PCE Instruments PCE-WM1-ICA, PCE-WM1 Users guide

PCE Americas Inc.

Manual
Moisture Meter
PCE-WM 1

711 Commerce Way
Suite 8
Jupiter
FL-33458
USA
From outside US: +1
Tel: [phone]
Fax: [phone]
[email protected]

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: [phone]

Fax: [phone]

[email protected]

1. APPLICATION

Thermo-Hygrometer PCE-WM 1 is an electronic microprocessor based device for
measuring relative air humidity (%RH), temperature (°C), absolute humidity (g/m3) and dew
point temperature (°C). It is equipped with TP-1 Electrode which enables the user to obtain
temperature readings for various surfaces (e.g. steel constructions). Absolute humidity and
dew point temperature are calculated by the microprocessor, which performs linearization
and mathematical computations.
The device is widely used in industry and laboratories, it is extremely user friendly. It is
supplied together with other standard equipment in a shock proof case.

2. TECHNICAL DATA

RELATIVE HUMIDITY (%RH)

Range 10 % - 95 %
Sensor type EE HC 200 (Austria)
Response time T90 15 s
Accuracy ±2 % (± 3 %)

TEMPERATURE (°C)

Range - 20°C - 80°C
Sensor type EE KF 6645 (Austria)
Response time T90 15 s
Accuracy ± 0.5°C
Resolution 0.1 °C

SURFACE TEMPERATURE (°C)

Range - 20°C - 80°C
Sensor type EE KF 6645 (Austria)
Response time T90 240 s
Accuracy ± 0.5°C
Resolution 0.1 °C
Electrode fastening magnetic grip

ABSOLUTE HUMIDITY (g/m3)

Absolute humidity is calculated by the microprocessor using formulas commonly known in
thermodynamics.

DEW POINT TEMPERATURE (°C)

Dew point temperature is determined by the microprocessor using a two dimensional

(humidity and temperature) table.
REMAINING TECHNICAL DATA
Display LCD 31/2 digits

Nonlinearity correction yes
Power 9V, battery 6F22
Auto power off yes, after 4 min.
Size
instrument 165*80*33 mm

case 270*180*55 mm

2

3. PREPARING THE INSTRUMENT FOR MEASUREMENTS

Before starting the measurement connect the probe to the instrument.

4. MEASUREMENTS

The instrument is turned on by pressing the ON/OFF button once. The results of
measurements of air temperature, relative humidity, dew point temperature and absolute
humidity are instantaneous after switching the knob to (respectively): TEMP.[°C], RH [%],
DEW POINT [°C], HUMIDITY [g/m3].

Surface temperature measurement should be conducted with the TP-1 electrode
connected to the mini-jack socket located in the lower part of the probe. Set the knob to
TEMP. [°C].

5. OUT OF RANGE INDICATION

The instrument indicates the results that are out of range in the following way:
1_ _.1 - upper temp. range exceeded (t>79.5°C),

-1_ _.1 - lower temp. range exceeded (t<-19.5°C),
1_ _.2 - upper RH range exceeded (RH%>99.9%),

-1_ _.2 - lower RH range exceeded (RH%<10%),
1_ _.3 - upper dew point temp. range exceeded
(tdp>79.5°C),

-1_ _.3 - lower dew point temp. range exceeded
(t

<-19.5°C).

dp

6. REPLACING THE BATTERY

The instrument is powered by one 9V battery type 6F22. The battery should be replaced
when the “LO BAT” sign is displayed on the LCD. To replace the battery remove the cap,
unscrew the screw holding the two halves of the case together and carefully separate them.

7. EXPLOITATION REMARKS

7.1 Do not allow the cold humidity sensor to come in contact with warm and humid air. This

causes condensation and totally falsifies the results. Condensation does not damage the

sensors nor does it change its characteristic.

7.2 Humidity sensor is not resistant to acetone or other chemical solvents.

7.3 If the sensors become dusted wash it gently with alcohol and let to dry. Mechanical

cleaning is not allowed as it may case scratches.

8. HUMIDITY STANDARDS

Periodical verification of the Ther mo-Hygrometer PCE-WM 1 operation can be done with
appropriate saturated salts solutions or humidity generators. Checking can be done by the
manufacturer or other specialized company. It is recommended to calibrate the instrument
every 12 months.

9. GUARANTEE AND SERVICE
PCE.Group warrants the Thermo-Hygrometer PCE-WM 1 to be free from malfunction and
defects in both materials and workmanship for one year (12 months) from the date of
purchase.

3

If the Thermo-Hygrometer PCE-WM 1 does not function properly during the warranty
period due to defects in either, materials or workmanship, our company will, at its option,
either repair or replace the instrument without charge, subject to the conditions and
limitations stated herein. Such repair service will include any necessary adjustments and
replacement part.

Limitations

This warranty does not cover damage that may occur if you use excess force (in variance
with instructions of this users manual) to hammer the device into the wood.

This warranty becomes null and void if you fail to pack your PCE-WM1 in a manner
consistent with the original product packaging and damage occurs during product shipment.

This warranty does not cover: circumstance beyond our company’s control; service
required as the result of unauthorized modifications or service; misuse, abuse; failure to
follow our company operating or maintenance instructions.

Repair or replacement without charge is our company’s only obligation under this
warranty. Our company will not be responsible for any special, consequential or incidental
damages resulting from the purchase, use, or improper functioning of this equipment
regardless of the cause. Such damages for which our company’s will not be responsible
include, but are not limited to, loss of revenue or profit, downtime costs, loss of use of the
equipment, cost of any substitute equipment, facilities of services, or claims of your
customers for such damages.

4