PB Teen Emma Chandelier Installation Manual

Emma Chandelier
Assembly and Installation Instructions

Country of Destination: US/CN UK/EU/AUS Middle East

CAUTION:

• BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN

FUSE BOX / CIRCUIT BREAKER UTILITY BOX.

Important Safety Instructions:

• These instructions are provided for your safety . It is very important that they are read carefully and completely before

beginning the assembly and installation of this lighting fixture.

• We strongly recommend that a professional electrician install all direct wire fixtures.

• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY

A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.

• The lighting fixture is meant for indoor use. It must be connected only to 3-wire, single-phase electrical supply

systems (provided with Ground wire or equivalent protection system).

• For your safety, it is strongly recommended that two people install the lighting fixture.

• This fixture has been rated for up to four (4) 40-watt maximum Type B standard (candelabra) incandescent li ght

bulbs (not included) or four (4) 9-watt compact fluorescent light bulbs (not included). To avoid the risk of fire, do
not exceed the recommended lamp wattage.

• Use with approved PBteen Shades only, having a minimum opening diameter of 3-1/2 inches and a minimum

lamp-to-shade spacing of 2 inches.

• The lighting fixture is meant for indoor use, DRY LOCATIONS ONLY.

• Save these instructions.

WARNING:

• To r educe the risk of fire, electric al shock or personal injury, always turn off and unplug the light fixture and

allow it to cool prior to replacing the light bulb.

• Do not touch bulb when fixture is turned on. Do not look directly at lit bulb.

• Keep flammable materials away from lit bulb.

• This lighting fixture contains lead, a chemical know to the State of Cali fornia to caus e cancer, birth de fects

and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise touching thi s
light fixture.

Pre-assembly:

• Remove all parts and hardware from box along with any plastic protective packaging.

• Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or

hardware.

• For your safety, it is strongly recommended that two people install the lighting fixture.

Parts Included: Hardw are Encl os ed :
(1) Mounting Plate (D) (3) Plastic Wire Nut Connectors (A)
(1) Threaded Tube (E) (1) Green Ground Screw (B)
(1) Canopy (F) (2) Mo unt ing Sc re ws ( C)
(1) Hanging Loop (G) (4) Big Metal Balls (O)
(1) Canopy Nut (H) (1) Big Metal Bal l (P)
(1) Lock Washer (I) (1) Small Metal Ball (Q)
(1) Hex Nut (J)
(2) Closable Link with Screw Cap (K/K1)
(1) Chain (L)
(1) Fixture Loop (M)
(4) Sockets (N)

TOOLS REQUIRED (not included): Ladder, Phillips Head & Flat Blade Screwdrivers, Wire Cutter/Stripper, Pliers &
Electrical Tape.

To Adjust the Suspension Length of t he Fix t ure:

1. Note: The adjustment or shortening of the lighting fixture’s suspension length is only needed if the factory set chain
length is not appropriate for your installation. We recommend that you adjust the chain to the proper desired length
before cutting the electrical cord.

2. Determine the lighting fixture suspension length from the ceiling for the product installation, allowing the extra cord
length for the outlet junction box wire connections as noted below.

3. Pull out the fixtures 2 wire power cord and bare ground wire woven through the Chain (L).

4. The chain length may be shortened from either end, if desired, by using pliers to separate a link along a split-line
formed in each link. Use two pairs of pliers to gently pry the link apart so that a space is created large enough for the
link to be removed from the remaining chain. Use a cloth or folded piece of paper between the pliers and the link to
protect the finish of the link during bending. For longer lengths of chain to be removed, select the desired link from
either end to open and remove the length of chain. Once the chain is at the desired length, reattach the chain (if it
isn't already) to the two Closable Links with Screw Caps (K) at each end of the chain. Secure each link by tightening
the Closable Link Screw Cap (K1) (See Fig. 2). One Closable Link with Screw Cap (K) must be attached to both the
Chain (L) and Fixture Loop (M) at the top of the Pendants Body and the other Closable Link with Screw Cap (K)
must be securely attached to the other end of the Chain (L) and Hanging Loop (G).

5. Re-weave the fixtures 2 wire power cord and bare ground wire through every other loop to the top of Chain (L).

6. If needed, (depending upon final fixture hanging position from the ceiling), cut off the extra power cord length on the
2 wire cord and bare ground wire. Make sure when cutting the power cord and bare ground wire to cut them so that
they all are at least 6 inches (152.4 mm) long within the outlet junction box (J-box). Prepare the cut power cord wires
using the following steps. Use wire strippers to prepare the ends of the two wires so that there is about 1/2 inch of
exposed wire for the Plastic Wire Nut Connectors (A).