The FLIR ONE™ allows you to see the world in a whole new
way, with a unique blend of thermal and visible imaging.
This user guide pr ovides brief information on how to use the
FLIR ONE. Additional information is available directly from
the FLIR ONE app in the Settings menu.
PCE Americas Inc.
711 Commerce Way
Suite 8
Jupiter
FL-33458
USA
From outside US: +1
Tel: (561) 320-9162
Fax: (561) 320-9176
info@pce-americas.com
Plug the Micro USB end of the
power cable into the FLIR ONE
and plug the other end into a
USB power source.
The power/status indicator will blink while the device is
charging. The FLIR ONE requires 2-4 hours for a full charge,
depending on the power source. When the device is fully charged,
the Power/Status indicator will be on continuously.
Note: The iPhone will not charge when
the FLIR ONE is charging. Also, it is not
possible to use the iPhone cable to charge
the FLIR ONE.
TM
Charging the FLIR ONE™. /
User Manual. / 3
App Store
USER MANUAL
TM
ASSEMBLE THE FLIR ONE™
Snap the included slim case on
the iPhone, and then slide the
iPhone into the FLIR ONE.
The round opening in the slim case will align with the protrusion
on the FLIR ONE and help it stay attached to the iPhone.
When snapping the slim case onto the iPhone, it is recommended
to snap the volume button side first, to avoid damaging the iPhone.
The latest version of the FLIR ONE app is available on the
Apple App Store. If the FLIR ONE is turned off, the app will
tell you to attach your FLIR ONE camera and open the shutter.
The iPhone iOS version must be 7.1.1 or higher.
When it is in the up position, the device is turned off. When it
is in the middle position, it is turned on. When it is pulled down
to the bottom position, the device does an automatic tuning
operation, which is described below. When it is released it will
go back to the middle position.
SLEEP MODE
Your FLIR ONE will go into
‘Sleep Mode’ automatically.
To conserve the battery when the FLIR ONE APP is not the
focus, your FLIR ONE will automatically go into ‘Sleep Mode’.
To wake your FLIR ONE, momentarily close the MODE SWITCH
and return it to the open position.
FLIR ONE uses two camera apertures and an exclusive image
blending process to ensure you always know what you’re looking at. Position the camera at least an arms length or more
from your subject for optimal photos.
OPTIMIZED
+1 METER
TM
Mode Switch. /
User Manual. / 6
USER MANUAL
TM
TUNING THE FLIR ONE™
Periodically it may be necessary
to perform a Tuning operation
on the FLIR ONE.
This causes the device to do a self-calibration and allows
the thermal imager to present an optimized image and a
more accurate temperature calculation (see Spot Meter for
additional information).
which makes use of the visible camera in the FLIR ONE to
maximize detail and image sharpness. This feature requires
some amount of visible light, so in dark environments turn on
the light to enhance the image detail. This feature makes use
of the light that is built into the iPhone.
TM
Contr ol Panel. /
®
) is a patented technology
User Manual. / 10
USER MANUAL
TM
SETTINGS MENU
Configure additional features on
the FLIR ONE™.
EMISSIVITY
When the Spot Meter is enabled, the temperature displayed
is affected by many factors, including a property of the target
material known as emissivity. This property is a relative rating
of how well a material emits or radiates thermal energy.
Some materials are more emissive than others; reflective
materials like metals tend to be poor emitters. For most
materials, the default “matte” setting is a fair approximation.
SAVE GPS LOCATION
If a GPS signal is available, the location will be added to captured images. This makes it possible to see images on a map.
SAVE TO CAMERA ROLL
Turn this on to save a copy of your images and videos in the
iPhone photo gallery. Images will always be stored in the FLIR
ONE camera regardless of this setting. Items already captured
will not be copied.
TEMPERATURE UNIT
Use this setting to change the temperature unit of measure
between the Fahrenheit and Celsius scale.
Much more information about
the FLIR ONE™ is described in
the Help & Support feature within
the FLIR ONE app.
TROUBLESHOOTING
FLIR ONE not detected...
If the FLIR ONE™ app is not able to detect the FLIR ONE camera,
make sure the iPhone is properly attached to the FLIR ONE
and fully engaged. Make sure the FLIR ONE is turned on with
the mode switch in the middle position. When the FLIR ONE is
turned on, the red Power/Status indicator on the back should
be on. Make sure the FLIR ONE is adequately charged up (when
the device is plugged into a power source, the charge indicator
on the bottom of the device near the micro USB connection
will stay lit continuously if the device is fully charged).
The temperature indicated by the FLIR ONE is always a
calculated estimate and never exact. The indicated temperature is
affected by many factors, especially the emissivity of the object
being observed and the distance to the object. The temperature
may be influenced by the time of day, by weather conditions,
or by other hot or cold objects in the vicinity that may be
reflecting off the intended object.
TM
Help & Support. /
User Manual. / 12
USER MANUAL
TM
LEGAL
FCC INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
IC STATEMENT
This Class B digital apparatus complies with Canadian ICES-
003. Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
VCCI
TM
Legal. /
User Manual. / 13
USER MANUAL
TM
PRODUCT & SAFETY
BATTERY & CHARGER INFORMATION
This device has an internal, non-removable, rechargeable
battery. Do not attempt to remove the battery from the device
as you may damage the device. The battery can be charged and
discharged hundreds of times, but it will eventually wear out.
Use and standby times are estimates only. Actual times are
affected by, for example, device settings, features being used,
battery condition, and temperature.
If the battery has not been used for a long time, to begin
charging, you may need to connect the charger, then disconnect and reconnect it.
If the battery is completely discharged, it may take several
minutes before the charging indicator is displayed.
When your charger is not in use, unplug it from the electrical plug and the device. Do not leave a fully charged battery
connected to a charger, as overcharging may shorten the battery’s lifetime. If left unused, a fully charged battery will lose
its charge over time.
Always keep the battery between 15°C and 25°C (59°F
and 77°F). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not
work temporarily.
Do not dispose of batteries in a fire as they may explode. Dispose
of batteries according to local regulations. Recycle when possible.
Do not dispose as household waste.
Use the charger for its intended purpose only. Improper use
or use of unapproved chargers may present a risk of fire,
explosion, or other hazard, and may invalidate any approval
or warranty. If you believe the charger is damaged, take it to a
service center for inspection before continuing to use it. Never
use a damaged charger. Only use the charger indoors.
Handle your device, charger and accessories with care.
The following suggestions help you protect your warranty coverage.
• Keep the device dry. Precipitation, humidity, and all types
of liquids or moisture can contain minerals that corrode
electronic circuits. If your device gets wet, allow the
device to dry.
• Do not use or store the device in dusty or dirty areas.
Moving parts and electronic components can be damaged.
• Do not store the device in cold temperatures. When the
device warms to its normal temperature, moisture can
form inside the device and damage electronic circuits.
• Do not attempt to open the device.
• Unauthorized modifications may damage the device and
violate regulations governing radio devices.
• Do not drop, knock, or shake the device. Rough handling
can break internal circuit boards and mechanics.
• Use a soft, clean, dry cloth to clean the surface of
the device.
R E C Y C L E
Always return your used electronic products, batteries, and
packaging materials to dedicated collection points. This way
you help prevent uncontrolled waste disposal and promote the
recycling of materials.
The c ro ssed-out whe eled-bin symbo l on yo ur product,
battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators mus
be taken to separate collection at the end of their working
life. This requirement applies in the E uropean Union. Do not
dispose of these products as unsorted municipal waste.