Paxton ins-30211 Instruction Manual

ins-30211

1

Ø 5/16"

Ø 13/8"

Ø 15/16"

Paxton

≤45º

≤45º

0 11

1/41/4 3/43/4 1/21/21/43/4 1/21/43/4 1/21/4 1/4 3/41/2 1/4 3/41/2 1/4

22 33

0 11

1/41/4 3/43/4 1/21/21/43/4 1/21/43/4 1/21/4 1/4 3/41/2 1/4 3/41/2 1/4

22 33

1x

4x

1x

2x

2x

1x

1x

2x

2x

2x

2x

1x

Ø5/16" /Ø 8mm

2

43

21

1.5"

Ø1/"

38mm

2/"

2/"

Exterior

Extérieur

Ø5/16"

Ø8

mm

Ø24mm

Ø35mm

Ø15/16"

Leave at least one thread showing so the two parts
can freely turn in both directions when tted.

Laissez au moins un letage visible an que les deux
pièces puissent tourner librement dans les deux
directions une fois installé.

Deje al menos una rosca de tornillo a la vista para que
las dos partes puedan girar libremente en ambas
direcciones al ajustarse.

EN

F

ES

3

7

65

m4 x /"

m3 x /"

8

4

9

11

m4

-Don’t over tighten

-ne pas trop serrer

-no apretar demasiado

!

12

10

5

1413

15 16

m4 x 1/"

1

2

1

2

32

17

2

1

3 mm

1

2

6

32

17

2

1

3 mm

1

2

7

4

5

6

http://paxton.info/3101

8

!

+

-

9

43

2

3 mm

1

10

6

5

1..2..3

11

Standalone

43

1

2

Paxton

Paxton

1.At installati
reader to v

2.To re-v

user token

More info:

Paxton

Paxton

12

Standalone

21

5

6

Paxton

FUNCTION CARD

Enrolment card

1. At installation, present this card to the
reader to validate the tokens in this pack

2. To re-validate a user token present this
enrolment card to the reader followed by the
user token

1.At installati
reader to v

2.To re-v

user token

More info:

Paxton

Paxton

13

Standalone

65

3

4

Paxton

Paxton

14

Standalone

43

21

Paxton

FUNCTION CARD

Enrolment card

1. At installation, present this card to the
reader to validate the tokens in this pack

2. To re-validate a user token present this
enrolment card to the reader followed by the

user token

1.At installati
reader to v

2.To re-v

user token

More info:

Paxton

Paxton

15

65

Paxton

Paxton

FUNCTION CARD

Silent Operation

Present this Card to Silence the beeping noises

made by the reader. Present this card again to

renable the beeping noises.

Standalone

16

0 m

3m

15m

20m

30m

50ft

65ft

100ft

10ft

0 ft

17

xxx- xxx

≤ 50000

4 x AA Alkaline

IEEE 802.15.4

3m - 15m

900-100WT
900-100BL

900-200WT
900-200BL

-20°C +55°C

≤ 10 mm

10 ft - 65 ft

-4°F +131°F

-0°C +49°C

-32°F +120°F

35 - 57 mm

IP55

6V

800mA

18

[phone]

paxton.support

[e-mail]

877.438.7298

usapaxton.support

[e-mail]

[phone]

paxton.benelux.support

[e-mail]

[phone]

paxton.benelux.support

[e-mail]

[phone]

paxton.gmbh.support

[e-mail]

[phone]

[e-mail]

paxton.support

[phone]

[e-mail]

paxton.support

8000 3570 3783

paxton.support

[e-mail]

[phone]

paxton.soporte

[e-mail]

[phone]

paxton.soporte

[e-mail]

[phone]

paxton.support

[e-mail]

19

The declaration of conformity is available on request. Contact details are provided at:

http://paxton.info/596

These products are not suitable for retail sale. All warranties are invalid if these products are not installed
by a competent person.

Parts of this product are Copyright (c) 2013-2015 Atmel Corporation. All rights reserved. Redistribution and use in source and binary forms,
with or without modication, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the docu­mentation and/or other materials provided with the distribution.

3. The name of Atmel may not be used to endorse or promote products derived from this software without specic prior written permission.

4. This software may only be redistributed and used in connection with an Atmel microcontroller product.

THIS SOFTWARE IS PROVIDED BY ATMEL “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE EXPRESSLY AND SPECIFICALLY
DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (IN­CLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.

20

Ce dispositif est conforme à la section 15 du règlement de la FCC. Le fonctionnement est soumis aux deux conditions
suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif doit accepter toute interférence
reçue, y compris des interférences qui peuvent causer un fonctionnement non souhaité. Tout changement ou modi­cation non agréé par la partie responsable de la mise en conformité peut entraîner une interdiction d'utilisation de
l'équipement.

Conformité et limitations du produit

Les méthodes de câblage doivent être en accord avec le code nation électrique (ANSI/NFPA70), codes locaux et les au­torités ayant la juridiction.

Ce dispositif est conforme au(x) standards RSS de l'industrie Canadienne sans-licence. Le fonctionnement est soumis aux
deux conditions suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif doit accepter
toute interférence reçue, y compris des interférences qui peuvent causer un fonctionnement non souhaité.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by the party respon­sible for compliance could void the user's authority to operate the equipment.

Product compliance and limitations

Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities
having jurisdiction.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORD­ING TO THE INSTRUCTIONS.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including inter­ference that may cause undesired operation of the device.

http://paxton.info/1606

21

22

© Paxton Ltd 1.0.0

Made in the UK