PCE Instruments PCE-MTS500-DFG N 5K-KIT, PCE-MTS500, PCE-MTS500-DFG N 5K FD 300 KIT, PCE-MTS500-FD 300 KIT Users guide

PCE Americas Inc.
711 Commerce Way
Suite 8
Jupiter
FL-33458
USA
From outside US: +1
Tel: [phone]
Fax: [phone]
[e-mail]

www.pce-instruments.com/english

www.pce-instruments.com

Test Stand for Force Gauge

PCE-MTS500

INSTRUCTION MANUAL

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: [phone]

Fax: [phone]

[e-mail]

CONTENTS

1.Function 1

2.Structure 1

3.Installation 2

4.Specification 2

5.Attention 3

6.Operation

7.Maintenance 3

8.Packing

List 3

3

1.Function

3&(076 Electric Vertical Test Stand, applied in tension and compression test, is assembled with

2N-5kN) Series Force Gauge. The stand adopts double-column construction

(
with good stability, wide application range and easy operation. Furthermore, it has advantages
of non-polar speed adjustment, manual or automatic operation, suitable for fields of rubber & plastic
products, textile, construction, complex material, wire & cables, auto accessories, engine
and scientific research, etc.
Note: When installing different force gauge, it should equip different backboard.

2.Structure

Small Backboard

Tighten Screw of

Up Slide Carriage

Up Limit Ring

Column

Up Slide Carriage

Up Limit Screw

Force Gauge Backboard

Down Slide Carriage

Down Limit Ring

Speed Knob

Power Lamp

Power Switch

Shift Button
of Manual and
Automatic Mode

POWER

OFF ON

SPEED CONTROL

HIGH

LOW

AUTO

MANUAL

410mm

Limit Switch

Lower Limit Screw

1040mm

Up Button

UP

STOP

DOWN

Stop Button

Power Socket

Down Button

260mm

1

3.Installation of Force Gauge

M3 Screw

Force Gauge

Joint Bearing

M6 Haxangular Nut

Force Gauge

P

icture 1 Installation of

(Sensor Inside) Force Gauge

1

. When installing (Sensor Inside) Force Gauge, take out 4 pieces of M3 screws from toolbox,

Picture 2 Installa
Force Gauge

Outside Backboard

tion of

Picture 3 Instal

Force Gauge(1kN-5kN)

Sensor

lation of

and through 4 deep hole of Small Backboard, tighten them into 4 installing hole on force
gauge(Picture 1);

2. When installing Force Gauge, take off 4 pieces of M6 hexangular screws of back cover, and
backboard. also take off Small Backboard on test stand;through 4 hole of Force Gauge
backboard, tighten 4 pieces of M6 screws into insalling hole of Force Gauge by nut
(Picture 2);

3. When installing (1kN-5kN) Force Gauge, it should equip the SJ-021 Outside Backboard.
Loosen the 4 pieces of M6 hexangular screws, take off the SKN Backboard, fix the SJ-021
Backboard on the position of Force Gauge Backboard by the 4 screws;Take one of the joint
axletree from sensor toolbox, and tighten the sensor through hole of
backboard as showing in picture(Picture 3).

4. Specification

Capacity
Measuring Stroke
Measuring Speed
Maximum Gap
Work Voltage
Rate Current
Fuse of Main Circuit
Fuse of Controlling Circuit
Working Temperature
Store & Delivery Temperature
Relative Humidity

2

5.Attention

A. Please do not take Up or Lower Limit Screw at any time to prevent screw mandrel from getting

out or damaging to other accessories.

B. When needing to move UP Slide Carriage for appropriate space, please pay attention:

1. Loosen the tighten screw at two side of Up Slide Carriage, during which it should support the

slide carriage by hands to avoid dropping down.

2. The Up Slide Carriage will not upper than the top of column, and lower than Up Limit Screw.

C. Operation

Examine Before Operation

A. Check Tighten Screw of Up Slide Carriage to be locked firmly;
B. Turn on the power switch, then the power lamp will be light.
C. Examine the stand whether there is abnormal sound when moving without load.

Manual Test

Choose the Manual mode by pressing Shift Button of Manual and Automatic Mode;Press Up
or Down button all along, the test stand will work; Loosen the button, the test stand will stop
work and finish test.

Automatic Test

Choose the Automatic mode by pressing Shift Button of Manual and Automatic Mode;Press
Up or Down button once, the test stand will work; Press Stop button, the test stand will stop
and finish test.

7.Maintenance

A. Please keep the environment clean and prevent liquid and metal scraps from entering

the engine box, otherwise electric shock may happen and driving components may be

damaged.
B. Please keep the column and lower slide carriage hole clean.
C. Add some lubricant to screw mandrel and gear after period of time.
D. Please pull out power connector, and make the stand away from dust and moisture if it is

not used.

8.Packing List

Number

1

2

3

4

5

6

Parts Name

3&(076 Main Body

M10 Inner Hexagon Spanner

110/220V Power Wire

Manual

Qualification Certificate

Quantity

1

1

1

1

1

1

3