PCE Instruments PCE-TT 3 User Manual

PCE-TT 3 Digital Multimeter
User Manual
français, italiano, español, português, nederlands,
türk, polski, русский, 中文) can be downloaded here:
www.pce-instruments.com
Last change: 9 August 2017
v1.0
English
© PCE Instruments
Contents
1 Safety notes ....................................................................................... 1
2 Specifications .................................................................................... 2
3 Operation ........................................................................................... 3
3.1 Function wheel ........................................................................................................................3
3.2 Mode button ............................................................................................................................3
3.3 Range button ...........................................................................................................................3
3.4 Hold button ..............................................................................................................................3
3.5 Voltage measurement .............................................................................................................3
3.6 Resistance measurement .......................................................................................................3
3.7 Diode test ................................................................................................................................3
3.8 Continuity test..........................................................................................................................4
3.9 Current measurement .............................................................................................................4
3.10 Non-contact voltage test .........................................................................................................4
4 Warranty ............................................................................................ 5
5 Disposal ................................ ............................................................. 5
© PCE Instruments
1 Safety notes
Please read this manual carefully and completely before you use the device for the first time. The device may only be used by qualified personnel and repaired by PCE Instruments personnel. Damage or injuries caused by non-observance of the manual are excluded from our liability and not covered by our warranty.
The device must only be used as described in this instruction manual. If used
otherwise, this can cause dangerous situations for the user and damage to the meter.
The instrument may only be used if the environmental conditions (temperature,
relative humidity, …) are within the ranges stated in the technical specifications. Do
not expose the device to extreme temperatures, direct sunlight, extreme humidity or moisture.
Do not expose the device to shocks or strong vibrations.  The case should only be opened by qualified PCE Instruments personnel.  Never use the instrument when your hands are wet.  You must not make any technical changes to the device.  The appliance should only be cleaned with a damp cloth. Use only pH-neutral
cleaner, no abrasives or solvents.
The device must only be used with accessories from PCE Instruments or equivalent.  Before each use, inspect the case for visible damage. If any damage is visible, do not
use the device.
Do not use the instrument in explosive atmospheres.  The measurement range as stated in the specifications must not be exceeded under
any circumstances.
Never touch live parts during the measurement. There is danger to life due to electric
shock.
Do not touch the non-insulated parts of the measuring tips as this can cause electric
shock.
Before each measurement, make sure that the proper measurement range is selected
and that the test leads are connected correctly.
Resistance and diode tests must only be carried out on voltage-free parts and
conductors.
Non-observance of the safety notes can cause damage to the device and injuries to
the user. We do not assume liability for printing errors or any other mistakes in this manual. We expressly point to our general guarantee terms which can be found in our general terms of
business. If you have any questions please contact PCE Instruments. The contact details can be found at
the end of this manual.
© PCE Instruments
1
2 Specifications
Parameter
Measuring range
Resolution
Accuracy
DC voltage
200.0 mV
0.1 mV
±(0.08 % + 2 digits)
2.000 V
1 mV
±(1.0 % + 2 digits)
20.00 V
10 mV
200.0 V
100 mV
600 V
1 V
±(1.2 % + 2 digits)
AC voltage
200.0 mV
0.1 mV
±(1.2 % + 35 digits)
2.000 V
1 mV
±(1.2 % + 8 digits)
20.00 V
10 mV
200.0 V
100 mV
600 V
1 V
±(1.5 % + 8 digits)
Resistance
200.0 Ω
0.1 Ω
±(1.0 % + 2 digits)
2.000 KΩ
1 Ω
±(1.5 % + 2 digits)
20.00 KΩ
10 Ω
200.0 KΩ
100 Ω
2.000 MΩ
1 KΩ
±(2.5 % + 3 digits)
20.00 MΩ
10 KΩ
±(3.5 % + 5 digits)
DC current
20.00 mA
0.01 mA
±(1.5 % + 5 digits)
200.0 mA
0.1 mA
AC current (50-400 Hz)
20.00 mA
0.01 mA
±(2.0 % + 5 digits)
200.0 mA
0.1 mA
Parameter
Input limit
mA DC, mA ACV DC
200 mA DC/AC V AC
600 V DC/AC
Resistance, continuity test, diode test
250 V DC/AC
Diode test
0.9 mA / 1.5 V
Continuity test
< 150 Ω / < 0.5 mA
Overload
"OL" indication on display
Sampling rate
2 / sec.
Input resistance
10 MΩ VDC / VAC
Display
LCD with 2,000 digits
Operating temperature
5 ° C ... 40 ° C (41 ° F ... 104 ° F)
Storage temperature
- 20 ° C ... 60 ° C (- 4 ° F ... 140 ° F)
Operating humidity
<31 ° C to 80% RH; 31 <40 ° C to 50% RH
Storage humidity
<80% RH
Measurement category
CAT III 600 V
Battery
2 x 1.5 V AAA
Automatic shutdown
After about 15 minutes
Dimensions / Weight
220 x 40 x 33 mm / 215g
© PCE Instruments
2
3 Operation
3.1 Function wheel
Use the function wheel to select the desired measuring function. You have 5 different settings:
1. Off
2. Voltage measurement (“V”)
3. Resistance measurement, diode test, continuity test (“Ω“)
4. Current measurement (“mA”)
5. Non-contact voltage measurement (“NCV”)
3.2 Mode button
With the mode button, you can switch between different measuring modes within the selected measuring function. For example, you can switch between AC and DC measurement or between resistance measurement, diode test and continuity test.
3.3 Range button
Use the range button to change the measuring range and accuracy of the selected function. Keep in mind that the measuring range might be exceeded when changing switching to a smaller measuring range. In this case, the display shows an overload indication. Switch to a higher measuring range or to the auto measuring mode by pressing and holding the range button for 2 seconds. If the overload indication does not disappear the parameter to be measured is too high and cannot be measured with the multimeter. This might cause damage to the device.
3.4 Hold button
By pressing the hold button, you can freeze the current reading on the display. The display shows a hold indication. To unfreeze the reading, press the hold, range or mode button or use the function wheel.
3.5 Voltage measurement
To use the voltage measurement function, connect the test lead to the device. Next, turn the tip of the device clockwise until the measuring tip comes out. Select the voltage measurement function by using the function wheel. Use the mode button to select AC or DC measurement. Now you can perform a voltage measurement.
3.6 Resistance measurement
To use the resistance measurement function, connect the test lead to the device. Next, turn the tip of the device clockwise until the measuring tip comes out. Select the resistance measurement function by using the function wheel. Now you can perform a resistance measurement.
3.7 Diode test
In order to use the diode test function, follow the steps in chapter 3.6 and press the mode button to switch to the diode test function. Now you can check diodes.
© PCE Instruments
3
3.8 Continuity test
In order to use the diode test function, follow the steps in chapter 3.6 and press the mode button twice to switch to the continuity test function. If the resistance is lower than 150 Ω the device gives out an acoustic signal.
3.9 Current measurement
To use the current measurement function, connect the test lead to the device. Next, turn the tip of the device clockwise until the measuring tip comes out. Select the current measurement function by using the function wheel. Use the mode button to select AC or DC measurement. Now you can perform a current measurement.
3.10 Non-contact voltage test
The non-contact voltage test function can only be used on AC voltages. Use the function wheel to select the non-contact voltage test. Now you can hold the tip of the device against the wire to be tested. If the wire is live the red LED at the tip of the device will light up. The non-contact voltage test can be performed at a distance of 3-4 cm.
© PCE Instruments
4
4 Warranty
You can read our warranty terms in our General Business Terms which you can find here:
https://www.pce-instruments.com/english/terms.
5 Disposal
For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament applies. Due to the contained pollutants, batteries must not be disposed of as household waste. They must be given to collection points designed for that purpose.
In order to comply with the EU directive 2012/19/EU we take our devices back. We either re-use them or give them to a recycling company which disposes of the devices in line with law.
For countries outside the EU, batteries and devices should be disposed of in accordance with your local waste regulations.
If you have any questions, please contact PCE Instruments.
© PCE Instruments
5
PCE Instruments contact information
Germany France Spain
PCE Deutschland GmbH PCE Instruments France EURL PCE Ibérica S.L. Im Langel 4 23, rue de Strasbourg Calle Mayor, 53 D-59872 Meschede 67250 SOULTZ-SOUS-FORETS 02500 Tobarra (Albacete) Deutschland France España Tel.: +49 (0) 2903 976 99 0 Téléphone: +33 (0) 972 3537 17 Tel. : +34 967 543 548 Fax: +49 (0) 2903 976 99 29 Numéro de fax: +33 (0) 972 3537 18 Fax: +34 967 543 542 info@pce-instruments.com info@pce-france.fr info@pce-iberica.es www.pce-instruments.com/deutsch www.pce-instruments.com/french www.pce-instruments.com/espanol
United States of America United Kingdom Italy
PCE Americas Inc. PCE Instruments UK Ltd PCE Italia s.r.l. 711 Commerce Way suite 8 Units 12/13 Southpoint Business Park Via Pesciatina 878 / B-Interno 6 Jupiter / Palm Beach Ensign Way, Southampton 55010 LOC. GRAGNANO 33458 FL Hampshire CAPANNORI (LUCCA) USA United Kingdom, SO31 4RF Italia Tel: +1 (561) 320-9162 Tel: +44 (0) 2380 98703 0 Telefono: +39 0583 975 114 Fax: +1 (561) 320-9176 Fax: +44 (0) 2380 98703 9 Fax: +39 0583 974 824 info@pce-americas.com info@industrial-needs.com info@pce-italia.it www.pce-instruments.com/us www.pce-instruments.com/english www.pce-instruments.com/italiano
The Netherlands Chile Hong Kong
PCE Brookhuis B.V. PCE Instruments Chile S.A. PCE Instruments HK Ltd. Institutenweg 15 RUT: 76.154.057-2 Unit J, 21/F., COS Centre 7521 PH Enschede Santos Dumont 738, local 4 56 Tsun Yip Street Nederland Comuna de Recoleta, Santiago, Chile Kwun Tong Telefoon: +31 (0) 900 1200 003 Tel. : +56 2 24053238 Kowloon, Hong Kong Fax: +31 53 430 36 46 Fax: +56 2 2873 3777 Tel: +852-301-84912 info@pcebenelux.nl info@pce-instruments.cl jyi@pce-instruments.com www.pce-instruments.com/dutch www.pce-instruments.com/chile www.pce-instruments.cn
China
PCE (Beijing) Technology Co.,Ltd PCE Teknik Cihazları Ltd.Şti. 1519 Room, 4 Building Halkalı Merkez Mah. Men Tou Gou Xin Cheng, Pehlivan Sok. No.6/C Men Tou Gou District 34303 Küçükçekmece - İstanbul 102300 Beijing Türkiye China Tel: 0212 471 11 47 Tel: +86 (10) 8893 9660 Faks: 0212 705 53 93 info@pce-instruments.cn info@pce-cihazlari.com.tr www.pce-instruments.cn www.pce-instruments.com/turkish
Turkey
© PCE Instruments
6
Loading...