PDR Mounts upm100L User Manual
Mounts by
A division of David Engineering & Mfg. Inc.
Model
UPM100L /UPM100XL LOCKING PROJECTOR MOUNT
Thank you for purchasing the PDR Projector mount with the Security locking features.
To ensure the correct usage, please read and follow the instructions
All PDR mounts and adapters carry a lifetime warranty against defects in material and workmanship. We are not liable for
improper installation that results in damage to mounts, adapters or presentation equipment.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight of both the projector
and the mount.
Fully tighten all of the mounting screws as specified in the instructions.
=Complete security features (anti-theft)
=Simple to adjust, no tools required
=Security lock included
=To be used with any standard 1 ½” NPT pipe
=14 deg Pitch + 30 deg Yaw adjustments
=360° rotation
=
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the mount from the wall/ceiling later, you will find the screw holes and anchor bolts for the
mounting unit left on the wall.
Adjustable 1 ½” NPT Telescoping Pipe
Special techniques are necessary for installation of the projector display mount.
Features
& Ceiling mount (Sold separately)
=Quick projector removal with exclusive
“Slide bay locking system”
manual thoroughly. Please store the instructions in a safe place
for future reference.
Pitch and Yaw adjustments
Rotate 360 deg
Ceiling Mounting Flange And
Telescoping Pipe
Sold Separately
Security Lock
1
INSTALLATION LOCATION
The ceiling where the mount is to be installed must be capable of long-term support of
the total load of the projector and mount. Measures should be taken to ensure sufficient
strength to withstand the force of earthquakes, vibrations and other external forces.
Note:
Incorrect installation can cause the projector mount to fall and cause injury.
Total load of the mount (Projector + Mount)
Maximum weight - 80 Lbs ( 36Kg.)
INSTALLATION ON A WOODEN WALL
Always install so that the load is supported by a wood stud. If
Do not install on decorative posts or plaster board.
NOTE: PDR offers an FCP (false ceiling panel) kit as a separate option.
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
water is possible. These can result in fire or electric shock.
Do not install close to an air conditioner intake or outlet. Do
oily smoke or tobacco smoke. Fire could result.
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation..
The internal temperature could elevate and possibly result in fire.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the projector mount
falling.
Do not install where there is direct sunlight or other strong
.
WARNING
the strength of the wood studs is not sufficient, add reinforcement.
Always confirm the center of the stud is used for the installation.
CAUTION
not install in locations where there are excessive amounts of dust,
light. Strong light could result in eye fatigue during usage.
Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the projector
mount falls.
Do not alter any of the parts. Do not use broken parts. This
C a u t i o n : I n s t a l l a t i o n o f u n i t i s t o b e c a r r i e d o u t b y q u a l i f i e d t e c h n i c i a n s o n l y. I n s t a l l i n a n a p p r o p r i a t e
l o c a t i o n b y c h e c k i n g t h e w a l l s t r u c t u r e a n d d u r a b i l i t y f o r s a f e t y a n d a c c i d e n t p r e v e n t i o n .
WARNING
could result with injury due to the projector mount falling. .
REV 081408
2
Loading...