PAX Technology PX5BW User Manual

PAX TECHNOLOGY INC.

Product Description

Stylus pen

Touch screen

and

Contactless

reader area

Magnetic

stripe reader

Privacy shield

Keypad

Smart card

reader

Cable retention

cover plate

Communication

ports - located

under cover plate

Speakers

Regulatory label

Part number/

serial number label

Communication

module

MAC address label

Communication ports are labeled and color-coded:

White Red Yellow BlackGreen Blue

PAX TECHNOLOGY INC.

Communication Module

P terminals that include a default communication module come

standard with one Ethernet port and RS232, USB, and PUSB

network capabilities. However, if the default communication

module is replaced with an optional communication module,

your choice of these additional network capabilities are

available:

• A second Ethernet port

• Power over Ethernet

• An Ethernet hub

The communication module is located on the underside of

the terminal.

WARNING:

Power down and remove all power from the terminal before

removing or installing a communication module. A

communication module must be installed before power can be

applied to the terminal.

• Wi-Fi and Bluetooth LE

• Wi-Fi and Cellular GSM

Communication

module

Power Connections

Power can be supplied via the power port or a single data cable

that carries power. This power can be provided via a “powered

cable” where the connected POS terminal provides the power

(i.e. PUSB or Power over Ethernet) or by connecting a P power

supply directly to the data cable (i.e. RS232 or USB).

1) Power Port

Insert the power connector into the green POWER port. Turn

the power connector, locking the tab behind the short plastic

wall. Dress the cable through the retention clips. A separate

data cable is also required.

2) POS Cable

Insert the cable connector into the appropriate port on the

terminal. Dress the cable through the retention clips opposite

the port. Connect power supply to cable as required. The cash

3) Power over Ethernet (PoE)

Power is available over the red LAN1 port when the optional

PoE communication module is installed.

Cable Retention Cover Plate

After power and data cables are

connected and dressed through

retention clips, install the cable

retention cover plate and secure

with captive screw.

Working Environment: Temperature -10°C～50°C (14°F～122°F)

R.H.: 10%～93% (non-condensing)

Storage Environment: Temperature -20°C～60°C (-4°F～140°F)

R.H.: 5%～95% (non-condensing)

Screw

PAX TECHNOLOGY INC.

Stylus Holder and Pen

Mou nting

Loc ation s

2)Stylus P ort

Privacy Shield

Ret entio n

Cli ps

Privacy Shield

1) Align stylus holder over

metal screw openings at left

side or top of terminal. Insert

tabs into indentations along

edge. Attach with captive

screws.

2) Insert connector end of

stylus pen into stylus port on

left side of terminal.

3) Use enclosed plastic card to

press stylus cord into retention

clips on left side of terminal.

Insert tabs and snap shield firmly in place

to left and right of keypad. Not designed to

be removable. Removing the shield breaks

the retention tabs and the ability to remotely

track the status of the shield is lost.

Decorative Plug – If a privacy shield is not

installed, a non-removable decorative plug

may be installed in its place. This plug does

not provide any PIN entry privacy.

CAUTION: If the privacy shield is not installed,

you must use PCI-approved alternative methods

to secure the PIN pad.

1Privacy Shield

Decorative Plug

Plugs

1) Stylus Holder Plug

If required, to prevent stylus pen from

being inserted vertically into stylus

holder, firmly insert plug into opening

in holder, aligning with curve of stylus

holder.

2) Smart Card Reader Plug

If required, insert smart card reader

plug into smart card receptacle slot.

To remove, if required, gently pry out

the plug using a small screwdriver in

the slit along top of plug.

3) Ethernet Plug

An Ethernet plug is included in case

you want to block an inactive LAN port.

Align plug so that it matches the shape

of the port and gently push into opening.

To remove, if required, gently pry off

using a small screwdriver in the slit

along the top of the plug.

Note: LAN2 port is enabled only when

Ethernet hub or PoE and Ethernet hub

communication module is installed.

3) Et herne t

Plu g

1) Stylus

Holder

Plug

2) Smart Card Reader Plug

PAX TECHNOLOGY INC.

Reset Button and Audio Jack

If required, restart the

terminal by pressing in

and holding the reset

button for 2-3 seconds

If required, a visually disabled person can connect a

headphone to the terminal for audio prompting using the

3.5mm output audio jack.

Cable Lock

If required, insert customer-provided

cable lock into K-Slot®. Loop cable

around permanent object to secure

in place.

Reset

Button

Stylus Port

Audio Jack

Stand Installation

If required, the P terminal may be

mounted to a stand.

Instructions may vary depending

on stand specifications.

Carefully route the required cables

up through the stand pipe and out

the top. Connect the cables to the

Pterminal ports.

Insert the three mounting slots on

the underside of the terminal into

the three metal prongs on the stand

base.

Slide the terminal firmly into position,

locking the terminal in place on the

stand. Secure with fastening screw

or locking device as required.

Route

Cables

Mounting

Slots

P/N:200312000000224

This document is provided to you for informational purposes

only. All features and specifications are subject to change

without notice. PAX's name and PAX's logo are registered

PAX Technology Inc.

4901 Belfort Road, Suite 130

Jacksonville, FL 32256, USA

T: 877-859-0099

W: www.pax.us

E: sales@pax.us

PAX TECHNOLOGY INC.

Cleaning the Device

WARNING:

Do not use industrial strength or abrasive cleaner as it may

damage or scratch the screen.

Do not immerse device in water (or liquid.)

Do not spray water or cleaner into the MSR slot, Smart Card

Reader or ports.

To clean screen, apply distilled water or mild glass cleaner

onto a soft, lint-free cloth and gently wipe terminal screen.

To clean terminal, apply distilled water or plastic-safe cleaner

onto a soft, lint-free cloth and gently wipe terminal.

Available Accessories

RS232 Cable

200204020000140

Requires Power Supply

USB Cable

200204020000141

Requires Power Supply

Power Supply

200310110000070

Requires Power Cord

Stylus Pen

200209090000929

Privacy Shield

200209060000040

Power Cord

200311020000023

Requires Power Supply

Stylus Holder Plug

200209090000930

Decorative Privacy

Shield Plug

2002090900001037

FCC Regulations:

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

This device has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiated radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and

receiver.

-Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV

technician for help.

Caution: Changes or modifications not expressly

approved by the party responsible for compliance could

void the user's authority to operate the equipment.

RF Exposure Information

This device meets the government's requirements for

exposure to radio waves.This device is designed and

manufactured not to exceed the emission limits for

exposure to radio frequency (RF) energy set by the

Federal Communications Commission of the U.S.

Government.

This device complies with FCC radiation exposure limits

set forth for an uncontrolled environment. In order to

avoid the possibility of exceeding the FCC radio

frequency exposure limits, human proximity to the

antenna shall not be less than 20cm (8 inches) during

normal operation.

PAX TECHNOLOGY INC.

PAX Technology PX5BW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual