Page 1
Instruction Manual
Congratulations on your purchase! To get optimum performance of your E-PRO Live Drums,
please read this Instruction Manual before playing.
PEARL
http: //www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in Taiwan
-1003-
sample
Page 2
- 1 - - 2 -
SET-UP EXAMPLE (FRONT) SET-UP EXAMPLE (BACK)
A Bass Drum
B Snare Stand
C Hi-Hat Controller
D Drum Rack
E Hi-Hat Holder
F Cable Harness
G r.e.d.box Module
H 12” Hi-Hat Cymbal
I 13” Crash Cymbal
J Snare Drum
K Cymbal Holder
W 12” Rubber Hi-Hat Cymbal
X 12” Rubber Crash Cymbal
Y 14” Rubber Ride Cymbal
L 10” Tom Tom
M 12” Tom Tom
N 16” Ride Cymbal
O Velcro Strap
P 14” Tom Tom
Q Drum Pedal (Optional)
R Tru-Trac Bass Drumhead
S 14” Tru-Trac Drumhead
T 12” Tru-Trac Drumhead
U 10” Tru-Trac Drumhead
V 14” Tru-Trac Drumhead
A
P
B
V
E
R
C
C
Q
B
D
D
E
G F
F
H
J
LM
U T
I N
W X Y
G
H
N
I
O
K
S
sample
Page 3
- 3 - - 4 -
H-1 D-1 D-2 D-3 D-4
D-5 D-6
D-9
D-7
D-8
H-2
H-5
H-3
H-6
H-4
H-7
D-11D-10
D-12 D-13 D-14
COMPONENTS / HARDWARE CARTON COMPONENTS / DRUM CARTON
H-1 Drum Rack (x1) Includes : PC-8 Pipe Clamps (4)
H-2 S-790 (x1) Snare Stand
H-3 CH-80E (x2) Cymbal Holders
H-4 CLH-80E (x1) Hi-Hat Holder
H-5 UX-80 (x1) Universal Clamp
H-6 TH-900S (x3) Tom Holders
H-7 NP-485 (x12) Velcro Straps
D-1 EDD1445S (x1) 14"x 4.5" SD
D-2 EDD1065T (x1) 10"x 6.5" TT
D-3 EDD1207T (x1) 12"x 7" TT
D-4 EDD1408T (x1) 14"x 8" TT
D-5 EDD2012B (x1) 20"x 12"BD
D-6 EBC-20F (x1) BD Front Side Head
D-7 EBC-20EB (x1) BD Batter Side Head
D-8 RIM-20RB (x2) BD Hoop
D-9 NP-1 (x1) Rubber Hoop Protector
D-10 CW-80 / T-066X (x16) BD Claws, BD Tension Rods,
W7/32 x 110mm
D-11 NP-488L (x1) BD Cushion
D-12 CH-1JB (x5) Jack Box Cable
D-13 K-050 (x1) Drum Key
D-14 Hex Wrench (x1) (5mm)
sample
Page 4
- 5 - - 6 -
E-1 B-1
B-5
B-2 B-3 B-4
E-4
E-7 E-8
E-5 E-6
E-2 E-3
E-1 TTP-14 (x2) 14” Tru-Trac Drumheads
E-2 TTP-10 (x1) 10” Tru-Trac Drumhead
E-3 TTP-12 (x1) 12” Tru-Trac Drumhead
E-4 TTP-B (x1) Tru-Trac Bass Drumhead
E-5 EHH-1 (x1) HH Controller
E-6 CH-10 (x1) Cable Harness
E-7 RDM-20M/M (x1) r.e.d.box Module & Mounting Bracket
E-8 Power Supply (x1)
B-1 ECC-12S (x1) 12” Brass HH Cymbal
B-2 ECC-12B (x1) 12” Plastic Bottom HH
B-3 ECC-13D (x1) 13” Brass Crash Cymbal
B-4 ECC-16T (x1) 16” Brass Ride Cymbal
B-5 CM-1 (x2) Cymbal Mount
COMPONENTS / ELECTRONICS CARTON COMPONENTS / BRASS CYMBAL CARTON
P-1 P-2 P-3 P-4
P-1 EPC-12S (x1) 12” Rubber HH Cymbal
P-2 EPC-12D (x1) 12” Rubber Crash Cymbal
P-3 EPC-14T (x1) 14” Rubber Ride Cymbal
P-4 CM-1 (x2) Cymbal Mount
COMPONENT / RUBBER CYMBAL CARTON
sample
Page 5
- 7 - - 8 -
SETTING UP THE RACK
Note
*Remove all components from the Pipe Clamps and Pipe
Brackets before making adjustments to the height of the
rackor position of the Pipe Clamps.
*Securely tighten (don’t over-tighten) all handle bolts on the
Pipe Clamps and Pipe Bracke ts when the positions are
finalized.
1. Locate the two “long” legs (each has a PCL-100 Pipe
Bracket attached) and connect one to each end of the
Front Bar (it has a Pearl logo badge) as shown (Fig. 1).
Orient the Front Bar so that the “Pearl” logo on the
clamps is facing right-side up for opti mum stability
(Fig. 1-A).
2. Connect a Side Bar to the left “long” leg as shown (Fig.
2) with the “Pearl” logo on the clamps facing right-side
up for optimum stability (Fig.1-A). Locate the “shor t”
leg with a PCL-100 Pipe Bracket attached and connect
it to the other end of the Side Bar as shown.
3. Connect the last Side Bar to the right “long” leg as
shown (Fig. 3) with the “Pearl” logo on the clamps
facing right-side up for optimum stability (Fig. 1-A).
Connect the remaining “short” leg to the other end of
the Side Bar as shown.
4. Adjust the height of the Front and Side Bars to your
preference and make sure that all bars are levelled.
5. Attach two Pipe Clamps to the Front Bar and one each
on both Side Bars (Fig. 4 and 4-A).
6. Atta ch the Tom Holders, Cymbal Holders , Hi-Hat
Holder and the Universal Clamp to the Pipe Clamps
and Pipe Bracket as shown below (Fig. 5).
7. Reverse the position of the left and right Side Bars if
you’re left-handed.
Caution
Caution
ASSEMBLYING THE TOMS AND SNARE DRUM
*The bottom head on the Toms and the snare side head on
the Snare Drum are pre-assembled at the factory.
*Tighten the Tension Bolts with only enough tension to hold
the Hoop in place. Using greater tension can damage the
plastic frame of the
Tru-trac Drumheads and void the
warranty.
1. Loosen the Tension Bolts on the batter side of the
drums using the provided Drum Key and remove the
Hoops (Fig. 6).
2. Locate the Tru-trac Drumhead that corresponds to the
diameter of each drum. NOTE: The two 14” Tru-trac
Drumhead are identical and either can be used on the
14” Tom or the Snare Drum.
3. Insert the “L” shaped end of the Jack Box Cable into
the Jack on the underside of the Tru-trac Drumhead
(Fig. 7).
4. Insert the other end of the Jack Box Cable into the
Jack Box inside the shell (Fig. 7).
5. Place the Tru-Trac Drumhead on the shell and reattach
the Hoop with the Tension Bolts (Fig. 8). NOTE: The
Jack Box Cables are short and have only limited reach.
When assembling Toms, align the Tru-Trac logo with
the BT-70 Tom Holder Bracket as shown (Fig. 8-A).
Similarly, when assembling the Snare Drum, align the
Tru-Trac logo with the E-Pro Live Badge.
Long Leg
PCL-100 Pipe Bracket
PCL-100
Pipe Bracket
Short Leg
Fig.1
Fig.1-A
Fig.6
Fig.7
Fig.8
Fig.8-A
Fig.2
Fig.3
Fig.5Fig.4
Fig.4-A
Tesion Bolt
Hoop
Tru-trac Drumhead
Tru-trac Drumhead
Jack Box
Jack Box
Cable
Lug
Tension Bolt
Universal
Clamp
Hi-Hat Holder
Cymbal Holder
Cymbal Holder
Tom Holders
Hoop
BT-70
BT-70
Lug
Lug
Bar
sample
Page 6
- 9 - - 10 -
ASSEMBLYING THE TRU-TRAC BASS DRUMHEAD
1. Unscrew the bolts on the Tru-Trac Bass Drumhead
using the provided Hex wrench and remove the black
steel hoop (Fig. 9).
2. Turn the Tru-Trac Bass Drumhead over and place it on
your hand (Fig. 10).
3. Place the Bass Drum Head over the Tru-Trac Bass
Drumhead as shown making sure that the Guide Posts
on the Tru-Trac Bass Drumhead are inserted into the
corresponding guide holes in the Bass Drum Head
(Fig. 10-A & 10-B).
4. Place the black steel hoop as shown making sure that
the Guide Posts on the Tru-Trac Bass Drumhead are
inserted int o the corresponding guide holes in the
black steel hoop (Fig. 10 & 10-B).
5. Hand tighten the bolts on the Tru-Trac Bass Drumhead
from underneath.
6. Turn the Bass Drum Head over and tighten the bolts
securely using the provided Hex wrench.
ASSEMBLYING THE BASS DRUM
Note
*The Bass Drum Head will be floppy at this point but will
become taut when attached to the shell and tightened.
1. Place the Front Head on to the Bass Drum shell as
shown with the Pearl logo up and square the Pearl logo
(Fig. 11). Place the Bass Drum hoop over the head with
the flat side of the hoop facing down (Fig. 11-A). Hook
a Tension Rod and Claw on the Hoop above each lug
and tighten the Tension Rods using the provided Drum
Key.
2. Turn the drum over and put the Bass Drum Cushion
inside and at the bottom the Bass Drum Shell. Make
sure that the Cushion does n't touch the Jack Bo x
inside the shell
(Fig. 12).
3. Insert the “L” shaped end of the Jack Box Cable into
the Tru-Trac Bass Drumhead as shown (Fig. 13-A) and
insert the other end of the cable into the Jack Box
inside the Bass Drum shell as shown (Fig. 13-A).
4. Place the Batter Side Head onto the Bass Drum shell
with the Tru-Trac Bass Drumhead facing the top of the
Bass Drum as shown (Fig. 14). Place the Bass Drum
Hoop over the head with the flat si de of the hoop
facing down (Fig. 14-A).
5. Hook a Tension Rod and Claw on the Hoop above
each lug and ti ghten the Tension Ro ds using the
provided Drum Key (Fig. 14-A).
6. Attach the Hoop Protector on the batter side hoop
where you attach your pedal.
Fig.9
Fig.12
Fig.11
Fig.11-A
Fig.13-A
Fig.13 Fig.14
Fig.10
Fig.10-B
Top
Bottom
Fig.10-A
Bolt
Bass Drum Cushion
Jack Box Cable
Head
Tesion Rod
Hoop
Claw
Tesion Bolt
Hoop Protector
Hoop
Claw
Washer
Bolt
Guide
Post
Washer
Tru-Trac
Bass Drumhead
Tru-Trac
Bass Drumhead
Black Steel
Hoop
Tru-Trac
Bass Drumhead
Guide Post
Guide Post
Bass Drum Head
Black Steel
Hoop
Black Steel
Hoop
Jack Box
Claw
Hoop
Fig.14-A
Claw
Hoop
sample
Page 7
- 11 - - 12 -
HH CONTROL
6
HI HAT
5
TOM34 TOM24 TOM22 SNARE1 KICK
ON
9V AC
OFF
7
CRASH8 RIDE19 RIDE2/ACC110 ACC211 ACC312 ACC4
MIDI OUT M IDI IN USB AUX IN R
AUX IN L
AUX OUT MAIN OUT
R2
L1
POWER
SETTING THE DRUMS ON THE RACK
BASS DRUM
Position the Bass Drum upright and set the Bass Drum
Spurs as shown with the front of the drum about an inch
off the floor (Fig. 15).
The Bass Drum Spurs have spike tips (for added slip
resistance) that can be exposed by turning the Lock Nut
and Rubber Tip clockwise (Fig. 15).
TOM TOM
Make sure that the Tom Holders and the Pipe Clamps are
securely attached. Attach the Toms to the Tom Holders
and position the height and angles to your preference.
When done, set the tab on the StopLock into the slot in
the Pipe Clamp and Tom Holder Bracket and tighten the
Key Bolts with the provided Drum Key to retain the angle
and height settings (Fig. 16).
SNARE STAND/DRUM
Open the legs of the stand to form a stable tripod and
insert the Top Section into the base.
Open the basket and adjust the Butterfly Nut as needed
to accommodate the snare drum.
Place the snare drum into the basket and tighten the
Butterfl y Nut to ho ld the drum securely ( do not
overtighten) (Fig. 17).
ASSEMBLYING THE r.e.d.box Module
*Use the spikes only on thick carpeted surfaces to prevent
damage to the flooring underneath.
1. At tach the r.e.d.box Mount to the b ottom of the
r.e.d.box as sh own us ing a screwdriver. D o not
overtighten (Fig. 18).
2. Insert the Mount into the Universal Clamp and tighten
the Wing Nut (Fig. 19). Note: Keep the jaws of the
clamp parallel.
3. Adjust the height and angle of the r.e.d. box Module to
your preference.
*Make sure all bolts and nuts are tighten after setting.
Caution
Warning
ASSEMBLYING THE CYMBAL HOLDER
1. Unscrew the Wing Nut on the Cymbal H older and
detach the Felt Washer. Put both aside for now.
2. Attach the Cymbal Mount onto the Cymbal Post and
rotate the Attachment Screw until it's at a right angle to
the Cymbal Holder Tilter as shown (Fig. 20).
3. Tighten the Attachment Screw with the provided Hex
Wrench.
Note
*The Cable Harness has two sides, one bundled together and the other separated.
WIRING THE CABLE HARNESS
1. Each cable is marked with the name of the component it connects to. Take the bundled side and match the cable to
its correcponding jack on the back side of the r.e.d.box (Fig. 21). NOTE: The Ride Cymbal has two Jacks. Make
sure to insert the cables into the correct Jacks
2. Take the separated side and match the cable to its corresponding component.
3. Use the provided Velcro Straps to secure the cables to the rack for a clean look.
Fig.19
Fig.20
Fig.21
Fig.18
Fig.15
Fig.16
Fig.17
Spike
Tom Holder
StopLock
Tom Holder Bracket
StopLock
Pipe Clamp
Butterfly Nut
r.e.d.box
Mount
Universal Clamp
Screw
Cymbal Mount
Cymbal Post
Cymbal Holder tilter
Attacment Screw
Rubber Tip
Lock Nut
Spur
sample
Page 8
- 13 - - 14 -
WIRING AND MOUNTING CRASH/RIDE CYMBALS
1. Locate the Ride and Crash Cymbal and their matching
cables and insert the cables into the corresponding
jacks. Note: The Ride Cymbal has two Jacks. Make
sure to insert the cables into the correct Jacks
(Fig. 22-A).
2. Attach the Cymbal to the Cymbal Mount and attach the
Felt Washer and Wing Nut in the order shown (Fig. 22).
Make sure that the logo on the Cymbal is facing away
from you to get maximum response from the cymbal.
WIRING AND MOUNTING BRASS HI-HAT CYMBAL
1. Unscrew the Wing Nut on t he Hi-Hat Holder and
remove the Felt and Metal Washer s a nd t he
Attachment.
2. Place the Bottom P lastic Cymbal on the Suppor t
Washer as shown. and reattach the Attachment in the
order shown (Fig. 24).
3. Pass the Hi-hat Cable through the hole in the Bottom
Plastic Cymbal as shown (Fig. 24) and plug it into the
Jack under the Brass Hi-hat Cymbal as shown (Fig.
24-A).
4. Assemble the Brass Hi-hat Cymbal, Felt Washer, Metal
Washer, and Wing Nut in the order shown (Fig. 24).
5. Tighten the Wing Nut to your preference.
WIRING AND MOUNTING RUBBER HI-HAT CYMBAL
1. Unscrew the Wing Nut on t he Hi-Hat Holder and
remove the Felt and Metal Washers
2. Arrange the Attachment and Support Washer in the
order shown (Fig. 23).
3. Set the Rubber Hi-hat Cymbal on the Support Washer
and Attachment as shown. Note: Make sure that they fit
securely in the rec ess un der the Rubber Hi-hat
Cymbal. Face the logo on the Hi-hat Cymbal away from
you to get maximum response from the cymbal.
4. Reattach the Felt and Metal Washers and the Wing Nut
in the order shown (Fig. 23) and tighten the Wing Nut
to your preference.
5. Connect the Hi-hat cable into the Hi-hat Cymbal Jack.
Fig.22-A
Fig.24-A
Fig.23
Fig.22
Fig.24
Wing Nut
Wing Nut
Support Washer
Attachment
Jack Box Cable
Cymbal Post
Metal Washer
Felt Washer
Wing Nut
Metal Washer
Felt Washer
Attachment
Support Washer
Cymbal Post
Felt Washer
Jack Box
Note
*The angle of the Hi-Hat Holder can be adjusted with the
gear tilter to your preference.
Note
*The angle of the Hi-Hat Holder can be adjusted with the
gear tilter to your preference.
sample
Page 9
Page 10
Loading...