hi-Hat Cymbal through the Upper Pull
Rod and place it on the Hi-Hat Cup. Assemble the Top
Hi-Hat Cymbal and the Hi-Hat Clutch as shown in (Fig.3-B).
Tighten the Key Bolt on the Bottom Nut (Fig.3-C) to prevent
it from loosening during performance. Mount the Clutch with
the Top Hi-Hat Cymbal attached to the Upper Pull Rod.
Adjust the distance between the top and bottom cymbals to
your preference then secure the Clutch by tightening the
Wing Bolt.

Fig. 3-B

Fig. 3-C

Fig. 3-A

Top Cymbal

Bottom Nut

Felt

Washers

Upper Tube

Upper Pull Rod

Stop Lock

Top Hi-Hat Cymbal

Lower Hi-Hat Cymbal

Hi-Hat Clutch

Die-Cast Joint

Wing Nut

Hi-Hat Cup

Bottom Nut

Connector

Upper
Pull Rod

Attaching the

Upper Pull Rod

Wing Bolt

Die-Cast Joint

StrongLight

Fig. 5

Fig. 6

Hi-Hat Cup Tilt Adjustment

Turn the Knurled Knob to tilt the
bottom cymbal to help prevent
"air lock" between the cymbals
(Fig.4).

Spring Tension Adjustment

The spring tension can be
adjusted quickly and
precisely by turning the
Spring Tension Dial. This
innovative system features
extended tension range
and click-stops for
slip-proof performance
under the most demanding
playing conditions (Fig.5).

Footboard Angle Adjustment

To change the footboard
angle, loosen the Key Bolt
and turn the Adjustment
Ring. When the desired
angle is achieved.
re-tighten the Key Bolt to
retain this setting (Fig.6).

Fig. 4

Fig. 7

Reversible Spiked / Rubber Tipped Feet

For maximum slip prevention, the Spike Tip should be used.
Loosen the Key Bolt until the Spike is easily turned then
rotate the Spike downward. Tighten the Key Bolt to lock the
Spike (Fig.10).

Fig. 10

Key Bolt

Adjustment Ring

Knurled Knob

Upper Pivot

Lower Pivot

Key Bolt

Spike Tip

Tip

The Spikes are sharp and can cause serious personal or property
injury. To prevent mishaps, use extreme care when handling the
stand especially when the Spike Tips are exposed. A rug or carpet
should be used to protect floor surfaces whenever the Spikes are
used.

Tip

When changing the footboard
angle, make sure that the
Upper and Lower Pivots are
parallel as shown in (Fig. 7)

Fig. 9

Fig. 8

Traction Grip and Traction Plate Adjustment

The Traction Grip dots can be totally removed or inserted
as needed to custom tailor the amount of traction for your
personal playing style. To remove the Traction Grip dots,
loosen the Allen Screws holding the Traction Plate with the
provided hexagonal wrench and remove the Traction Plate
from the footboard (Fig.8). The Traction Plate is also
reversible to provide just the right amount of grip at either
the front or rear of the footboard (Fig.9).

Traction Plate

Traction Grip dots

CAUTION

When putting the Traction Plate back, finger-tighten the four screws
to prevent cross-threading; then tighten the screws securely. Do not
use the Pedal without the Traction Plate mounted. It could cause
injury to your foot.

Maintenance

The Base Tube is secured to the Support Casting with an
Allen screw. In the event the Base Tube becomes loose,
tighten the Allen screw with the provided hexagonal wrench
to restore stability.

http://www.pearldrum.com

Products and specifications are subject to change without notice.

Printed in China

-1601-

Support Casting

Allen Screw

CAUTION

Periodically check all Allen Screws for tightness and
tighten them with the provided hexagonal wrench as
needed.

Periodically lightly lube external moving parts such as
the Chain, Wing Nuts, Wing Bolts, Key Bolts, and
Footboard Hinge to achieve optimum performance
from your stand.

To maximize traction of the rubber mat beneath the
heel plate, keep it clean and dust free using a damp
cotton towel.