Page 1
Clip-on Logo
PCL-100
Bracket
PCX-100
Pipe Clamp
Bar
Clamp
Memory Ring
Leg Post
Floor Bar
A A
B B
Instruction Manual
Congratulations on your purchase of the Pearl Drum Rack System.
To get the maximum performance from your Pearl Drum Rack,
please read this Instruction Manual carefully.
PEARL DRUM RACK SYSTEM
DR-503
Three-section Drum Rack
w/Straight Bar
Components
• Straight Bar / 40x40x915mm (36"Long) (3)
• Leg Post / 38.1x840mm (33"Height) (4)
• PCL-100 Bracket (2)
• Floor Bar / 38x38x500mm (20"Long) (4)
• Memory Ring (6)
• PCX-100 Pipe Clamp (4)
• Clip-on Logo (1)
• Drum Key (1)
• Allen Wrench (1)
The DR-503/DR-501/DR-501C/DR-501E/DR-501CE feature our exclusive square bar design for 100% slip-proof
performance. The bars are independently height adjustable and height setting are retained with Memory Ring for quick
and repeatable set-ups. The DR-503 features three sections and is ideal for configurations with all hanging toms. The
DR-501 and DR-5001C feature a bridge-style design and are ideal for smaller kits or percussion set-ups. By adding
DR-501E or DR-501CE Extension units, the DR-503, DR-501, or DR-501C can be expanded to accommodate
additional drums, cymbals, etc. The front legs of the DR-503, DR-501, and DR-501C are equipped with a mounting
bracket for convenient attachment of tom arms and cymbal holders.
Page 2
DR-501C
Bridge-style Drum Rack
w/Curved Bar
PCL-100
Bracket
PCL-100
Bracket
B
C
C
B
Components
• Curved Bar / 40x40x1120mm (44"Long) (1)
• Leg Post / 38.1x840mm (33"Height) (2)
• PCL-100 Bracket (2)
• Floor Bar / 38x38x500mm (20"Long) (2)
• Memory Ring (2)
• PCX-100 Pipe Clamp (2)
• Clip-on Logo (1)
• Drum Key (1)
• Allen Wrench (1)
DR-501E
Extension Unit
w/Straight Bar
Components
• Straight Bar / 40x40x915mm (36"Long) (1)
• Leg Post / 38.1x840mm (33"Height) (1)
• Floor Bar / 38x38x500mm (20"Long) (1)
• Memory Ring (2)
• Drum Key (1)
DR-501CE
Extension Unit
w/Curved Bar
Components
• Curved Bar / 40x40x1120mm (44"Long) (1)
• Leg Post / 38.1x840mm (33"Height) (1)
• Floor Bar / 38x38x500mm (20"Long) (1)
• Memory Ring (2)
• Drum Key (1)
DR-501
Bridge-style Drum Rack
w/Straight Bar
Components
• Straight Bar / 40x40x915mm (36"Long) (1)
• Leg Post / 38.1x840mm (33"Height) (2)
• PCL-100 Bracket (2)
• Floor Bar / 38x38x500mm (20"Long) (2)
• Memory Ring (2)
• PCX-100 Pipe Clamp (2)
• Clip-on Logo (1)
• Drum Key (1)
• Allen Wrench (1)
Page 3
C
A B
Fig. a
Fig. b
Fig. a
Fig. b
Connecting the Leg Post and Floor Bar
For best stability the Floor Bar
should be positioned facing
FORWARD (away from the
player). Insert the tapered end
of the Leg Post into the Floor
Bar as shown. Securely
tighten the Wing Nut and
Knurled Nut (keep the clamp
parallel to the Floor Bar to grip
the Leg Post evenly).
Leg Post
FORWARD
Knurled Nut
Wing Nut
Floor Bar
Clamp
Memory Ring
Remove and relocate here.
Bar
Connecting the Bar and Leg Post
Loosen the key bolt on the Memory Ring. Set the Memory
Ring on the Leg Post at the approximate height where you
want the Bar located. Attach the Clamp at the end of the
Bar around the Leg Post and rest it on the Memory Ring.
Securely tighten the wing nut on the Clamp.
Connecting Extension Units
The DR-501E and DR-501CE come with two Memory
Rings on the Leg Post. Before connecting the
DR-501E/DR-501CE, remove one of the Memory Rings
and attach it to the Leg Post of the existing Drum Rack at
the desired location.
DR-501E/DR-501CE
Allen Wrench
Swivel Bracket
PCL-100
Cap
PCX-100 Pipe Clamp
DR-503, DR-501, and DR501C are equipped with
PCX-100 Pipe Clamps. To
attach the PCL-100, loosen
the Wing Nut, open the
hinged clamp, and slide the
PCX-100 onto the bar as
shown in Fig.a.
Latch securely Fig.b.
PCL-100 Bracket
DR-503, DR-501, and
DR-501C racks feature
PCL-100 Brackets (included
but not attached) for
mounting tom arms and
cymbal holders to the Leg
Posts. If you wish to install
them, first remove the Caps
from the Leg Posts by
inserting a coin into the slot
as shown and twisting the
Caps loose.
Place the PCL-100 Bracket
on the top of the Leg Post
and secure it by tightening
the Allen screws with the
provided Allen Wrench.
PCX-200 Pipe Clamp
The optional PCX-200 Pipe
Clamp features a swivel
bracket for added versatility. To attach the PCX-200,
loosen the Wing Nut, open
the hinged clamp, and slide
the PCX- 200 onto the bar
as shown in Fig.a. Latch
securely Fig.b.
Note
Additional brackets can be
purchased separately.
Note
The PCL-100 accepts Tom
Arms and Cymbal Holders
22.2mm (7/8") in diameter.
Note
The PCX-100 accepts Tom
Arms and Cymbal Holders
15.9 to 28.6mm (5/8" to
1-1/8") in diameter.
Note
The PCX-200 accepts Tom
Arms and Cymbal Holders
12.7 to 28.6mm (1/2" to
1-1/8") in diameter.
Page 4
Caution
Repositioning Pipe Clamps
To prevent damage to drums, cymbals, or accessories
remove them prior to repositioning the Pipe Clamps.
Adjusting Rack Bars
To prevent damage to drums, cymbals, or accessories
remove them prior to repositioning the Rack Bars.
http://www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-1501-
Loading...