P-DUKE TEN06-48S33, TEN06-48S12, TEN06-48S05, TEN06-48D12, TEN06-24S33 Datasheet

...

TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted

• PACKAGE, 1. 61 x 1.02 x 0.33 INCH

• NO EXTERNAL INPU T AND OUTPU T CAPACITOR NEEDED

• 2:1 WIDE INPUT VOLTAGE RANGE

• LOW RIPPLE & NOISE

• FIVE-SIDED SHIELD

• OVER CURRENT PROTECTION

• SHORT CIRCUIT PROTECTION

• LONG LIFE WI THOUT ELECTROLYTIC CAPACITOR

The TEN06 series offer 6 watts of output power from a 1.61 x 1.02 x 0.33 inch package without derating to 50 2:1 wide input voltage of 4.5-9, 9-18, 18-36 and 36-75VDC and features 500VAC of isolation, short-circuit protection. The safety meets to EN60950 and UL1950. All models are particularly suited to telecommunications, industrial, mobile telecom and test equipment applications.

ºC and without external input/output capacitor. The TEN06 series with

OUTPUT SPECIFICATIONS

Maximum output power 6 Watts Voltage accuracy Full load and nominal Vin ± 2%

Minimum load

Line regulation LL to HL at Full Load Load regulation 10% to 100% FL Ripple and noise 50MHz bandwidth 120mVp-p, max Maximum temperature drift Transient response recovery time 25% load step change 500uS, typ Short circuit protection Continuous, automatics recovery

Over current protection 150%, typ.

0.02% / ºC

0.2%

0.5%

INPUT SPECIFICATIONS

5V nominal input

Input voltage range

Input filter

Input surge voltage 100mS max

Remote ON/OFF See figure 1

12V nominal input 24V nominal input 48V nominal input

5V nominal input 12V nominal input 24V nominal input

48V nominal input

4.5 – 9VDC 9 – 18VDC

18 – 36VDC 36 – 75VDC

L-C filter

15VDC 36VDC 50VDC

100VDC

OUTPUT VOLTAGE ADJUSTMENT TERMINAL(Vset ) (Note1)

Model number Open -Vout shorted +Vout shorted XXS33

XXS05 XXS12 XXD12

Model number Open XXS33

XXS05 XXS12 XXD12

3.3V 5V

12V

12V

3.3V 5V

12V

12V

3.67V 6V

15V

15V

-Vout connected

with resistance (2)

3.3 to 3.67V (3-1) 5 to 6V (3-3)

12 to 15V (3-5)

12 to 15V (3-6)

2.84V

4.3V

+Vout connected

with resistance (2)

3.3 to 2.84V (3-2) 5 to 4.3V (3-4)

GENERAL SPECIFICATIONS

Efficiency See table

Isolation voltage

Isolation resistance Isolation capacitance 300 pF,max

Safety standard pending IEC60950, J60950, UL60950, EN60950

Switching frequency Full load to No load 100 to 1500 KHz Case material Metal case

Base material None

Weight 20.0g (0.71oz)

Dimension

MTBF (Note 4) 650Fit (1500000hrs, 100% Load)

Input to Output Input to Case Output to Case Input to Output Input to Case Output to Case

500 Vac

DC500V 50M ohms

1.61 x 1.02 x 0.33 Inch (41 x 25.8 x 8.5 mm)

ENVIRO NMENTAL SPECIFICATIONS

Operating temperature range (with derating) -20ºC to +70ºC Storage temperature range -40ºC to +85ºC Cooling Nature convection Thermal shock MIL-STD-810D

Vibration Shock 100G

Operating humidity range 20% to 95% RH Storage humidity range 20% to 95% RH

At no operation, 10~55~10Hz (sweep for 15min.) amplitude 1.

5mm constant (maximum 9G X, Y, Z 2hrs each)

EMC CHARACTERISTICS

Meet EN55022 classes A recommend circuit with external capacitor filter at input ( Note 5 )

EMC external circuit

Input

DC-DC

Converter

5V input 220uF/16V

12V input 220uF/25V 24V input 100uF/50V 48V input 100uF/100V

Output

(7)

Model

Number

TEN06-05S33 4.5 – 9 VDC 3.3 VDC 2.84 – 3.67 VDC TEN06-05S05 4.5 – 9 VDC 5 VDC 4.3 – 6 VDC TEN06-05S12 4.5 – 9 VDC 12 VDC 12 – 15 VDC TEN06-05D12 4.5 – 9 VDC 12 VDC 12 – 15 VDC TEN06-12S33 9 – 18 VDC 3.3 VDC 2.84 – 3.67 VDC TEN06-12S05 9 – 18 VDC 5 VDC 4.3 – 6 VDC TEN06-12S12 9 – 18 VDC 12 VDC 12 – 15 VDC TEN06-12D12 9 – 18 VDC 12 VDC 12 – 15 VDC TEN06-24S33 18 – 36 VDC 3.3 VDC 2.84 – 3.67 VDC TEN06-24S05 18 – 36 VDC 5 VDC 4.3 – 6 VDC TEN06-24S12 18 – 36 VDC 12 VDC 12 – 15 VDC TEN06-24D12 18 – 36 VDC 12 VDC 12 – 15 VDC TEN06-48S33 36 – 75 VDC 3.3 VDC 2.84 – 3.67 VDC TEN06-48S05 36 – 75 VDC 5 VDC 4.3 – 6 VDC TEN06-48S12 36 – 75 VDC 12 VDC 12 – 15 VDC TEN06-48D12 36 – 75 VDC 12 VDC 12 – 15 VDC

Input

Range

Output

Voltage

Output

Voltage Range

Note

1. The follow output voltage can be outputted by connecting this terminal to an output + or – terminal. Unless the output voltage is adjusted, this terminal should be open.

2. In addition, the voltage can be adjusted not by shorting these terminals,

but by connecting them to resistances as shown below.

3. Arithmetic expression connected resistance: R ( K )

3-1 Vo=(3.3*R+36.7)/(R+10) 3-2 Vo=(3.3*R+36.7)/(R+12.92) 3-3 Vo=2.5*[2+2.7/(R+6.8)] 3-4 Vo=2.5*[2-2.7/(R+9.5)] 3-5 Vo=2.5+9.5(R+10.9)/(R+.2) 3-6 Vo=2.5+22*(R+12.7)/(R+10)(Between two outputs)

4. Bellcore TR-NWT-000332. Case1:50% Stress, temperature at 40ºC.

(Ground fixed and controlled environment)

5. The filter capacitor recommended use “ CHEMICON “ KMF series or

equivalent impedance at 0.16 ~ 0.33 ( 100KHz 20 )

6. Maximum value at nominal input voltage and full load.

7. Typical value at nominal input voltage and full load.

8. Test by minimum Vin and constant resistor load.

EXTERNAL OU TPUT TRIMMING

Output can be externally trimmed by using the method shown below. ( ) for dual output trim

TRIM UP

5(4)

6(6)

7(7)

TRIM DOWN

100

OUTPUT POWER (%)

Derating Curve

75 50

Nature convection

AMBIENT TEMPERATURE (ºC)

30 40 50 60 70 80-20 0-10

Output

Current

1200 mA 1212 mA 1000 mA 1429 mA

500 mA 1622 mA 250 mA 1667 mA 1500 mA 604 mA 1200 mA 658 mA

500 mA 617 mA 250 mA 617 mA 1500 mA 286 mA 1200 mA 321 mA

500 mA 309 mA 250 mA 309 mA 1500 mA 143 mA

1200mA 165 mA

500 mA 155 mA 250 mA 155 mA

LL DIMENSIONS IN INCHES (mm)

Input

Current

BOTTOM

VIEW

(6)

PIN SINGLE DUAL

1 + Vi + Vi 2 Ctrl Ctrl 3 - Vi - Vi 4 NC - Vo 5 - Vo COM 6 Vset Vset 7 + Vo + Vo

Eff

(%)

70 6600 uF 74 3000 uF 78 1400 uF 76 510 uF 73 6600 uF 80 3000 uF 85 1400 uF 85 510 uF 77 6600 uF 82 3000 uF 85 1400 uF 85 510 uF 77 6600 uF 80 3000 uF 85 1400 uF 85 510 uF

Capacitor Load max

PIN CONNECTION

(8)