PDUKE OPN20-05S1P5, OPN20-05S2P5, OPN20-05S2P1, OPN20-05S1P8, OPN20-03S1P5 Datasheet

...

• NON-ISOLATION REGULATED OUTPUT VOLTAGE

• REMOTE ON/OFF

• ADJUSTABLE OUTPUT VOLTAGE

• OVER CURRENT P ROTECTION

• HIGH EFFICI EN CY UP TO 91%

• FIXED SWITCHING FREQUENCY

• SMALL 2.50” X 0.55” X 0.26” PACKAGE

The OPN20 series are non-isolation DC-DC converter packaged in a single-in-line footprint (2.5 x 0.55 x 0.26 inch) giving designers a cost effective solution for conversion from 5VDC to 3.3V, 2.5V, 2.1V, 1.8V and 1.5V and from 3.3VDC to 2.5V, 2.1V, 1.8V, 1.5V. This series was designed for applications that include distributed power, workstations, computers and servers.

TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted

OUTPUT SPECIFICATIONS

Output power 20 Watts max Voltage accuracy Full load and nominal Vin ± 2.7% Minimum load Line regulation LL to HL at Full Load Load regulation 0% to 100% FL Ripple and noise 20MHz bandwidth 100mVp-p Temperature coefficient Transient

response recovery time (see fig. 1)

Output current limit (Note 1) Latching External load capacitance 10000uF Voltage adjustability (see fig.2) Remote sense (option) Suffix-S 0.25V

Power OK, (option) Power OK signal

Lower sense threshold Upper sense threshold

Io /t = 1A/10uS Nominal input Load change step

(0% to 100% or 100% to 0% of Io, max)

Peak deviation 80mV Setting time

Suffix-K Asserts “HI” when Vout is between Following thresholds

% V setpoint

± 0.5% ± 0.5%

0.02% / ºC, max

200uS

10%

–16 ~ –10 +10 ~ +16

INPUT SPECIFICATIONS

Input voltage range Maximum input current 6000mA

Remote ON/OFF

Input reflected ripple 5~20MHz, 500uH source impedance 625mArms

3.3V nominal input (Note 2) 5V nominal input

DC-DC ON DC-DC OFF

3.3V input 2.4V < Vr < 6V 5V input 3.2V < Vr < 6V

3.0 – 3.6VDC

4.5 – 5.5VDC

Open or 0V< Vr < 1V

GENERAL SPECIFICATIONS

Efficiency See table Isolation voltage None

Switching frequency 500KHz, typ Designed meet safety standard IEC60950, UL60950, EN60950

Dimensions (see fig.3) Weight 8.5g (0.3 oz)

MTBF (Note 3) 2.064 x 106 hrs

2.50 X 0.55 X 0.26 Inch (63.5 X 14.0 X 6.6 mm)

ENVIRO NMENTAL SPECIFI CATION S

Operating temperature range (see fig. 4) –40ºC ~ +85ºC Storage temperature range –55ºC ~ +105ºC Thermal shock MIL-STD-810D Over temperature protection 125ºC

EMC CHAR ACTERISTICS

Conducted emissions EN55022 Level Radiated emissions EN55022 Level Conducted immunity EN61000-4-6 Perf. Criteria2

Rise time 80% Full load and nominal Vin 8mS,typ.

(5)

(A)

(

)

(

)

(

)

Model

Number

OPN20-03S2P5 3.0 – 3.6 VDC 2.5 VDC 6000mA 5540mA 86 OPN20-03S2P1 3.0 – 3.6 VDC 2.1 VDC 6000mA 4780mA 84 OPN20-03S1P8 3.0 – 3.6 VDC 1.8 VDC 6000mA 4200mA 82 OPN20-03S1P5 3.0 – 3.6 VDC 1.5 VDC 6000mA 3590mA 80 OPN20-05S3P3 4.5 – 5.5 VDC 3.3 VDC 6000mA 4660mA 89 OPN20-05S2P5 4.5 – 5.5 VDC 2.5 VDC 6000mA 3620mA 87 OPN20-05S2P1 4.5 – 5.5 VDC 2.1 VDC 6000mA 3120mA 85 OPN20-05S1P8 4.5 – 5.5 VDC 1.8 VDC 6000mA 2700mA 84 OPN20-05S1P5 4.5 – 5.5 VDC 1.5 VDC 6000mA 2310mA 82

Note

1. The output short circuit of the start up mode will be damage these devices. The others modes is critical protection.

2. In order to meet all specification for 3.3V input module have to add external capacitor at input. The capacitor is SANYO OS-CON,SA-series,68uF/10V

3. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment)

4. Maximum value at nominal input voltage and full load of standard type.

5. Minimum value at nominal input voltage and full load

Vo(V)

OUTPUT VOLTAGE,

Fig.1

Typical Transient Response to Step Load Change from 0% to 100% of lo, max at Room Temperature and 5V I nput (Waveform Averaged to Eliminate Ripple Component. )

(5 A/div)

Time, t(100

OUTPUT CURRENT, lo(A)

s/div)

Input

Range

0.55

(14.0)

0.12 (3.0)

0.28(7.1)

0.55 (14.0)

Output

Voltage

DC-DC POWER SIP

1 5 6 11

0.10(2.54)

(-H) Model

DC-DC POWER SIP

1 5 6 11

Output

Current

2.50(63.5)

1.90(48.3)

2.50(63.5)

Input

(4)

Current

0.025(0.64) Square pin

Eff

(%)

0.26(6.6)

0.13(3.3)

0.025(0.64) Square pin

0.09(2.3)

Fig.2

(A)

ut Current Out

EXTERNAL OUTPUT TRIMMING

Output can be externally trimmed by using the method shown below.

TRIM UP

TRIM DOWN

OPN20-03S2P5 Derat ing Cur ve

100

LMF

6 5

NATURAL

CONVECTION

3 2 1

-40

COOLING

mbient T emperature

200

LMF



300

LMF

0.28(7.1)

85 0 25 40 55 60 65 70 75 80

0.10(2.54)

1.90(48.3)

1. All dimensions in Inches (mm)

2. Pin pitch tolerance 0.014(0.35)

OPN20-05S3P3 Derating Curve

NATURAL

CONVECTION

COOLING

ut Current

Out

1 0

-40 85 0 25 40 55 60 65 70 75 80

Fig.4

100

LMF

200

LMF

300

LMF

DIP PIN CONNECTI ON

1 2 3 4 + OUTPUT 5 GND

Power OK (option) or no pin9

0.12(3.0)

0.27(6.9)

Fig.3

DEFINE

+ OUTPUT + OUTPUT

Sense (option) or no pin

GND 6 + INPUT 7 + INPUT

TRIM 10

REMOTE ON-OFF 11