P-DUKE DU1P0-05S12, DU1P0-05S05, DU1P0-05D15, DU1P0-05D12, DU1P0-05D05 Datasheet

...

• 1 WATT UNREGULATED OUTPUT POWER

• SINGLE-IN-LINE PACKAGE (SIP)

• HIGH EFFICIENCY FOR LOW POWER APPLICATION

• UL 94-V0 NON-CONDUCTED C ASE

• INTERNAL INPUT & O UTP U T FILTER

• INPUT / OUTPUT ISOLATION UP TO 3KVDC

The DU1P0 series are the standard building blocks for on-board distributed power systems. They are ideally suited to providing single and dual supplies on primarily digital boards with added benefit of galvanic isolation to reduce switching noise. All of the rated power may be drawn from a single pin provided the total load does not exceed 1 watt.

TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted

OUTPUT SPECIFICATIONS

Output power Voltage accuracy Full load and nominal Vin ± 5% Minimum load (Note 1) 10% of FL Line regulation LL to HL at Full Load 1.3% / 1% of Vin

Load regulation 20% to 100% FL Ripple and noise 20MHz bandwidth 100mVp-p

T e mperature coefficient Short circuit protection Short term

5V output others

1 Watt max

± 10%

± 8%

I0.1% / ºC, max

INPUT SPECIFICATIONS

Input voltage range

Input filter Capacitor

5V nominal input 12V nominal input 15V nominal input 24V nominal input

4.5 – 5.5VDC

10.8 – 13.2VDC

13.5 – 16.5VDC

21.6 – 26.4VDC

GENERAL SPECIFICATIONS

Efficiency See table Isolation voltage Input to Output Isolation resistance

Isolation capacitance 30pF , ma Switching frequency 60KHz, min Design meet safety standard UL1950, EN60950 Case material Non-conductive black plastic Base material None Potting material Epoxy (UL94-V0)

Dimensions Weight 2.0g (0.071oz)

MTBF (Note 2) 1.471 x 107 hrs

Standard 1000VDC, min Suffix-N 3000VDC, min

0.77 X 0.24 X 0.40 Inch (19.6 X 6.0 X 10.2 mm)

ohms, min

ENVIRONMENTAL SPECIFICATIONS

Operating temperature range -25ºC ~ +85ºC (with derating) Storage temperature range -55ºC ~ +105ºC Thermal shock MIL-STD-810D Vibration 10~55Hz, 2G, 30minutes along X,Y and Z Relative humidity 5% to 95% RH

(4)

(

)

Model

Number

DU1P0-05S05 4.5 – 5.5 VDC 5 VDC 200mA DU1P0-05S12 4.5 – 5.5 VDC 12 VDC 83mA DU1P0-05S15 4.5 – 5.5 VDC 15 VDC 67mA DU1P0-05D05 4.5 – 5.5 VDC ± 5 VDC ± 100mA DU1P0-05D12 4.5 – 5.5 VDC ± 12 VDC ± 42mA DU1P0-05D15 4.5 – 5.5 VDC ± 15 VDC ± 33mA DU1P0-12S05 10. 8 – 13.2 VDC 5 VDC 200mA DU1P0-12S12 10.8 – 13.2 VDC 12 VDC 83mA 111mA 79 6.2uF DU1P0-12S15 10. 8 – 13.2 VDC 15 VDC 67mA 112mA 79 6.2uF DU1P0-12D05 10.8 – 13.2 VDC ± 5 VDC ± 100mA 119mA 74 3.0uF DU1P0-12D12 10.8 – 13.2 VDC ± 12 VDC ± 42mA 111mA 80 3.0uF DU1P0-12D15 10.8 – 13.2 VDC ± 15 VDC ± 33mA 109mA 80 3.0uF DU1P0-15S05 13.5 – 16.5 VDC 5 VDC 200mA 97mA 73 6.2uF DU1P0-15S12 13.5 – 16.5 VDC 12 VDC 83mA 89mA 79 6.2uF DU1P0-15S15 13.5 – 16.5 VDC 15 VDC 67mA 89mA 79 6.2uF DU1P0-15D05 13.5 – 16.5 VDC ± 5 VDC ± 100mA 95mA 74 3.0uF DU1P0-15D12 13.5 – 16.5 VDC ± 12 VDC ± 42mA 88mA 80 3.0uF DU1P0-15D15 13.5 – 16.5 VDC ± 15 VDC ± 33mA 87mA 80 3.0uF DU1P0-24S05 21.6 – 26.4 VDC 5 VDC 200mA 62mA 71 6.2uF DU1P0-24S12 21.6 – 26.4 VDC 12 VDC 83mA 58mA 76 6.2uF DU1P0-24S15 21.6 – 26.4 VDC 15 VDC 67mA 57mA 78 6.2uF DU1P0-24D05 21.6 – 26.4 VDC ± 5 VDC ± 100mA 61mA 72 3.0uF DU1P0-24D12 21.6 – 26.4 VDC ± 12 VDC ± 42mA 57mA 78 3.0uF DU1P0-24D15 21.6 – 26.4 VDC ± 15 VDC ± 33mA 55mA 79 3.0uF

Input

Range

Output

Voltage

Note

1. The DU1P0 series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification

2. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment).

3. Maximum value at nominal input voltage and full load of standard type.

4. Typical value at nominal input voltage and full load.

5. Test by minimum Vin and constant resistor load.

Output

Current

0.016(0.4

0.14

3.6

0.085(2.16

0.24(6.1

Input

298mA 269mA 272mA 295mA 273mA 268mA 121mA

0.77(19.6)

(3)

Current

FRONT VIEW

0.20(5.08)

BOTTOM VIEW

1 2 4 5 6 7

Eff

(%)

71 6.2uF 78 6.2uF 78 6.2uF 72 3.0uF 78 3.0uF 78 3.0uF 73 6.2uF

0.10(2.54)

Capacitor

Load max

0.40(10.2)

0.01x 0.02 ( 0.25 x 0.5) Rectangular Pin

0.053(1.35

(5)

DU1P0-24S05 Derating Curve

100

75 50 25

OUTPUT POWER (%)

Nature convection

50 60 70 80 90

AMBIENT TE M P E RATURE (ºC)

STANDARD

PIN SINGLE DUAL

1 + INPUT + INPUT 2 - INP U T - INPUT 4 - OUT PUT 5 NC COMMON

100 -40 -25 0 -10

6 + OUTPUT + OUTPUT

1. All dimensions in Inches (mm)

2. Pin pitch tolerance I0.014(0.35)

PIN SINGLE DUAL

1 + INPUT + INPUT 2 - INP U T - INPUT

-OUTPUT 5 - OUT PUT - OUTPUT 6 NC COMMON 7 + OUTPUT + OUTPUT

“N” Models