PDR Mounts pdm110f User Manual

Mounts by

A division of David Engineering & Mfg. Inc.

M odel

PDM 110/120F PANEL DISPLAY MOUNT

Thank you for purchasing the PDR panel display wall mount.
To ensure the correct usage, please read and follow the instructions

All PDR mounts and adapters carry a limited lifetime warranty from ship date against defects in material and workmanship.
Check the PDR website for details @ www.PDRmounts.com. We are not liable for improper installation that results in damage
to mounts, adapters or presentation equipment.

To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight of both the panel
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.

manual thoroughly. Please store the instructions in a safe place

Special techniques are necessary for installation of the panel display mount.

Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and
airflow.

for future reference.

Parts Configuration Chart Features

A

B

C

See model #

D

5/16" Flat washers…4 pcs

E

5/16" x 2 1/2” Lag bolts …4 pcs

F

See Model

Display bracket .... 2 pcs

Model # 110 = 20” Model # 120 = 14”

Wall mount bracket…1 pc

Model # 110 = 32” Model # 120 = 24”

Locking bar... 1 pc

K

L

6mm x 40 mm Phillip screws...4 pcs

M

5 mm x 40 mm Phillip screws...4 pcs

Low profile 1 5/8”
16" or 24" stud mounting points ( MODEL #110 )
Easy installation
Flat or 5 deg tilt (no tools required)
Lateral movement from center for better viewing position

Mounting points for panel display models

Fig 1

Panel Display mounting slots

Top

5 mm x 16 mm Phillip screws…4 pcs

G

6 mm x 16 mm Phillip screws…4 pcs

H

8 mm x 16 mm Phillip screws...4 pcs

I

8 mm x 40 mm Phillip screws...4 pcs

O

Bottom

4 mm x 16 mm Phillip screws...4 pcs

P

4mm steel flat washer...4 pcs

Square multi-mount washers...4 pcs

J

Use with #110

Use with #120

Plastic spacer 3/4 x 1”...4 pcs

1

INSTALLATION LOCATION

WARNING

The wall where the wall mount is to
the panel display and wall mount. Measures should al
withstand the force of earthquakes, vi

Note: Incorrect installation can cause the p

be installed must be capable of long-term support of the total load of

bration and other external forces.

anel display to fall and cause injury.

Total load of the panel (p

MAXIMUM WEIGHT - 200 lbs. (92 Kg.)

INSTALLATION ON A WOODEN WALL

Always install so that the load is supported by a wood stud. If
Do not install on decorative posts or plaster board.

the strength of the wood studs is not sufficient, add reinforcement.

Always confirm the center of the stud is used for the installation.

CAUTION

Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any

water is possible. These can result in fire or electric shock.

Do not install close to an air conditioner intake or outlet. Do
oily smoke or tobacco smoke. Fire could result. .
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation..
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.

Install only on a vertical surface. Avoid
elevate and possibly result in fire. Injury or damage could also result from falling. .
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
falling. .

Do not install where there is direct sunlight or other strong

.

sloped surfaces. Also, do not install facing upward. The internal temperature could

so be taken to ensure sufficient strength to

anel display + wall mount)

.

not install in locations where there are excessive amounts of dust,

light. Strong light could result in eye fatigue during usage.

WARNING

Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the pan
display falls.
Do not alter any of the parts. Do not use broken parts. This

Make sure that both hooks from each pivot bracket engage with the wall bracket. Failure to do so could cause the panel display
to fall.

Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.

could result with injury due to the panel display falling.

C a u t i o n : I n s t a l l a t i o n o f u n i t i s t o b e c a r r i e d o u t b y q u a l i f i e d t e c h n i c i a n s o n l y. I n s t a l l i n a n a p p r o p r i a t e
l o c a t i o n b y c h e c k i n g t h e w a l l s t r u c t u r e a n d d u r a b i l i t y f o r s a f e t y a n d a c c i d e n t p r e v e n t i o n .

Rev 032107

2

el