Paxton PROXIMITY P series, 353-110-US, PROXIMITY P50, 373-120-US, 373-110-US Instruction Manual

03/09/2009

Ins-40002-US PROXIMITY P series reader - UL

Technical Support

1.800.672.7298 [e-mail]

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

Mounting

Paxton

P75 Screw connector option

NOTE: The unit should be mounted in conjunction
with an electrical backbox to achieve the required
clearance for the connector.

If an adaptor plate (310-750-US) is tted, the

mountings on the backbox can also be used.

This unit is for Indoor use only

This reader is designed to read EM4100 tokens. It will provide Clock and

Data output for Paxton (Net2 / Switch2).

PAGE 1

Red 12v dc

Brown

Orange

Green

Yellow

Blue

Mauve

Black/White

Brown

Yellow

Reader 1

Orange

Keypad 1

+12v

0v

N.C.

N.O.

Com

N.C.

N.O.

Com

Alarm Output

0v

Contact

0v

Exit

0v

Tamper

PSU

Rx

Tx

Relay 1

Relay 2

Exit

Contact

Tamper

PSU

OK

5v

12v

Red

Brown

Orange

Green

Yellow

Blue

Mauve

Black/White

Brown

Yellow

Orange

Reader 2

Keypad 2

Power

Relay 1Relay 2Inputs

Network

CAT5 cable coding

White/Green

Green

White/Orange

Orange

1

2

3

4

Screen or spare cores
from network cable

CAUTION: for 12v d.c. readers only. For

correct connection of old 5v readers, refer to

instructions.

Serial number

241821

Test ID: 012345678901

z-1440

3 24898 00000 4

xR

Green

White/Green

1

Screen or spare cores from
network cable

White/Orange

3

Orange

4

K1 redaeR da

pye 1

12V

Alarm Output

R leay 2

N.C.

N.O.

Com

N.C.

N.O.

Com

0 V

0V

Exit

0 V

PSU

0V

Contact

Tamper

R leay 1

V2

1

V

5

KO

T ep
ma

r

tcatnoC

t

i

xE

R leay 1

xT

U

S

P

Keypad 2 Reader 2

stupnI

P ewo r

R le
a

y
2

CA

nidoc

e

lbac

5T g

kr

ow

teN

+V out

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

0V out

Data

Load

Clock

tu

o V+

DEL deR

DEL

re

bmA

DEL neerG

0D/ata

D

1D/kc

olC

tceteD

aideM

tuo V0

ataD

daoL

kcolC

Net2

2

Suitability

Security sensitive doors

Mounted on metal surface

Wiring

Wet environments

12V

Red 12V

Red LED

Brown

Amber LED

Orange

Green LED

Green

Yellow

Data/D0

Blue

Clock/D1

Mauve

Media Detect

Black

0V

Contact

n

o

C

Exit

xit

E

Card reader or keypad

tact

Switch2

S

witch

2

C
ard

er
w

read

Po

Control

er or

unit

ay

keyp

ad

oor rel
D

Inputs

CAU

TIO

:

N

Inp

CAUTION: For 12V d.c. readers

readers o

n

u

only. For corr ect connection of old

ts

nnectio

co

n

readers, re fer to instructions .

refer to in

stru

Readers mounted together

Net2 control unit

ell

B

Bell

larm
A

V

2

1

Alarm

l
of old

Fo
y.

PowerDoor relay

r 1

2V

For correct

rea

ctions.

12v

V

0

0v

.

.C

N

N.C.

.

N

O.

N.O.

M

O

C

Com

.c.

d

ders,

Switch2 control unit
(not evaluated by UL)

12 inches

between

readers

Part number Description

353-110-US PROXIMITY P50 reader

373-110-US PROXIMITY P75 reader

373-120-US PROXIMITY P75 reader - screw connection

Cable extensions

Use Max length Type

Reader / Keypad 500 feet 8 core, shielded - Belden 9538, Alpha 1298C (22AWG) or equivalent

NOTE: Where selected, any equivalent cabling / wire must be ' UL Listed '

Options

Cable Specication

All interconnecting devices must be UL Listed.

PAGE 2

Fitting Kit

Option Part number Description

P50 Fitting Kit fk1-085 (5) Cable clips

(3) No6 x

(3) Wall plugs 22 mm

(1) 8 mm x 3 mm small self tapping screw - zinc

P75 Fitting Kit fk1-084 (5) Cable clips

(3) No8 x 1 woodscrew - zinc

(3) Wall plugs 35 mm

(1) 8 mm x 3 mm small self tapping screw - zinc

3

/4 woodscrew - zinc

Unit installation / test

When chosing a location for the reader, ensure that it is a least 12 inches from other readers. This will include

readers mounted on the other side of the same wall as the radio signal will cause interference and reduce the read

range. The reader should not be used on metal surfaces as the reected signal will also reduce the read range.

Standard Unit - Drill a hole in the surface for the rear data cable. Secure the unit to the surface with three screws

as per tting diagram on page 1. 3 suitable screws and xings are provided for tting the unit to a wall. Ensure

the data cable has free access at the rear.

A choice of black and white covers are also provided. Hook the required cover over the top of the reader, press
home at the bottom and secure with the single xing screw.

Screw Terminal Unit - The adapter (310-750-US) is mounted to a standard backbox using the xing screws
provided. The 75mm reader is then mounted onto the adapter using the tting kit provided with the reader.

The reader will bleep and all the LEDS should display after powering on the control unit. Presenting a user card to
the reader will cause the LEDs to briey change to a single Green or Red LED.

Check the following FAQs section for assssistance if any problems are encountered.

Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70),
local codes, and the authorities having jurisdiction.

Maintenance

Following the completed installation of this equipment, no further maintenance or testing is required.

It is advisable to ensure that any third party backup power supplies or recovery procedures are checked regularly
to ensure that the operation of the Paxton system is not compromised.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modications not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.

PAGE 3

Technical Help

Here is the list of topics about this product that receive the most technical support inquiries.

We list them here to help you speed up the installation and trouble shooting process.

1 - Readers/Keypads not working.

Q- Software settings - Conrm that the settings of the reader or keypad are correct.
Q- Connections - Check the wiring and integrity of the connectors. If possible, test this reader on the other port.
Q- Extended cable - Belden 9538/9540 should be used up to a maximum of 500 feet. Twisted pair alarm cable should
Q not be used. To conrm that an extended reader cable is not at fault, wire the reader directly to the port.
Q- Supply voltage - Conrm that the voltage is within specication. (see table)
Q- User token - Conrm that the user token used for testing is OK by presenting it to a known working reader.
Q- Interference - Conrm whether the reader works when tested 'in hand' and not mounted on the wall.
Q PROXIMITY readers should not be mounted back to back or close to other RF devices.

2 - Readers / Keypads - Extending cable.

QOnly Belden CR9538 / 9540 or a UL equivalent can be used for cable extensions. The maximum run is 500 feet.

3 - Net2 - Using a door reader as a desktop reader.

QIt is possible to congure a door reader to operate as a desktop reader:
Q1 - Select the doors menu in the left hand Net2 pane.
Q2 - Click on the door you wish to change the reader to act as a desktop reader.
Q3 - Under the relevant reader tab, change the reader operating mode to 'Desktop Reader'.
Q4 - The PC displays 'Would you like to accept desktop reader events from this reader at the PC?' ; click 'Yes'
Q Now when you present a blank or existing token to that reader it will allow you to add this new token or edit
Q the existing one.

NOTE:QRemember to return the operating mode to the original setting once the cards have been read

Q or users will not be able to gain access through the reader.
Q KP Reader - Ensure that Keypad type is set to 'None', otherwise the Desktop reader option will not be available.

4 - Net2. What to do if a user has no access - Check the reader LED's when a card is shown.

Q- No LED's - the reader has no power.
Q- No change in display - try the card on a known working reader. If there is still no response, replace the card.
Q- Green LED ashing when a card is presented; check relay 1 LED to check for activity and also the lock wiring.
Q- Red LED is ashing when a card is presented; check the validity of the user at the PC.
Q Check user's access level and ensure they should have access by clicking on Current Validity.
Q Check the 'Expires end' date and conrm this has not been past.
Q- Reinstate the ACU from the doors screen. Select the ACU's you wish to reinstate and then click OK.

Specications

Environment

Operating temperatures - all items

Waterproof - P50 and P75 IPX7

Waterproof - P75 - screw connection option

Cable length

Electrical

Voltage

Current

Carrier frequency

Clock and data bit period

Dimensions

P50

P75

Read Range

P50

P75

Min

-35 °C ( -31 °F )

Min

Width

2 inch 4 inch

3 inch 5

Token

3 inch 2 inch

4 inch 2

+66 °C ( + 151 °F )

Max

Outdoor Use

Indoor Use

10 feet

Max

12V DC

130 mA

125 kHz

600 µs

Height

1

/

2 inch

Keyfob Hands Free Token

1

/

2 inch

Depth

5

/

8 inch

5

/

8 inch

4 feet

5 feet

PAGE 4