PDR Mounts awm250 User Manual

Mounts by

A division of David Engineering & Mfg. Inc.

Model

AWM250 ARTICULATING WALL MOUNT INSTRUCTIONS

Thank you for purchasing the PDR mount.
To ensure the correct usage, please read and follow the instructions

All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable
for improper installation that results in damage to mounts, adapters or presentation equipment.
To register visit our web site @ www.pdrmounts.com

Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a
airflow.

Special techniques are necessary for installation of the panel display mount.

manual thoroughly. Please store the instructions in a safe place

for future reference.

nd

he

To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.

Features

Features:

RSimple to adjust
R250 lb load rating ( 50” to 71” TV max recommended ) adapter may be required for large displays
RRugged heavy gauge metal construction
RTension adjustment on all joints “ANTI-CREEP TENSION ADJUSTMENT”
RTough powder-coated “Matte Black” finish
RExtends 25.1” from wall and closes to 4.7”
RPivots left or right tilts up 5 deg, down 15deg
RCable management included
RLimited lifetime manufacturer warranty on defects in material or workmanship
RMade in the USA

Fig 1

of both the panel

1

INSTALLATION LOCATION

WARNING

The wall where the wall mount is to
the panel display and wall mount. Measures should al
withstand the force of earthquakes,

Note: Incorrect installation can cause the

be installed must be capable of long-term support of the total load of

vibration and other external forces.

panel display to fall and cause injury.

Total load ( panel display + mount )

MAXIMUM WEIGHT - 250 Lbs. ( 113 Kg.)

INSTALLATION ON A WOODEN WALL

Always install so that the load is supported by a wood stud. If
Do not install on decorative posts or plaster board.

the strength of the wood studs is not sufficient, add reinforcement.

Always confirm the center of the stud is used for the installation.

CAUTION

Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any

water is possible. These can result in fire or electric shock.

Do not install close to an air conditioner intake or outlet. Do
oily smoke or tobacco smoke. Fire could result.
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation..
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.

Install only on a vertical surface. Avoid
elevate and possibly result in fire. Injury or damage could also result from falling.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
falling.

Do not install where there is direct sunlight or other strong

.

sloped surfaces. Also, do not install facing upward. The internal temperature could

so be taken to ensure sufficient strength to

not install in locations where there are excessive amounts of dust,

light. Strong light could result in eye fatigue during usage.

C a u ti o n : I n s t a ll a t io n of u ni t i s t o b e c ar r ie d o ut b y q u a l i fi e d t e c h n i ci a n s o n ly. I n s t a ll i n a n a p p ro p ri a t e
l o c at i o n b y c h e ck i ng t h e w a l l st r u ct u r e a n d d ur a b il i t y f o r s a f e t y a n d a c c i d en t pr e v en t i on .

Rev 050608

WARNING

Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the pan
display falls.
Do not alter any of the parts. Do not use broken parts. This
Make sure that both hooks from each pivot bracket engage with the wall bracket . Failure to do so could cause the panel
display to fall.
Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.

could result with injury due to the panel display falling.

2

el

DRAWING SPECIFICATIONS

25.10 FULLY EXTENDED

15°

24.61

32.00”

29.5 max”

1.75 min”

25.50”

5°

4.68”

13.76”

.32 DIA TYP

3