PCT 9030 UNI-SEAL, 9030 US Instructions Manual
Compression Tool
for TRS Series 6/59 and DRS Series 7/11 Connectors
To Compress RG6 and RG59 Connectors
1. Press cable and insert fully into connector. Open tool handle. (Fig. 1)
2. Tilt connector so that center conductor fits into hole in
compression tip. (Fig. 2) Once connector is seated on
compression tip, press down on top of spring loaded fingers with
cable causing fingers to separate. Pass cable through both sets
of fingers, so that fingers are fully closed around cable.
9030 UNI-SEAL
COMPRESSION TOOL
Instructions
4. Slowly close tool until stops touch at end of handles. (Fig. 5)
Once cycle is completed, open tool. (Fig. 1)
With tool open, position compressed connector between
fingers and end of compression tip. (Fig. 6) Lift cable up to
remove compressed connector from tool. Take care not to
bend the center conductor during the removal process. Check
center conductor for any distortion prior to use. If you have a
problem removing cable, you may use the manual finger
release on the bottom of the tool. (Fig. 6)
3. Slowly close tool (Fig. 3) making sure that connector seats
inside counter-bored surface on finger face (Fig. 4). Check to
make sure fingers are closed around connector before continuing.
WARNING: This tool should not be used on live electrical circuits. It is not protected against electrical shock. Always use
OSHA/ANSI or other industry approved eye protection when using tools. This tool is not to be used for purposes
other than intended.
ALWAYS WEAR SAFETY GLASSES!
© 2009-2014 PCT International, Inc. All rights reserved. www.pctinternational.com
Corporate Headquarters: 2260 W Broadway Rd | Mesa, Arizona 85202-1898 | USA | Tel +1.480.813.0925 | Fax +1.480.545.1080 | info@pctintl.com
To Compress RG7 and RG11 Connectors
1. Follow the same procedures shown above, with the exception
of compression finger location. To compress the connector,
use the RG7/11 finger location. (Fig. 7)
Reminder: Position compressed connector between fingers
and end of tip before removing connector from the tool
Manual_CompTool9030_20140512a
Specifications subject to change without notice.
CABLE TYPE
Series 59
60% thru Quad
Series 6
60% thru Quad
Series 6
Plenum
Series 7
60% thru Quad
Series 11
60% thru Quad
CONNECTOR
PART NUMBER
PCT-TRS-59/59L
PCT-TRS-6/6L
PCT-TRS-6P
PCT-DRS-7
PCT-DRS-11/11L
Series QR320 PCT-DRS-320QR
RECOMMENDED TOOLS
PCT-TRS-CT
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
PCT-TRS-CT
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
PCT-TRS-CT
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
PCT-TRS-CT-AS
PCT-RH-CT-AS
9030 US
Tool Maintenance
A “3-In-1” oil should be applied at regular intervals to all
exposed pins, pivot points, and moving parts.
Warranty
Warranty is limited to the repair or replacement of any
product which proves to be defective in material or
manufacture under normal use and service.
© 2009-2014 PCT International, Inc. All rights reserved. www.pctinternational.com
Corporate Headquarters: 2260 W Broadway Rd | Mesa, Arizona 85202-1898 | USA | Tel +1.480.813.0925 | Fax +1.480.545.1080 | info@pctintl.com
Manual_CompTool9030_20140512a
Specifications subject to change without notice.
Loading...