A910 Smart Mobile Payment Terminal
Name
Qty.
A910 Smart Mobile Payment Terminal
1
AC Power Adapter
1
Battery
1
Cable
1
Product Manual
1
1. Contents Checklist
Please check the components after unpacking. If any one of them is missing, or if there is a page
missing from the product manual,etc.,please contact the dealer.
2. Installation
USB port: Connect USB devices or PC.
SAM/SIM card:
1
○
Open the battery cover on the Top of the terminal;
2
○
Take out the battery;
3
○
Insert SAM/SIM card into the corresponding SAM/SIM card slot.
Micro SD card:
1
○
Open the battery cover on the Top of the terminal;
2
○
Take out battery;
3
○
Insert Micro SD card into the corresponding Micro SD card slot.
3. Instruction
1） Power ON/OFF
Power on: press and hold the Power button for five seconds until LCD backlight light, the terminal
turns on successfully.
Power off: press and hold the Power button for three seconds until the shutdown menu appears,
tap Shutdown > Click Shutdown, and then “Shutting…” appears, the terminal is being turned
off.
2） Magnetic Stripe Card
Place the magnetic stripe face left, swipe card through the magnetic card slot at a constant
speed, which could be bi-directionally.
3） IC card
Put IC card chip side upward and the magnetic stripe face down, then push-in Card slot of bottom.
4) Tearing off paper
Tear the printing paper toward the 45 degree direction of the paper culter.
5) Battery charging
User can charge the battery with power adapter, and the charging status will be displayed on the
LCD.
6）Swiping contactless cardg
Place a contactless card close to the sensor area of swiping which is at the top of the terminal.
Working Environment Temperature: 0℃～50℃(32℉～122℉)
Humidity: 10%～93%( non-condense)
Storage Environment Temperature:-20℃～70℃(-4℉～158℉)
Humidity.:5%～95% (non-condense)
4. Installation and Usage Tips
1）Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
2）Forbid non-professional to repair the terminal.
3）Before insert the card, please check internal and around of IC card slot. when you found some
suspicious objects , must report to related administrator.
5. Lithium Ion Battery Usage Tips
WARNING:
1）Don't use the battery in sunlight or smoke, dust environment.
2）Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire.
3） If battery is impressive, deformed, damaged or exothermic seriously, please stop using
immediately and replace it!
4）If the continuous working time is only half of new one, the battery life may be end. Please
replace it!
5）Must use the specified battery model and charger, otherwise there will be explosion
6）Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time.
Avoid damaging the battery in over-charge and over-discharge.
7）If be non-use for long time, please recharge the battery per 6 months to avoid shortening its life.
8）Suggest to replace it when the battery have been used for 2 years.
9）Be sure to follow the instructions to dispose the wasted batteries.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
FCC RF Exposure Information (SAR)
This device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of the
United States.
During SAR testing, this device is set to transmit at its highest certified power level in all
tested frequency bands, and placed in positions that simulate RF exposure in usage near
the body. Although the SAR is determined at the highest certified power level, the actual
SAR level of the while operating can be well below the maximum value. This is because
the device is designed to operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output.
The exposure standard for wireless employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
The FCC has granted an Equipment Authorization for this model device with all reported
SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR
information on this model device is on file with the FCC and can be found under the
Display Grant section of www.fcc.gov/oet/ea/fccid after searching on
FCC ID: V5PA910
For this device, the highest reported SAR value for usage near the body is 1.01 W/kg.
While there may be differences between the SAR levels of various devices and at various
positions, they all meet the government requirement.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en
IC: 11689A-A910
ISED Radiation Exposure Statement
This EUT is in compliance with SAR for general population/uncontrolled exposure limits in
ISED RSS-102 and had been tested in accordance with the measurement methods and
procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must
not be co-located or operating in conjunction with any other antenna or transmitter.
Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population
générale de la norme CNR-102 science de l’innovation et le développement économique
Canada et a été testé en conformité avec les méthodes de mesure et procédures
spécifiées dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent
pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou
transmetteur.
PAX TECHNOLOGY LIMITED reserves the right to change
product technology specifications without notifying.
PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road,
High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630 Fax: 0755-86169634
Website: http://www.pax.com.cn
Responsible Party: PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville ,
Florida, 32256
Tony Fernandez
+1 623-640-9529
Loading...