Page 1
PIPE INSPECTION
CAMERA
Please read the manual carefully before operating the system.
Please charge the battery before using.
MANUAL
Page 2
2
Catalog
CATALOG ................................................................................... 2
SAFETY AND NOTICE .................................................................. 3
1. PARTS LIST ............................................................................. 5
1.1 ACCESSORIES .......................................................................................................... 5
1.2 CONTROLLER ...................................................................................................... 7
2. QUICK START GUIDE .............................................................. 8
2.1 GET ACCESSORIES AND CHARGE THE BATTERY ................................................................. 8
2.2 CONNECTION .......................................................................................................... 8
2.3 ASSEMBLE SKID ..................................................................................................... 10
2.4 STARTING UP ........................................................................................................ 11
3. MENU .................................................................................. 12
3.1 VIDEO SETTINGS ..................................................................................................... 13
3.2 SYSTEM SETTINGS ................................................................................................ 14
4.KEYBOARD ............................................................................ 18
Page 3
3
Safety and Notice
To Avoid electrical shock put the item indoor when Charging
Warning
Use only input 110~240V AC output DC 13.5V, 5000mA charger.
This machine can only use the original charger and lithium battery, reminding
the charging time is 5 hours. Please charge the battery before use!
Warning
Please check the appearance and functionality of the goods upon receipt. In the event of damaged
or missing goods, please forward images to us within 3 working days, as we will otherwise be
unable to rectify.
1Please check the appearance and functionality of the goods upon receipt. In the event of damaged
or missing goods, please forward images to us within 3 working days, as we will otherwise be unab
le to rectify.
2The camera system operating temperature is between -10ºC ~ 50ºC (14ºF ~ 122ºF).
3The warranty becomes void if any physical damage is present by user or force majeure factors or
if the system is disassembled or connect non-factory parts by the user
4Do not disconnect the SD card while recording or playing as this may damage the system and/or
the SD card
5Remember to always back up the data on your SD card
6Before initial use of a memory card, it is recommended to use the inspection system to format the
card first.
Page 4
4
7Remember to slide the write-protect tab to the unlock position. Otherwise, all data on the memory
card is protected and the card cannot be edited or formatted.
8Use only the original accessories to avoid possible risks to health and property, and thus meet all
related legal regulations.
9Keep controller dry.
10Do not drop, knock, or shake the inspection system. Inappropriate behavior when using the
camera system may damage the internal electronic circuit board or deform the lens shape.
Page 5
5
1. Parts list
1.1 Accessories
Item
Image
Description
Optional
Controller
⚫ Size: 401 * 240 * 86.5mm
⚫ Display: 10.1 inch HD LCD,
⚫ Pixel 1280 * 800
⚫ Storage medium: 64G SD card (max 256G)
⚫ Battery: Li-ion- Battery 6000MAH 12V
⚫ Running Time: ＞4hours
√
Cable wheel
⚫ Size: 875 * 978 * 460mm
⚫ Cable length: 60m,
⚫ Cable diameter: Ø10.3mm,
⚫ 9 cores, Shielded coaxial cable
⚫ Cable wheel material: stainless steel and
aluminum alloy
⚫ Counter accuracy: 0.1M
⚫ Counter deviation:±1％
⚫ Waterproof keyboard
⚫ Size: 301 * 116 * 12mm
√
Camera Head &
Skids
⚫ Size: Ø60*144mm
⚫ Camera light: 4PCS highlight LEDS
⚫ Pixels: 1920*1080
⚫ Viewing angle: 105°
⚫ Skid Size: Ø80MM
⚫ Skid Size: Ø170~300MM
√
Camera
⚫ Size: Ø50*118mm
⚫ Pixels: 1920*1080
⚫ Viewing angle: 105°
⚫ Camera light: 6PCS highlight LEDS
⚫ SKID:Φ110mm、Φ150mm、Φ210mm
√
Transmitter
⚫ Size: φ32*70MM
⚫ Emission frequency: 512Hz
⚫ Effective distance: 4.5M
√
Spring
⚫ Size: φ33*218mm
⚫ Weight: 0.41KG
√
Connect line
⚫ Size: ø5.3* 1000mm
√
Page 6
6
Test line
⚫ Size: ø5.3-7* 1500mm
⚫ SF12-7 Waterproof self-locking joint
√
Microphone
⚫ Frequency Response: 20-20KHz
⚫ sensitivity: 116dB
⚫ Line Length: 1.2m
√
Charger
⚫ input: AC100-240V〜50 / 60Hz
⚫ output: DC 13.5V / 5A
⚫ Output plug specification: 5521
⚫ Weight: 0.30KG
√
SD card and
card reader
⚫ 64G SD card & card reader
√
Tool Bag
⚫ Size: 400*280*210MM
√
Screw Driver
⚫ 2.5mm
√
Waterproof
Ring
√
Manual
√
Pipe Receiver
⚫ Frequency 512hz
⚫ Signal: Analog
⚫ Distance: 4.5-5m
Universal Skid
⚫ Universal skid
⚫ Skid Size: Ø170~300MM
Page 7
7
1.2 Controller
1
Visor
14
Zero count
2
Display
15
M/ft switch
3
Infrared receiving
16
Far focus
4
Record
17
Light brightness up
5
Photo/OK/ Photo folder
18
Near focus
6
Left/ Rewind/ Mute
19
Light brightness down
7
Down/ZOOM-
20
Tilt-up
8
Right/ Fast forward/ volume+
21
Pan-right
9
Return / video input switch
22
Tilt-down
10
UP/ZOOM+
23
Pan-left
11
Video directory
24
Speed range light
Page 8
8
12
Menu/ Video input switch
25
Automatic rotation/ Reset
13
ON/OFF
26
Motor speed / Count mode switch
2. Quick Start Guide
2.1 Get accessories and charge the Battery
1. Connect the adapter to
a power supply.
2. Connect the plug to the port
of the Control terminal.
3. The indicator will change from
red to green when finished
charging.
2.2 Connection
1. Take out the control terminal
and insert it into the coil
2. Tighten the screws
3. Open the sunshade
4. Connect one end of connect
line.
5. Connect the other end of the
connect line.
6. Connect keyboard.
Page 9
9
7. Put cable into the clamp.
8. Rotate copper nut and
tighten the black screw.
9. Loose the break.
10. Install camera, spring and
transmitter.
11. Locking casters.
12. Installation is completed.
WARNING:
Check the waterproof ring between all connections.
Page 10
10
Be careful:Do not turn the camera rotating part by hand to avoid damaging the motor.
Be careful: Pan tilt camera can’t be used in severe blockage and sludge pipeline, otherwise the
camera may be damaged. After use, please clean the sediment on the camera with water in time to
avoid jamming.
2.3 Assemble skid
1. Install 80mm skids
1. Remove the camera.
2. Install the skid and lock the
screws.
3. Install to the coil spring
connector.
Page 11
11
2.Install universal skid
1. Remove the camera.
2. Loose the ring in the middle
of skid, put into camera and
tighten three screws to fix.
3. Tighten the camera and coil
connector
2.4 Starting up
1. Insert SD card or card
reader & SD card
2. Plug in microphone.
3. Staring up
Long press power button
for 3 seconds to turn on.
4. Record video
Press button to record,
press again to stop recording.
5. Take photo & playback
Press button to take
photo.
Long press button to playback.
6. Audio and text record
Support to record audio by
microphone and input text by
keyboard when recording video
7. Meter counter
Press button to reset the
counter.
8. Zoom in and out
Press
9. Adjust volume
Page 12
12
counter. Press button to
switch meter/ feet.
button to zoom in and zoom out
image when recording.(max 8
levels)
When play video or photo, also
use these two buttons to
choose video or photo.
Press button to
adjust volume when recording
or play video.
10. Adjust lights of camera
Press button on
control handle to adjust lights.
11. Adjust pan tilt
Adjust the joystick on control
handle to control pan and tilt
12. Adjust manual focus
Press button on
control handle to adjust focus
of camera. (Only for 50mm
manual focus camera)
13. Play video
Press and buttons
to play video.
14. Delete video
Press and buttons
to delete video.
15. CVBS Video output
Long press menu button
for 3 seconds switch to connect
other RCA jack screen.
operate in same way back to
close video output
When play back video, press button to pause the video, and press buttons to fast
forward and backward the video.
Warning: Do not use "USB STICK" and "SD card" at the same time. Pay attention to the direction of
the SD card. Do not insert or remove the U disk or SD card during the photo/video process.
3. Menu
Press to enter menu. Press choose the items. Press enter
submenu. Press enter upper submenu until to homepage.
Play Video
Play Photo
Page 13
13
Video settings
System settings
3.1 Video settings
1.Set the length of time to record video
⚫ 5 minute
⚫ 15 minute
⚫ 30 minute
2.Audio record
⚫ ON
⚫ OFF
3.CVBS output
⚫ NTSC
⚫ PAL
Page 14
14
4.Mic volume
⚫ First press the OK key, press the left and right keys to adjust the volume
5.Time watermark
⚫ ON
⚫ OFF
3.2 System settings
1. Image
⚫ Brightness
⚫ Contrast
⚫ Chroma
⚫ Reset
Page 15
15
2. Volume
⚫ Press the left and right keys to adjust the volume
3. Language
4. Time
Date and time
Press the up and down keys to set the date and time, and press the left and right keys to select the
time and date
5. Restore default
⚫ No: Cancel
Page 16
16
⚫ Yes: Confirm
6. Format
⚫ No: Cancel
⚫ Yes: Format SD card(Note: please back up the data in the SD card before operation)
7. Firmware update
⚫ No: Don’t upgrade system
⚫ Yes: Start to upgrade
8.View software version
⚫ View software version, date
Page 17
17
Page 18
18
4.Keyboard
1. The font and character size have been set and cannot be changed.
2. The basic operation of characters is to automatically push back, covering the input characters
on the image.
3. The cursor flashing indicates the current position of the character to be input on the screen. The
cursor position can be controlled by the direction key on the keyboard. The cursor will move
from left to right, from top to bottom and back. After typing a character, the cursor flashes
quickly at the position of the next character, and then disappears. Press F6 to switch between
cursor flashing and cursor clearing.
4. Video character overlay input uses a standard American keyboard. The alphabetic characters in
the QWERTY area and the numeric characters of the keypad can be directly input to the
screen. Normally, lowercase letters are entered. When you press and hold the shift key or press
caps lock, you can enter uppercase letters. When exiting uppercase input, press caps lock
again. Use the backspace key to move the characters on the screen, which will quickly replace
the characters to the left of the cursor with blank characters, and the cursor will move to the left.
The delete key on the keyboard does not give any function. Press enter to move the cursor to
the start of the next line.
F6
The switch cursor flashes
F9
Clear screen
↑↓←→
Move cursor position
CTRL+1~8
Quick jump page
5. The video text superimposing unit displays it in the current screen page. The text written to
these pages will be saved in the local nonvolatile memory until it is overwritten. To move
between screen pages, use the page up and page down keys. To quickly jump to page 1 ~ 8,
press Ctrl + X (x stands for 1 ~ 8). Supports up to 64 page editing. To clear the screen page of
the text, press F9.
Loading...