PDUKE PDL02-05S05, PDL02-05S09, PDL02-05S12, PDL02-05S15, PDL02-05S33 Datasheet
...
• SIP PACKAGE, 0.86 x 0.36x 0.44 INCH
• NO EXTERNAL INPUT AND OUTPUT CAPACITOR NEEDED
• 2:1 WIDE INPUT VOLTAGE RANGE
• LOW RIPPLE & NOISE
• UL94-V0 CASE POTTING MATERIALS
• INPUT TO OUTPUT ISOLATION UP TO 1KV
• CONTINUOUS SHORT CIRCUIT PROTECTION
• EXTERNAL ON/OFF CONTROL
TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted
The PDL02 series offer 2 watts of output power from a 21.8 x 9.2 x 11.1 mm package
without derating to 85
with 2:1 wide input voltage of 4.5-9, 9-18, 18-36 and 36-75VDC and features 1000VDC
of isolation, short-circuit. The safety meets to EN60950 and UL60950. All models are
particularly suited to telecommunications, industrial, mobile telecom and test
equipment applications.
ºC and without external input/output capacitor. The PDL02 series
OUTPUT SPECIFICATIONS
Output power 2 Watts max
Voltage accuracy Full load and nominal Vin ± 2%
Minimum load (Note 1)
Line regulation LL to HL at Full Load
Load regulation 25% to 100% FL
Ripple and noise 20MHz bandwidth 50mVp-p
Temperature coefficient
Transient response recovery time 25% load step change 500uS typ
Short circuit protection Continuous, automatics recovery
25% of FL
± 0.5%
± 0.75%
0.1% / ºC, max
INPUT SPECIFICATIONS
5V nominal input
Input voltage range
Input filter Capacitor type
Input surge voltage
100mS max
Reflected repple current
There is an external
capacitor at input (Note 2)
Start up time Nominal Vin and constant resistor load 1mS typ
Remote ON/OFF
Remote off input current
Application circuit
4mA current
Source
+Input
-Input
DC-DC ON
1KΩ
12V nominal input
24V nominal input
48V nominal input
5V input
12V input
24V input
48V input
5V input (100uF)
12V input (100uF)
24V input (10uF)
48V input (10uF)
DC-DC ON
DC-DC OFF
Nominal input
+Input
ctrl
4mA current
Source
-Input
Open or high impedance
Control pin applied current
3 ~ 6mA max(via 1K)
DC-DC OFF
1KΩ
4.5 – 9VDC
9 – 18VDC
18 – 36VDC
36 – 75VDC
15VDC
36VDC
50VDC
100VDC
400mAp-p max
150mAp-p max
380mAp-p max
170mAp-p max
1mA max
ctrl
GENERAL SPECIFICATIO NS
Efficiency See table
Isolation voltage 1000VDC, min
Isolation resistance
Isolation capacitance 300pF, max
Safety standard pending IEC60950, UL60950, EN60950
Switching frequency Full load to minimum load 100 to 650KHz
Case material Non-conductive black plastic
Base material None
Potting material Silicon (UL94-V0)
Dimensions
Weight 4.8g (0.17oz)
MTBF (Note 3) 5.107 x 106 hrs
0.86 X 0.36 X 0.44 Inch
(21.8 X 9.2 X 11.1 mm)
109ohms, min
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range -40ºC to +85ºC
Storage temperature range -55ºC to +105ºC
Cooling Nature convection
Thermal shock MIL-STD-810D
Vibration 10~55Hz, 2G, 30minutes along X,Y and Z
Relative humidity 5% to 95% RH
EMC CHARACTERISTICS
Meet EN55022 classes B recommend
circuit with external L-C filter at input (Note
4)
EMC external circuit
+
Input
-
DC-DC
Converter
5V input
12V input
24V input
48V input
100uF & 10uH
100uF & 10uH
10uF & 120uH
10uF & 120uH
Output
-
(6)
(7)
(
)
Input
Number
PDL02-05S33 4.5 – 9 VDC 3.3 VDC 125mA 500mA
PDL02-05S05 4.5 – 9 VDC 5 VDC 100mA 400mA
PDL02-05S09 4.5 – 9 VDC 9 VDC 55mA 222mA
PDL02-05S12 4.5 – 9 VDC 12 VDC 42mA 167mA
PDL02-05S15 4.5 – 9 VDC 15 VDC 33mA 134mA
PDL02-12S33 9 – 18 VDC 3.3 VDC 125mA 500mA
PDL02-12S05 9 – 18 VDC 5 VDC 100mA 400mA
PDL02-12S09 9 – 18 VDC 9 VDC 55mA 222mA 222mA 79 470uF
PDL02-12S12 9 – 18 VDC 12 VDC 42mA 167mA 219mA 80 170uF
PDL02-12S15 9 – 18 VDC 15 VDC 33m A 134mA 220mA 80 110uF
PDL02-24S33 18 – 36 VDC 3.3 VDC 125mA 500mA 102mA 71 2200uF
PDL02-24S05 18 – 36 VDC 5 VDC 100mA 400mA 115mA 76 1000uF
PDL02-24S19 18 – 36 VDC 9 VDC 55mA 222mA 109mA 80 470uF
PDL02-24S12 18 – 36 VDC 12 VDC 42mA 167mA 109mA 80 170uF
PDL02-24S15 18 – 36 VDC 15 VDC 33mA 134mA 108mA 81 110uF
PDL02-48S33 36 – 75 VDC 3.3 VDC 125mA 500mA 52mA 70 2200uF
PDL02-48S05 36 – 75 VDC 5 VDC 100mA 400mA 60mA 73 1000uF
PDL02-48S09 36 – 75 VDC 9 VDC 55mA 222mA 56mA 78 470uF
PDL02-48S12 36 – 75 VDC 12 VDC 42mA 167mA 55mA 79 170uF
PDL02-48S15 36 – 75 VDC 15 VDC 33mA 134mA 55mA 79 110uF
Note
1. The PDL02 series required a minimum 25% loading on the output to maintain
specified regulation. Operation under no-load condition will not damage these
devices, however they may not meet all listed specification.
2. It is no damage on the device without external input capac itor. There is smaller
reflected ripple current when put a capacitor at input. The capacitor recommended
use “CHEMICON” LXZ series or equivalent for 05 & 12Vin.
use “CHEMICON” KMF series or equivalent for 24 & 48Vin.
3. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground
fixed and controlled environment).
4. The PDL02 series cannot meet EN55022 classes A if there is no filter at input. The
filter capacitor recommended is same as note2.
5. Maximum value at nominal input voltage and full l oad.
6. Typical value at nominal input voltage and full load.
7. Test by minimum Vin and constant resistor load.
100
75
50
25
0
OUTPUT POWER (%)
PDL02-48S33
Derating Curve
Nature convection
AMBIENT TEM PERATUR E (º C )
Range
50 60 70 80 90
Output
Voltage
100 -40 -25 0 -10
Output Current Model
Min Load Full Load
0.36
(9.20)
0.44
(11.10)
0.16
4.10)±0.5
0.10(2.54)
0.13
(3.20)
Input
Current
(5)
540mA
645mA
596mA
598mA
582mA
208mA
234mA
BOTTOM VIEW
0.08
(2.01)±0.5
0.86(21.80)
Eff
Capacitor
(%)
65 2200uF
66 1000uF
71 470uF
71 170uF
73 110uF
70 2200uF
75 1000uF
FRONT VIEW
1 2 3 5 6 7 8
0.70(17.78
1. ALL DIMENSION S IN IN C H E S (mm)
Load max
.0.01
(0.32)
Rectangular pin
(0.50)
0.02
0.02
(0.50)±0.05
PDL02-48S33
Efficiency VS Input voltage
72
71
70
69
68
67
66
65
EFFICIENCY (%)
60
55
50
40
INPUT VOLTAGE (V)
50 55 60 65 70
45
75 36
PDL02-48S33
Efficiency VS Output load
72
71
70
69
68
67
66
65
EFFICIENCY (%)
60
55
50
0.1 0.2
OUTPUT LOAD (A)
PIN CONNECTION
PIN DEFINE
1 - I NPUT
2 + INPUT
3 CTRL
5 NC
6 + OUTPUT
7 - OUTPUT
8 NC
0.3 0.4 0.5
Loading...