The C2 Camera displays live color video to a LCD screen from an imaging
sensor and lighting source connected to a exible cable. It can be used to
look into conned or concealed areas.
The C2 Camera and its intellectual properties are covered under United
States Patent No. 6,491,408.
Safety Information
Every person using the C2 Camera, should read this operator’s manual
carefully before using it. Failure to understand and follow the contents of this manual
may result in electrical shock, re and/or severe personal injury.
Safety Instructions and UV Light Warnings
1. Do not look directly into the ultra-violet LED (“UV-LED”)* during operation of
the device. The UV-LED radiates intense ultra-violet light (“UV light”) and can be
harmful to the eyes even during a brief period of exposure.
* UV-LED means any UV-LED device or packaged UV-LEDs which emit ultra-violet
light whose peak wavelength is shorter than 400nm.
2. Always wear UV protective eyewear when handling the UV-LEDs.
3. UV light can cause skin damage, up to and including, skin cancer. Always wear
protective clothing to prevent UV-LED exposure to skin.
4. Instruct and warn all intended users of proper handling of the UV-LEDs and all
potential hazards. Always provide proper instructions, labels and warnings in
accordance, with the standards set forth by the International Electric Committee (IED).
direct exposure to the UV light on the human body,
particularly the eyes, is experienced.
5. Always keep this product out of the reach of children and other untrained persons.
6. Always adhere to safety instructions and warnings.
All UV light should be used in such a way as to ensure that no
SAVE THESE INSTRUCTION FOR FUTURE
OPERATORS TO READ
1
Work Area Safety
• Keep the work area clean and well lit.
• Do not operate the C2 Camera in explosive atmospheres, or in the
presence of ammable liquids, gases, or heavy dust. Electrical tools can create
sparks which may ignite the dust or fumes.
• Do not use the C2 Camera around corrosive chemicals. Exposure can
affect the plastic covering on the camera head and ruin the picture quality.
Personal Safety
• Stay alert, be cautious about what you are doing. Use common sense. Do not use
the C2 Camera while tired or under the inuence of drugs,
alcohol, or medications. Inattention while operating tools can result in serious
personal injury.
• Always wear eye protection. Use safety equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection for appropriate conditions.
• Use proper accessories. Do not place the camera on any unstable surface.
It may fall causing serious damage to the product or injury to a person.
• Do not over-reach. Keep proper footing and balance at all times. This leads to better control of the tool in unexpected situations.
• Never spill liquid of any kind on the video display unit. Any liquid increases the risk
of electrical shock and damage to the product.
• Do not use this device for personal or medical use/inspection in anyway.
2
The Video Display and Controller Unit
1. Shock-Resistant
Body
10. Low Battery indicator
11. 3.5” Video Screen
320 x 240 pixels
TFT LCD, 24 bit RGB
2. Power Button
3. Mini USB Port
4. Image Files
5. Image Capture
6. Directional Controller
Up, Down, Left, Right
7. Settings
8. Rubberized grip
9. 6-pin Data Cord Connection
12. SD Card Slot
13. Menu
Buttons
14. Home
Recall
15. Tab Display
16. Back Button
17. Battery
Compartment
Unit will timeout to sleep in 10 minutes, and shutdown in 20 minutes.
3
The Camera Wand and Controller
Imager Head
Camera and Lights
18.
2 White and 4
UV LED lights
19.
Camera Lens
640 x 480, 24 bit
RGB wide-angle
lens with auto-focus
& depth of eld 2cm to Innity
20.
21” Flexible
camera cable
21. UV Light
Indicator
22. Image Capture
23. Light Intensity
24. UV/White Light
Toggle Switch
4
Feature Instructions - Numbers refer to diagrams on pages 3 and 4.
1. Shock Resistant Body. Formed for durability and easy gripping.
2. Power Button. Push in to turn on and off.
3. Mini USB Port. For downloading image les to your computer via USB cable.
4. Image Files. Press to revisit images taken. Shows image number, date, & time.
Rotate. Menu button to turn image in 90 degree increments.
on side of screen denoting original top of image.
Zoom+. Each time it’s pressed, it enlarges to 2x’s, then 4x’s, then back to
original 1x size. With the image enlarged, use the Directional Controller buttons
(6) to navigate around the image.
Delete. Deletes the image on screen.
More. To secondary menu:
Transfer. With USB cable connected, it will send images to your computer.
See Page 6 for Transfer details.
Delete All. This will delete the entire catalog of images in the camera.
Press the Home button (14) to return to a live image.
5.
Image Capture. Press when the image you want is on the live screen.
6.
Directional Controller. Press the Image Files button (4) to show captured
images. Use the left and right arrows of the Directional Controller (6) to move
from image to image. Left to go backward, right to move forward.
When in the Zoom mode, it moves the images left, right, up, or down.
7. Settings. To create and change settings.
Secondary Menu. Set Date. Use Directional Controller (6) to move left and right
between day, date, and time. Use the Up and Down controls to change numbers.
When complete, press Set to nalize. Unit will automatically go back to main
screen.
revert to Default on restart. Press SET.
back to the main screen.
8. Rubberized Grip. Easy to hold, helps protect the frame from dents or
scratches.
9. 6-pin Data Cord Connection. Be careful when connecting not to damage pins.
10. Low Battery Indicator. Green bars turn red when battery is low.
11. 3.5” LCD Screen. Clean only with dry, soft cloth. May use alcohol, if necessary.
12. SD Card Slot. Push card in all the way to insert. Push again to release/remove.
13. Menu Buttons (LIVE Picture Mode).
Rotate. Button turns image 90 degrees counterclockwise each time it is pushed.
Brightness. Use controller to adjust up or down. Brightness will
Cancel will void changes and take you
Note: Orange arrow at edge of image identies original top position of image.
Zoom+. Zooms from 1x to 2x to 4x and then back to 1x each
Zoom-. In LIVE Camera mode only, will change from 4x to 2x to 1x.
Rotate. Turns image clockwise.
Note orange arrow
touch cycle.
5
14. Home Recall. Returns to the home screen.
15. Menu (Tab) Display. Press to show tabs on screen, or to turn them off.
16. Back Button. Returns to the last screen shown only.
17. Battery Compartment. The battery ts in the backside of the handle.
18. LED Lights. Both white and ultraviolet (UV) lights for a variety of uses.
19. Camera Lens. Wide angle with auto focus for sharp and clear images.
20. Flexible Camera Extension. Wound steel casing for durability and safety.
21. UV Light Indicator. Lights up when UV lights are on.
22. Image Capture. Press to capture the image shown on the video screen.
23. Light Intensity. Used for both UV and white lights. Press (+) to brighten,
(-) to darken.
24. Toggle Switch. Press to switch between using UV and white lights.
Operating Instructions
Numbers refer to diagrams of the C2 Camera.
1. Insert SD card into the Video Display Unit (VDU), (12).
2. Plug 6-Pin Data Cord (9) from wand into VDU at heel of handle.
Be careful to insert correctly with widest side up. Insert rmly.
3. Press Power Button. (2) and allow 1 minute for power up process.
In the event the VDU will not power up:
2. Check Data Cord is fully inserted, 3. Check battery is charged.
4. UV and White Lights. Use the White LED’s for normal inspection.
Use the UV LED’s for dye inspection. (24 switch)
5. Insert the camera cable into the inspection area.
6. Once the inspection area is found you may press the “Image Capture”
button (5 on the VDU or 22 on the wand handle), to capture the image.
7. Captured images can be viewed, rotated, zoomed and panned on the
VDU screen. (Images will not be captured to memory without the SD
card inserted, but will be viewable.)
8. Images can be transferred by SD card or through the USB port.
9. Upon completion of operations, disassemble the unit and store in its
case. Recharge the battery if needed.
1. Check SD Card insertion,
6
How to Transfer Pictures
Numbers refer to diagram at right.
From the SD Card: Push the card (12) inward once. It will release from
the camera. Take the card and insert it into your SD Card reader. Follow
the (*) direction below to transfer image les to your computer.
From the Camera - to a computer using Windows OS and a USB cable
(not included).
• Connect USB mini-B end of connector to the left side of the Camera (3).
• Connect the USB A connector to a USB port on the target computer.
• Press the IMAGE FILES button (4) to put the Camera in playback mode.
• Press the MORE menu key (shown on the video screen).
• Press the TRANSFER menu key. (In Transfer mode, the Camera will
appear as an external drive to the target computer.)
* Using the Windows browser, open the external drive, and copy or move
the .jpg picture les from the DCIM\100SPEC directory to the desired
location on the target computer.
• Press the STOP menu item on the Camera video screen to leave trans-
fer mode.
• Disconnect the USB cable from the Camera, and the target computer.
Camera Safety
• Do not submerse any portion of the C2 Camera into any liquid.
• Do not insert the C2 Camera wand into anything or anywhere that may
contain a live electrical charge.
• WALLS: Shut off the circuit breaker to the whole house before using
the C2 Camera to inspect inside walls that may contain live electrical
circuitry.
• PIPES: If you suspect a metal pipe could contain an electrical charge,
have a qualied electrician check the pipe before using the C2 Camera.
Ground circuits, in some cases, can be returned to cast iron pipes and
cause them to be charged.
• AUTOMOBILES: Be sure the automobile is not running during inspection. Do not get oil or gas on the imager head. Exposure to petroleumbased substances will eventually degrade the camera lens covering.
• GENERAL USE: Do not use anywhere the unit may come into exposure
with hazardous chemicals, electrical charges or moving parts. Such
situations may result in serious injury or death. Use good judgement!
7
Battery Precautions
• Remove the battery when cleaning the unit.
• Remove the battery before storing the unit for extended periods of time.
• Use only the size and type of battery specied.
• Be sure to re-install the battery correctly.
• Do not use improper replacement batteries. This will void the warranty.
• Properly dispose of used batteries. Exposure to high temperatures can
cause a battery to explode. Do not dispose of in a re. Some countries
have regulations concerning battery disposal. Please follow all applicable
regulations.
Camera Use and Care
• Do not operate the C2 Camera unless this Operators Manual has been
read and understood completely.
• Do not immerse the video display unit in water. Store in a dry place.
The camera head and cable are water resistant when the unit is
assembled, but the video display unit is susceptible to water inltration.
• Do not use the camera if condensation forms inside the lens. Place in a
dry area and let the water evaporate before operating.
• Do not use the unit if ON/OFF switch is not properly working. Any tool
that cannot be controlled with the switch needs to be repaired.
• Store spare equipment in the storage box provided.
• Maintain the C2 Camera with care. Properly maintained tools last longer,
are easier to work with and are less likely to cause injury.
• If unit is dropped, check for cracks, or other conditions that may affect the
tools operation. If damaged, have it serviced before using.
• Use only accessories that are approved by the manufacturer for this tool.
• Use CLEAN hands before turning the unit ON or OFF and before
replacing batteries.
• Protect against excessive heat. The camera should be situated away from
heat sources such as radiators, heat registers, stoves or other products that
produce heat. Do not use the unit near moving machinery or areas where the
temperature will exceed 110°F (43°C) or below 32°F (O°C).
8
Maintenance Instructions
Remove the battery from the unit before performing maintenance.
The C2 Camera has been designed to require little maintenance.
In order to maintain its performance, always follow these guidelines:
1. Handle the device with care. It is not shock-proof and should not be
banged or dropped. Treat it as a sensitive optical device. It will work longer
& with better results.
2. Always clean the imager head (camera & lights, 17 & 18) after use with a
soft cloth.
3. Use only alcohol swabs to clean connections.
4. Avoid rubbing too hard on the LCD screen. After use, wipe the display
gently with a clean, soft, dry cloth.
5. Do not disassemble this device beyond removing the wand from the
video unit. Doing so will void the warranty.
Service
• Tool service must be performed only by authorized repair personnel.
Service or maintenance performed by unqualied repair personnel could
result in damage to the tool and will void warranty.
• Do not attempt to take any pieces of this unit apart.
• Closely follow instructions for changing accessories. Changing in a way
that is improper or careless can lead to damaged connectors and faulty
operation.
• Remove batteries before cleaning. Gently clean LCD with a dry cloth.
Do not use acetone to clean surfaces.
• Stop using the unit if it starts smoking or emitting noxious fumes.
• Remove the batteries and refer servicing to qualied service personnel
under any of the following conditions:
• If liquid has been spilled or objects have fallen into product.
• If product does not operate normally by following the operating
instructions.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance.
If you have any questions regarding the service or repair of this device,
call or write to:
Sound Environmental Products, PO Box 23, Puyallup, WA 98371
Phone: 253-845-9957 M-F 8am—5pm Pacic Time.
9
Transportation & Storage
1. Avoid exposing the unit to excessive vibration or extreme hot & cold
temperatures.
2. Store the C2 Camera indoors in its case.
3. Remove the battery if unit will not be used for extended periods of time.
Service and Repair
The tool should be taken to a SEP Independent Authorized Service Center
or returned to the factory for servicing.
If you have any questions regarding the service or repair of this inspection
tool, call or write to: Sound Environmental Products,
PO Box 23, Puyallup, WA 98371 253-845-9957 - West Coast, Pacic Time
Warranty and Liability
The warranty period for this product is ONE YEAR from date of purchase.
Proof of purchase and date must accompany the product for warranty repair. BE SURE TO REGISTER your C2 Camera.
This warranty is limited to repairing or replacing, at the option of C2 Camera, any part(s) of the product which, if properly installed, used and maintained, proves upon factory examination to have been defective in materials
or workmanship within ONE YEAR from date of delivery.
C2 Camera does not warrant items that deteriorate under normal use.
In addition, C2 Camera does not warrant any instrument that has been
subjected to misuse, negligence or accident, or has been repaired or altered
by anyone other than a certied C2 Camera repair facility.
This warranty and your remedies thereunder are solely as stated in
this manual. In no event shall C2 Camera be liable for special, indirect, incidental or consequential damages, nor for any damages arising out of delay
in shipment or production.
C2 CAMERA EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXCEPT
AS PROVIDED HEREIN.
NOTE: For assistance of any kind, including help with a product under warranty, contact C2 Camera. Give full details of the difculty and include the
model and serial numbers of the product and date of purchase.
If return of the product to the factory is then deemed necessary, shipping instructions will be provided. A RETURN AURTHOIZATION NUMBER
IS NEEDED FOR ANY RETURN. If an estimate of charges for non warranty
work or other service work is required, a quote will be furnished upon
evaluation of the product. Out-of-warranty service will not be performed
without customer approval.
10
Warranty Information
Registration is required for warranty validation and service.
Register online at C2Camera.com.
You may also mail the folowing information to:
Sound Environmental Products, PO Box 23, Puyallup, WA 98371.
Your company: _______________________________________________
Your contact information: _______________________________________
Date of purchase: _____________________________________________
Serial Number: _______________________________________________
Model Number: _______________________________________________
Store where purchased: ________________________________________
11
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.