P-DUKE FDC05-12S15, FDC05-12S12, FDC05-12S05, FDC05-12D15, FDC05-12D12 Datasheet

OUTPUT SPEC IFICATIONS

Output power 5 Watts max
Voltage accuracy Full load and nominal Vin ± 2%
Minimum load (Note 1)

10% of FL

Line regulation LL to HL at Full Load

± 0.2%

Load regulation

10% to 100% FL Single

Dual

± 0.2%

± 1%

Cross regulation (Dual) Asymmetrical load 25% / 100% FL ± 5%
Ripple and noise 20MHz bandwidth 50mVp-p
Temperature coefficient

I0.02% / ºC, max

Transient response
recovery time

25% load step change
FL to 1/2 FL I1% error band

Single 200uS

Dual 200uS

Over load protection % of FL at nominal input 170% typ
Short circuit protection Continuous, automatics recovery

INPUT SPECIFICA TIONS

Input voltage range

FDC05

FDC05-W

12V nominal input
24V nominal input
48V nominal input
24V nominal input
48V nominal input

9 – 18VDC
18 – 36VDC
36 – 75VDC

9 – 36VDC
18 – 75VDC

Input filter Pi type
Input surge voltage

100mS max

12V input
24V input
48V input

36VDC
50VDC

100VDC

Input reflected ripple (Note 2) Nominal Vin and full load 20mAp-p
Start up time Nominal Vin and constant resistor load 600mS typ

Remote ON/OFF (Note 3)
(Positive logic)

(Negative logic)
Remote off input current

DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
Nominal Vin

Open or 3.5V < Vr < 12V

Short or 0V < Vr < 1.2V
Short or 0V < Vr < 1.2V

Open or 3.5V < Vr < 12V

2.5mA

GENERAL SPECIFICATIONS

Efficiency See table
Isolation Voltage Input to Output to Case 1600VDC, min
Isolation resistance

10

9

ohms, min

Isolation capacitance 300pF, ma

x

Switching frequency

Standard
“W” series

300KHz, typ
200KHz, typ

Approvals and standard IEC60950, UL1950, EN60950
Case material Nickel-coated coppe

r

Base material Non-conducted black plastic
Potting material Epoxy (UL94-V0)

Dimensions

2.00 X 1.00 X 0.40 Inch
(50.8 X 25.4 X 10.2 mm)

Weight 27g (0.95oz)
MTBF (Note 4) 3.145 x 106 hrs

ENVIRONMENTAL SPECIFICATIONS

Operating temperature range
(Reference derating curve)

Standard
M1 (Note 5)
M2 (W series)

-25ºC ~ +85ºC (with derating)

-40ºC ~ +85ºC (non-derating)

-40ºC ~ +85ºC (with derating)

Maximum case temperature +100ºC
Storage temperature range -55ºC ~ +105ºC

Thermal impedance (Note 6)

Nature convection
Nature convection with heat-sink

12ºC

/

watt

10ºC

/

watt

Thermal shock MIL-STD-810D
Vibration 10~55Hz, 2G, 30minutes along X,Y and Z
Relative humidity 5% to 95% RH

EMC CHARACTER IS TI CS

Conducted emissions EN55022 Level A
Radiated emissions EN55022 Level A
ESD EN61000-4-2 Perf. Criteria

2

Radiated immunity EN61000-4-3 Perf. Criteria

2

Fast transient EN61000-4-4 Perf. Criteria

2

Surge EN61000-4-5 Perf. Criteria

2

Conducted immunity EN61000-4-6 Perf. Criteria

2

The FDC05 and FDC05-W series offer 5 watts of output power from a 2 x 1 x 0.4 inch
package without derating to 71ºC ambient temperature. FDC05 series have 2:1 wide input
voltage of 9-18, 18-36 and 36-75VDC. FDC05-W series have 4:1 ultra wide input voltage of
9-36 and 18-75VDC. The FDC05 and FDC05-W features 1600VDC of isolation, short-circuit
protection, as well as six sided shielding. The safety approve with EN60950 and UL1950. All
models are particularly suited to telecommunications, industrial, mobile telecom and test
equipment applications. According the extended operation temperature range, there are
“M1” and “M2” version for special application.

TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherw ise noted

UL E193009
TUV R3-50007936
CB JPTUV-003641
CE MARK

• 5 WATTS OUTPUT POWER

• 2:1 AND 4:1 WIDE INPUT VOLTA GE RANGE

• INTERNATIONAL SAFETY STANDARD APPROVAL

• SIX-SIDED CONTINUOUS SHIELD

• HIGH EFFICIENCY UP TO 83%

• STANDARD 2” X 1” X 0.4” PACKAGE

• FIXED SWITCHING FREQUENCY

Model

Number

Input

Range

Output

Voltage

Output

Current

Input

Current

(7)

Eff

(8)

(%)

Capacitor

Load max

(9)

FDC05-12S33 9 – 18 VDC 3.3 VDC 1000mA

387mA

75 3700uF

FDC05-12S05 9 – 18 VDC 5 VDC 1000mA

556mA

79 1700uF
FDC05-12S12 9 – 18 VDC 12 VDC 470mA 610mA 81 290uF
FDC05-12S15 9 – 18 VDC 15 VDC 400mA 658mA 80 188uF
FDC05-12D05 9 – 18 VDC ± 5 VDC ± 500mA 595mA 74 ± 850uF
FDC05-12D12 9 – 18 VDC ± 12 VDC ± 230mA 597mA 81 ± 140uF
FDC05-12D15 9 – 18 VDC ± 15 VDC ± 190mA 609mA 82 ± 47uF

FDC05-24S33 (W) 18 – 36 (9 – 36) VDC 3.3 VDC 1000mA 199 (196mA) 73 (74) 3700uF
FDC05-24S05 (W) 18 – 36 (9 – 36) VDC 5 VDC 1000mA 282 (274mA) 78 (80) 1700uF
FDC05-24S12 (W) 18 – 36 (9 – 36) VDC 12 VDC 470mA 305 (301mA) 81 (82) 290uF

FDC05-24S15 (W) 18 – 36 (9 – 36) VDC 15 VDC 400mA 325 (325mA) 81 (81) 188uF
FDC05-24D05 (W) 18 – 36 (9 – 36) VDC ± 5 VDC ± 500mA 289 (289mA) 76 (76) ± 850uF
FDC05-24D12 (W) 18 – 36 (9 – 36) VDC ± 12 VDC ± 230mA 295 (295mA) 82 (82) ± 140uF
FDC05-24D15 (W) 18 – 36 (9 – 36) VDC ± 15 VDC ± 190mA 308 (301mA) 81 (83) ± 47uF
FDC05-48S33 (W) 36 – 75 (18 – 75) VDC 3.3 VDC 1000mA 100 (100m A ) 73 (73) 3700uF
FDC05-48S05 (W) 36 – 75 (18 – 75) VDC 5 VDC 1000mA 145 (149mA) 76 (74) 1700uF
FDC05-48S12 (W) 36 – 75 (18 – 75) VDC 12 VDC 470mA 151 (151mA) 82 (82) 290uF
FDC05-48S15 (W) 36 – 75 (18 – 75) VDC 15 VDC 400mA 160 (163mA) 82 (81) 188uF
FDC05-48D05 (W) 36 – 75 (18 – 75) VDC ± 5 VDC ± 500mA 149 (149mA) 74 (74) ± 850uF
FDC05-48D12 (W) 36 – 75 (18 – 75) VDC ± 12 VDC ± 230mA 149 (149mA) 81 (81) ± 140uF
FDC05-48D15 (W) 36 – 75 (18 – 75) VDC ± 15 VDC ± 190mA 154 (154mA) 81 (81) ± 47uF

PIN CONNECTION

PIN

SINGLE

DUAL OUTPUT

1 + INPUT + INPUT
2 - INPUT - INPUT
3 + OUTPUT + OUTPUT
4 NO PIN

COMMON
5 - OUTPUT - OUTPUT
6 CTRL (Option) CTRL (Option)

1. All dimensions in Inches (mm)

2. Pin Pitch tolerance I0.014(0.35)

2.00(50.8)

0.40
(10.2)

0.40
(10.2)

0.50
(12.7)

1.00(25.4)

0.10(2.5)

0.20(5.1)

0.80(20.3) 0.60(15.2)

0.22(5.6)

0.40
(10.2)

DIA. 0.04(1. 0)

1 2

34 5

6

Bottom

V

iew

Note

1. The FDC05 (W) series required a minimum 10% loading on the output to maintain specified
regulation. Operation under no-load condition will not damage these devices, however they may not
meet all listed specification

2. Simulated source impedance of 12uH. 12uH inductor on series with + Vin.

3. The ON/OFF control is option function. There are positive logic and negative logic. The pin voltage is
referenced to negative input
To order positive logic ON-OFF control add the suffix-P (Ex: FDC05-24S05-P)
To order negative logic ON-OFF control add the suffix-N (Ex: FDC05-24S05-N)

4. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC.

(Ground fixed and controlled environment)

5. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than
standard and M2 version.

6. Heat sink is optional and P/N: 7G-0020A.

7. Maximum value at nominal input voltage and full load of standard type.

8. Typical value at nominal input voltage and full load.

9. Test by minimum Vin and constant resistor load.

0.4 0.6 0.8 1.00.05 0.2

45

65

OUTPUT LOAD (A

)

EFFICIENCY (%)

FDC05-48S05
Efficiency VS Output load

82
81
80
79
78
77
76
75
70

50 60 70 80 90

100 -40 -25 0 -10

25

50

75

100

0

AMBIENT T EMPERATURE (ºC )

OUTPUT POWER (% )

FDC05-48S05 Derating Curve

Nature convection

50 60 70 80 90

100-40 -25 0-10

25

50

75

100

0

AMBIENT TEMPERATUR E (ºC)

OUTPUT POWER (%)

FDC05-48S05-M1 Derating Curve

Nature convection

50 60 70 80 90

100 -40 -25 0 -10

25

50

75

100

0

A

MBIENT TEMPERATURE (ºC)

OUTPUT POWER

(%)

FDC05-48S05 Derating Curve
Wi

t

h HEAT-SINK (N

ote5)

Nature convection