pcl DTA-2198 Owner's Manual
Front panel the TV set
VIDEO L-AUDIO-R
R/LAudio
Video
Power Indicator
TV/DVD MENU V- V+ P- P+
Power Switch
Play/pause the DVD
The DVD Player
Signal Receiver
TV/DVD Switching
Rear panel of the TV set
Digital audio coaxial output terminal
DVD EXT
COAXIAL
TV EXT
DVD SCART Terminal
TV SCART Terminal
Menu
Stop the DVD
Open/close the DVD
Channel Position up/down
Volume up/ down
COAXIAL
Swap function enables quick swap to the last watched program.
Auto scan function enables automatic successive scanning of all the programs in
memory with (each channel will last about 2 seconds)."OFF" skip status
Program swap and auto scan functions
Program swap
SWAP
1 Suppose the channel number
you used just now is 8 and the
channel number you are using
is 18 (as shown in the figure).
2 If you want to return to the
last watched program channel
8, you can simply press the
SWAP button.
3 If you want to return to
channel 18, press the button
again. Through this function,
you can easily change
between the channel you are
using and the channel you
used last time.
18
AUTO
I
8
AUTO
I
18
AUTO
I
SCAN
Auto program scan
1 Press the SCAN button to
scan through all the memorized
TV channels. The scan will
pause for about 2 seconds on
each channel.
2 If you want to stop the function
during auto scanning, simply
press the SCAN button again.
3
AUTO
I
SCAN
1
AUTO
I
SCAN
1
AUTO
I
SCAN
2
AUTO
I
SCAN
P
V
Semi-automatic search
TUNE
P+
MENU
V+
Semi-automatic search
1 Press the P+/- buttons or
PROGRAM NUMBER 0-9
buttons to choose desired
channels I.E. channel 1
2 Press the TUNE button, the
TUNE menu shown on the right
display on the screen.
3 buttons to
Press the P+/-
select " SEARCH".
1
AUTO
I
TUNE
COLOUR AUTO
BAND VHFL
SKIP OFF
PROGRAM 0
SEARCH
FINE TUNE
AUTO SEARCH
4 Press the V-/+ buttons to
start searching.
The V- down button is used for
lower side program search.
The V+ up button is used for
higher side program search.
Repeat this step, till find the
desired channel.
6
SEARCH
152.25MHz
To turn off the on-screen menu
EXIT
In general, after you press the MENU button, the menu
display (PICTURE, TIME
, FUNCTION, TUNE, EXCHANGE,
ETC.) will automatically disappear within 15 seconds. If you
want to eliminate these contents immediately, please press
the EXIT button.
item
P
V
P
V
Program skip
Program skip
Channels can be set so that they are skipped during
program selection.
P+
MENU
V+
1 Press the P+/- buttons or
PROGRAM NUMBER 0-9
button to choose desired
1
AUTO
I
channels I.E. channel 1
2 Press the TUNE button , the
TUNE
TUNE menu shown on the right
display on the screen.
3 buttons to
Press the P+/-
select "SKIP".
TUNE
COLOUR AUTO
BAND VHFL
SKIP OFF
PROGRAM 0
SEARCH
FINE TUNE
AUTO SEARCH
4 Press the V-/+ buttons to
P+
MENU
V+
turn the SKIP function "ON".
5 Press the TUNE button to close
the menu. When you use the P /
buttons to select channel, this
TUNE
COLOUR AUTO
BAND VHFL
SKIP ON
PROGRAM 0
SEARCH
FINE TUNE
+-
AUTO SEARCH
channel will be skipped. However,
you can still use the PROGRAM
NUMBER buttons to select the
skipped channel numbers.
If you want to recover the skipped channel
1 Use the PROGRAM NUMBER buttons to select the channel
number to be recovered.
2 Repeat those steps just now.
3 Press the V-/+ buttons to turn the SKIP function "OFF".
P
V
P
V
Black Stretch Automatically increases the contrast range
Noise Reduce Picture Noise & Grain Reduction Circuit. (Use only on poor reception)
Black stretch and noise reduce
PICTURE
P+
MENU
V+
How to select BLACK STRETCH
1 Press the button, the
PICTURE
right display on the screen.
2 buttons to
Press the P+/-
PICTURE
menu shown on the
PICTURE
CONTRAST 48
BRIGHTNESS 32
COLOUR 48
SHARPNESS 40
*HUE 60
BLACK STRETCH OFF
select "BLACK STRETCH".
PICTURE
CONTRAST 48
3 Press the V-/+ buttons to
turn the BLACK STRETCH
function "ON" or "OFF".
How to select NOISE REDUCE
BRIGHTNESS 32
COLOUR 48
SHARPNESS 40
*HUE 60
BLACK STRETCH ON
FUNCTION
P+
MENU
V+
1 Press the FUNCTION button,
the menu shown on
FUNCTION
the right display on the screen.
2 buttons to
Press the P+/-
select "NOISE REDUCE".
FUNCTION
BACKGROUND ON
NOISE REDUCE ON
FADE ON
CHILD LOCK OFF
AVL ON
CALENDAR
FUNCTION
BACKGROUND ON
NOISE REDUCE OFF
3 Press the V-/+ buttons to
turn the NOISE REDUCE
function "ON" or "OFF".
FADE ON
CHILD LOCK OFF
AVL ON
CALENDAR
Loading...