PAX Technology A930 User Manual

Installation Manual

A930 Wireless POS Terminal

PAX TECHNOLOGY LIMITED

Name

Qty.

Wireless POS Terminal

1

AC Power Adapter

1

USB Cable

1

Battery

1

Product Manual

1

1. Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if
there is a page missing from the product manual,ect.,please contact the dealer.

2. Installation

USB port: Connect USB device or PC.
SAM/SIM card:

○1Open the battery cover on the bottom of the terminal;

○2Take out the battery;

○3Insert SAM/SIM card into the corresponding SAM/SIM card slot.

Micro SD card:

○1Open the battery cover on the bottom of the terminal;

○2Take out battery;

○3Insert Micro SD card into the corresponding Micro SD card slot.

3. Instruction

1）Power ON/OFF
Power on: press and hold the Power button for five seconds until the LCD besides the,
and then the terminal is being turned on.
Power off: press and hold the Power button for three seconds until the shutdown menu
appears, tap Shutdown > Click Shutdown, and then “Shutting…” appears, the
terminal is being turned off.
2）Magnetic Stripe Card
Place the magnetic stripe face left, swipe card through the magnetic card slot at a
constant speed, which could be bi-directionally.
3）IC card
Place the chip face down, insert the IC card into the IC card slot, and push it to the
end.
4）Tearing off paper
Tear the printing paper toward the 45 degree direction of the paper cutter.

5) Battery charging

User can charge the battery with power adapter, and the charging status will be
displayed on the LCD.
6）Swiping contactless card
Place a contactless card close to the sensor area of swiping which is at the top of the
terminal.

4. Installation and Usage Tips

1）Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty
environment.
2）Forbid non-professional to repair the terminal.
3）Before insert the card, please check internal and around of IC card slot. when you

found some suspicious objects , must report to related administrator.

5. Lithium Ion Battery Usage Tips

WARNING:
1）Don't use the battery in sunlight or smoke, dust environment.
2）Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire.
3）If battery is impressive, deformed, damaged or exothermic seriously, please stop
using immediately and replace it!
4）If the continuous working time is only half of new one, the battery life may be end.
Please replace it!
5）Must use the specified battery model and charger, otherwise there will be explosion
6）Charging time can not exceed 24 hours. If the battery is out of power, please
recharge in time. Avoid damaging the battery in over-charge and over-discharge.
7）If be non-use for long time, please recharge the battery per 6 months to avoid
shortening its life.
8）Suggest to replace it when the battery have been used for 2 years.
9）Be sure to follow the instructions to dispose the wasted batteries.

Caution

Risk of explosion if battery replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment

type A930 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address：

http://www.pax.com.cn/ProductCE.aspx

Icon shows

Do not throw away, need professional recycling.

Class II Equipment

For indoor use only

Energy Efficiency Marking

AC voltage

DC voltage

The MAINS plug is used as the disconnected device.

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This device has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiated radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for

compliance could void the user‘s authority to operate the equipment.

FCC RF Exposure Information (SAR)

This device is designed and manufactured not to exceed the emission limits for exposure

to radio frequency (RF) energy set by the Federal Communications Commission of the

United States.

During SAR testing, this device is set to transmit at its highest certified power level in all

tested frequency bands, and placed in positions that simulate RF exposure in usage near

the body. Although the SAR is determined at the highest certified power level, the actual

SAR level of the while operating can be well below the maximum value. This is because

the device is designed to operate at multiple power levels so as to use only the power

required to reach the network. In general, the closer you are to a wireless base station

antenna, the lower the power output.

The exposure standard for wireless employs a unit of measurement known as the Specific

Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.

The FCC has granted an Equipment Authorization for this model device with all reported

SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR

information on this model device is on file with the FCC and can be found under the

Display Grant section of www.fcc.gov/oet/ea/fccid after searching on

FCC ID: V5PA930

For this device, the highest reported SAR value for usage near the body is 1.18 W/kg.

While there may be differences between the SAR levels of various devices and at various

positions, they all meet the government requirement.

ISED Notice

This device complies with Innovation, Science and Economic Development Canada

license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présentappareilestconforme aux CNR Innovation, Sciences et

Développementéconomique Canada applicables aux appareils radio exempts de licence.

L'exploitationestautorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le

brouillageest susceptible d'en

IC: 11689A-A930

ISED Radiation Exposure Statement

This EUT is in compliance with SAR for general population/uncontrolled exposure limits in

ISED RSS-102 and had been tested in accordance with the measurement methods and

procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must

not be co-located or operating in conjunction with any other antenna or transmitter.

Cetappareilestconforme aux limitesd'exposition DAS incontrôlée pour la

populationgénérale de la norme CNR-102 science de l’innovation et le

développementéconomique Canadaet a ététesté en conformité avecles méthodes de

mesure et procéduresspécifiéesdans IEEE 1528 et IEC 62209.Cetappareil et

saousesantennes ne doiventpas êtreco-localisésoufonctionner en conjonction avec tout

autreantenneoutransmetteur.

RSS-247Chapter 6.4

The device could automatically discontinue transmission in case of absence of information

to transmit, or operational failure. Note that this is not intended to prohibit transmission of

control or signaling information or the use of repetitive codes where required by the

technology.

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

In addition, high-power radars are allocated as primary users (i.e. priority users) of the

bands 5250–5350 MHz and 5650–5850 MHz and that these radars could cause

interference and/or damage to LE-LAN devices.

L'appareilpeutinterrompreautomatiquement la transmission en casd'absenced'information

à transmettreoud'échecopérationnel. Ilest à noterquecela ne vise pas à interdire la

transmission de données de contrôleou de signalisationoul'utilisation de codes

répétitifslorsque la technologiel'exige.

-le dispositif de fonctionnementdans la bande 5150 – 5250 MHz n'estutiliséqu'àl'intérieur

pour réduire les risquesd'interférencesnuisibles pour les systèmes mobiles par satellite à

cocanal;

En outre, les radars de haute puissance sontattribués en tantqu'utilisateursprincipaux

(c.-à-d. utilisateursprioritaires) des bandes 5250 – 5350 MHz et 5650 – 5850 MHz et

queces radars pourraient causer des interférences et/ouendommager les dispositifs

LAN-le.

P/N:200312000000336

PAX TECHNOLOGY LIMITED reserves the right to change

product technology specifications without notifying.

PAX TECHNOLOGY LIMITED

Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road,
High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: [phone] Fax: [phone]
Website: http://www.pax.com.cn
Responsible Party: PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville ,
Florida, 32256
Nikolai Francis
T: [phone]