Date: 2015-June-29
Rev: www.pbteen.com Page 1 of 14
HAMPTON CONVERTIBLE LOFT BED
ASSEMBLY INSTRUCTION
Date: 2015-June-29
Rev: www.pbteen.com Page 2 of 14
WARNING: Failure to follow these warnings and assembly instructions
could result in serious injury or death. To help prevent serious or fatal
injuries from entrapment or fails:
˙Read all instructions before assembling bunk bed.
˙Before each usage or assembly, inspect bunk bed for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use bunk
bed if any parts are missing or broken.
˙DO NOT use substitute parts, Contact PBTEEN for replacement parts
and instructional literature of needed.
˙Follow the information on the warnings appearing on the upper bunk
end structure and on the carton. DO NOT REMOVE WARNING LABEL
FROM THE BED.
˙Always use the recommended size mattress or mattress support, or
both, to help prevent the likelihood of entrapment or falls.
˙Ensure thickness of mattress does not exceed 9inches and the surface
of mattress must be at least 5inches(127mm) below upper edge of
guardrails.
˙Use only mattress which is 74”-75” long and 52.5”-53.5” wide on upper
bunk.
˙Do not allow a children under 6 years of age to use the upper bunk.
˙Periodically check and ensure that the guardrail, ladder and other
components are in their proper position, free from damage, and that all
connectors are tight.
˙Do not allow horseplay on or under the bed and prohibit jumping on the
bed.
˙Prohibit more than one person on the upper bunk.
˙Always use the ladder for entering and leaving the upper bunk.
˙Use of a night light may provide added safety precautions for a child
using the upper bunk.
˙Always use guardrails on both long sides of the upper bunk. If the bunk
bed will be placed next to a wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
˙The use of water or sleep flotation mattress is prohibited.
˙If refinishing, use a non-toxic finish specified for children’s products.
STRANGULATION HAZARD-Never attach or hang items to any part of
the bunk bed that are not designed for use with the bed; for example, but
not limited to, hooks, belts, and jump ropes.
KEEP INSTRUCTIONS FOR FUTURE USE.
04-000066-3
Date: 2015-June-29
Rev: www.pbteen.com Page 3 of 14
Important Safety Instructions:
Please read all instructions carefully before assembling this bookcase.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assembly this item. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box. Place them on a carpeted or scratch-free work surface,
as this will avoid damaging parts. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until
assembly is complete.
Two people are recommended for your safety and ease of assembly.
Prior to starting this assembly, use the parts and hardware lists to identify and separate each of the
pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions
may cause the bolts to misalign during assembly.
Please use caution if using power tools to aid in assembly. Power tools can damage the hardware or
split the wood.
Part included:
A – Headboard (x2)
B – Side Rail (x2)
C – Center Slat Support (x1)
D – Slats (x1)
E – Long Guardrail (x1)
F – Short Guardrail (x1)
G – Left Inner Right Post (x1)
H – Right Inner Right Post (x1)
I – Left Right Outer Posts (x2)
J – Post Supporting Rail (x1)
K – Ladder (x1)
- TV Media
- Book Case
- Cushy Base & Cushion
Date: 2015-June-29
Rev: www.pbteen.com Page 4 of 14
Hardware included:
L – Ball Tip Allen
Key
M – Allen Bolt
N – Spring Washer
O – Flat Washer
P – Half Moon
Washer
4 x 95 x 30(mm)
5/16”x 63
x15(mm)
5/16”x13x1.5(mm)
5/16” x 15 x
1.5(mm)
5/16 ”x 30 x
8(mm)
1pc
10pcs
10pcs
10pcs
10pcs
Q – Phillips Head
Screw
R – Connector Bolt
S – Allen Bolt
T – Spring
Washer
U – Flat Washer
8 x 30(mm)
1/4”x 10 x
112(mm)
1/4”x32x13(mm)
1/4” x 10 x 1.5(mm)
1/4 ”x 12 x 1.5(mm)
28pcs
4pcs
16pcs
16pcs
16pcs
V – Phillips Head
Screw
W – Corner Bracket
X – Machine Screw
Y – Mending
Plate
Z – Allen Bolt
8 x 19(mm)
26 x 26 x 20(mm)
5/32” x 16(mm)
28 x 28 x 50 x
4(mm)
1/4”x15x13(mm)
23pcs
3pcs
6pcs
2pcs
6pcs
Za – Dowel
8 x 25(mm)
8pcs
TOOLS REQUIRED (but not included):
Phillips Head Screwdriver
Date: 2015-June-29
Rev: www.pbteen.com Page 5 of 14
Assembly Instruction Steps:
1. Using a Philip Head Screwdriver, remove the Back Panel by detaching the screws – 20x on it.
2. Insert the Dowel (Za) – (8pcs) into the pre-drilled holes of the Left Inner Right Post (G), Right Inner
Right Post (H) and Left Right Outer Posts (I) as shown below.
Loading...