PAX Technology E800 Users Manual

1. Contents Checklist
Name
Qty.
1
AC Power Adapter
1
AC Power cable
1
Thermal Paper Roll
1
Product Manual
1
Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual,ect.,pl ease contact the dealer.
2. Product Description
3.Installtion
USB port: Connect USB device.
Micro USB port: Connect Micro USB device.
Serial Port: Connect serial device.
SIM card slot: Open the SIM card/SD card cover and insert the SIM card in to the
corresponding SIM card slot.
Micro SD card slot: Open the SIM card/SD card cover and insert the Micro SD card in to the
corresponding Micro SD card slot.
WAN port: Open the wire hidden cover at the back of the terminal, insert the cable which is
connected to the Internet into the WAN port to
provide wired network for the cash register.
LAN port: If the WAN port has been connected to the Internet, then the LAN port can
provide network connection.
Cash drawer interface: Open the wire hidden cover at the back of the terminal, insert the
cash drawer's port into the cash draw er interface on the cash register, so that th e cash
drawer is connected with the cash
register.
Audio Jack: Use international standard interface.
4. Instruction
Power ON/OFF Power on: Press and hold the Power button (on the side) for three seconds until
the main screen displays normally. Power off: Press and hold the Power button (on the side) for three seconds until
the shutdown menu appears, tap “Shutdown”, and then shutting...”appears. The
terminal will be turned off after a few seconds. Load the print paper: When the printer's Out of Paper indicator lights in yellow, it needs to load the print paper. Open the external printer cover by pulling it outward with fingers from the printer cover opening. Open the built-in printer cover by pressing inward the spring key. Load the paper roll by following the direction as shown in the paper warehouse, and close the printer cover. Then the indicator will light off.The paper is changed successfully. Open the external printer cover by pulling it outward with fingers. Then Magnetic Stripe Card: Place the magnetic stripe face down (keep the magnetic stripe card perpendicular to the main display), swipe card through the magnetic card slot at a constant speed. IC Card: Place the IC chip facedown, insert the IC card into the card slot, and push it to the end. Contactless card: Put the contactless card on the center of the payment modulescreen.
5. Specification
Operation System: Android 6.0
CPU: Quad-coreA17,1.8GHZprocessor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6inch,resolution:1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: Built-in speaker, support headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
code scanning
L-Sensor (Ambient Light Sensor): automatically adjust the backlight
brightness of the main
display
Wireless Communication: Support LAN, WIFI, Bluetooth,
3G/4G(optional)
Peripheral Ports: 1 Micro-USB port
5 USB ports
3 Network ports(1 WAN port, 2 LAN ports)
1 cash drawer
1 serial port
1 audio jack
Card Slot: 1 SIM card slot
1 Micro SD card slot
1 magnetic stripe card/IC card slot, using two-in-onesupport MAG&ICC
Magnetic Card Reader: Support track 1/2/3.
IC Card Reader: Conform to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
6. Paper Installation
1. When the printer is out of paper, the Out of Paper indicator will light in yellow. Open the
external printer cover by pulling it out ward with fingers from the printer cover opening(that the arrows poi nt to).
2. Open the built-in printer cover by pressing inward the spri ng key(that the arrow points to).
3. Open the built-in and external printer covers as shown in the figure.
4. Load the paper roll and make sure a part of paper is exposed.
5. Close the pri nter covers in turn. The Out of Paper indicator will light off. The paper is changed success fully.
7. Cautions of Installation and Usage
1Avoid exposing the terminal in hot, humid,dusty or strong electromagnetic environment. 2Do not violently vibrate, shake or beat the product. 3Do not plug/unplug any units of the product when it is power on, otherwi se it may
damage the internal circuit. 4Do not maintain the terminal if you are non-professional 5Before inserting the magnetic stripe/IC/contactless card, please check whether there is any foreign object inside or surround the card slot , and if any , report to related personnel.
FCC Regulations:
This device complies with Part 15 of the FCC Rul es. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any i nterference received, including interference that may caus e undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi cations. However, there is no guarantee that interference will not occur in a particular installation. If thi s equipment does cause harmful interference to radio or tel evision reception, which can be determined by turni ng the equipment off and on, the user is encouraged to try to correct the i nterference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equi pment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authori ty to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equi pment should be installed and operated with minimum distance 20cm between the radiator & your body.
ISED Notice
This device compli es with Industry Canada l icense-exempt RSS s tandard(s). Operation is
subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Indus trie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doi t accepter tout brouillage radioél ectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device compli es with RSS-310 of Indus try Canada. Operation i s subject to the condition
that this device does not cause harmful interference.
Cet appareil est conforme à la norme RSS-310 d'Industri e Canada. L'opération est soumise à
la condition que cet appareil ne provoque aucune interférence nuisible.
This device and its antenna(s) must not be co-l ocated or operating in conjunction wi th any
other antenna or transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être si tués ou fonctionner en conjonction avec
une autre antenne ou un autre émetteur, exception faites des radi os intégrées qui ont été testées.
The County Code Selection feature is di sabled for products marketed in the US/ Canada. La fonction de sélection de l'indi catif du pays est désactivée pour les produits
commercialisés aux États-Unis et au Canada.
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equi pment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations: Cet équi pement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps .
Loading...