Paytec Apex 7000 User Manual
rev. AB 02/2018
APEX 7000
MDB BILL ACCEPTOR
User Guide
2
Contents
General warning ................................................................................................................................................. 3
Product overview ................................................................................................................................................ 3
Technical description .......................................................................................................................................... 3
Installation ........................................................................................................................................................... 4
Front bezel lights and diagnostic messages....................................................................................................... 5
Firmware update ................................................................................................................................................. 6
Maintenance ....................................................................................................................................................... 6
Cleaning instructions .......................................................................................................................................... 7
Dimensions ....................................................................................................................................................... 11
The information contained in this user guide is subject to change without prior notice and is not binding for
Payment Technologies S.r.l.
APEX 7000 is distributed by Paytec.
3
General warning
•
Read this guide carefully before use.
•
Before APEX 7000 is installed, check voltage compatibility with the Vending Machine.
•
The product has been designed as internal equipment.
•
Do not use in water or near liquids where it might become wet.
•
Do not use near smoke or inflammable gases.
•
Cut power before maintaining electrical and/or mechanical components.
•
Dispose of the device in accordance with environmental laws (DO NOT burn).
•
Always read labels.
•
Do not tie the system main cables or cables belonging to slave units.
•
Periodically check whether cables are correctly plugged on their connectors.
•
Cut power before maintaining and/or cleaning the unit.
•
Use a damp cloth to clean plastic elements.
Product overview
APEX 7000 is a MDB Bill Acceptor, meeting the standards required by MDB protocol.
The product is available with 200 bill- and 500 bill-stacker.
The “Escrow” function enables users to get the bill back in the case of a failed vend or when no change is
available.
The bill validation module can be removed to make cleaning operations easier. An optical anti-stringing
technology.grants the highest security.
It is possible to enable single bills quickly by toggling the DIP switches on board.
The product is equipped with pushbutton for diagnostic purposes and front bezel lights for a correct interpretation
of diagnostic signals (the number of times the lights flash corresponds to the error code).
Apex 7000 can the updated with the handheld device PRO-2.
Technical description
Operating voltage: 34V DC unstabilized (rectified and filtered)
24V DC rms (rectified)
Voltage rate: 20V DC min.; 40V DC max.
Operating currents: 180 mA (idle), 500 mA (accepting), 1,50 A (stalled)
Operating temperature: 0°C – 60°C, 90% non-condensing humidity.
Acceptance rate: > 95% including second time insertion of a rejected bill.
Acceptance speed: approx. 20 bills per minute
Sensor array: 8 Optical Sensors
Bills accepted: up to 12 bills in all four directions - up to 72 mm wide
Net weight:
2.3 lbs./1.04 kg
(with 200-bill stacker)
Stacker capacity: 200 (standard) or 500 bills
4
Installation
Apex 7000 can be configured by toggling the position of the DIP switches on the bottom of the unit.
Toggle the switches to ON or OFF position to decide which bills are to be accepted and the insertion side.
Switch 1 – 4: Enabling single bills
By toggling DIP switches 1 through 4 to ON or OFF position, you
enable or disable bills 1, 2 and 3 (in increasing order). The 4th switch
is not used.
Example: if you wish to accept only bills 1 and 2, simply toggle DIP
positions 1 and 2 to the ON position, and set 3 and 4 to OFF.
Switch 5: Limiting Acceptance Directions
To accept bills in all 4 insertion directions, toggle DIP position 5 to the
ON position. To limit acceptance to left-end, face-up only insertion, toggle
DIP position 5 to the OFF position.
Switch 6: Acceptor Enable Mode
Toggle DIP switch 5 to the OFF position
Switch 7: “Pulses Per Dollar”
Unused – must be toggled to OFF position
Switch 8: “Pulse Speed Setting”
Unused – must be toggled to OFF position
When power is given, the bill acceptor will cycle its motor and stacker. Check the bezel lighting. If the serial line
MDB is ON, the front bezel lights will be flashing.
Should the acceptor be inhibited (by a Master unit) or the serial line MDB is cut, the front bezel lights will be OFF.
FRONT BEZEL
LIGHTS
Loading...