Paxton Magstripe 25 shadow card pack User Manual
07/11/2011
1 2 3 4
+
CARDLOCK
enrolment card
1. A
t installation, present this
card to the reader to
v
alidate
the to
k
ens in this pack.
2. To re
-v
alidate a user to
k
en,
present this enrolment card
to the reader followed by the
user token.
BEEP!
BEEP!
BEEP!
BEEP!
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Master Card
1.
T
o enrol a user card, write the use
r’
s name on a paper
card, swipe it through the reade
r
, then swipe the user
card through the reade
r
.
2.
To set the door open time: swipe this card, the reader
will bee
p
,
w
ait for the required period, swipe the card
again, the bleeping will stop
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
1 2 3 4
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Swipe this card to bar:
Write name:
John Smith
Ins-30103 - Magstripe 25 shadow card pack
Adding a new pack of shadow cards (up to 4)
1. Take the master card from the original card pack.
2. Swipe the original master card.
3. Swipe the master card from the new pack you wish to enrol.
4. The new pack is now enrolled. Return both master cards to their respective packs.
- Up to 4 shadow card packs can be enrolled onto the system.
Issuing tokens
1. Write the name of the user on a shadow card.
2. Swipe the shadow card through the reader.
3. Swipe the chosen user card through the reader - it is now enrolled.
4. Store the shadow card in a safe place.
Bar a user
1 2 3 4
John Smith
Swipe this card to bar:
Write name:
CARDLOCK
User Card
John Smith
1. When a card is lost or stolen it is important to bar the card from your system to avoid unauthorized access.
2. To bar a card or token take it's corresponding shadow card from the card pack.
3. Present the shadow card to the reader. This will remove the lost card or token from your system.
4. A barred card can re-validated by presenting the enrolment card followed by the user card to the reader.
5. Alternatively a different user card can be swiped which will then pair that user card with the paper shadow card.
Fail Open release card - (Unit default = Fail Closed)
This card is used with systems where a fail open
electric release is used for the safe operation in the
event of a fire. Present the card to the reader to
drive a fail open release or a maglock. Present the
card again to revert to the fail closed operation
FUNCTION CARD
fail open release
1 2 3 4
BEEP!
BEEP!
THIS CARD CAN ONLY BE USED WITH A FAIL OPEN LOCK.
1. Take the fail open release function card from the starter pack.
2. Present/swipe the card through the reader. The reader will beep for about a second.
3. The reader is now set to fail open mode. This allows safe operation of the door in case of re: The lock will
release when the power is cut.
4. To revert to fail closed mode, swipe the card again and the reader will beep once.
Factory reset
1. Power down the unit.
2. Press and hold down the exit button.
3. Power up the unit and release the exit button. The reader will beep and the red LED will come on.
4. After 3 seconds the unit will beep 3 times again and all the LED's will come on.
To delete a card pack
1. Card packs may be deleted from the system if required. Once a card pack has been deleted another one may
be enrolled in its place.
2. To delete a card pack, take the master card and swipe it backwards through the reader. The LEDs should then
start to ash in sequence, one after the other.
3. During this phase, swipe the master card backwards again and the reader will beep once and the LEDs will all
come back on.
4. The card pack will now have been removed from the system
Compatible with any Track 2 ISO magstripe card
User cards are NOT supplied with this unit. Please supply your own user cards.
Loading...