Patton electronics SmartNode 4634 series, SmartNode 4638 Series Quick Start Manual

SmartNode 4634 and 4638 Series

VoIP Gateway Routers

Quick Start Guide

Approval

over BRI/S0-ISDN interfaces.

Zulassung

BRI/S0-ISDN Schnittstellen.

Aprobación Approbation

BRI/S0.

Document Number: 13221U7-001 Rev. B Part Number: 07MSN4630-QS

Revised: November 17, 2008

—This device is approved for connection to the public ISDN telecommunication network,

—Zugelassen für die Anschaltung an das öffentliche ISDN Telekommunikationnetz an

—Este aparato está aprobado para conexión a red publica ISDN sobre interfaz BRI/S0.

—Cet appareil est approuve pour la connexion au reseau ISDN public avec les interfaces

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

WARNING

•

This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualiﬁed service personnel.

•

Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are connected. The mains outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker.

•

Ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

•

For units with an external power adapter, the adapter shall be a listed Limited Power Source.

•

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is ON or OFF. To avoid electric shock, use caution when near WAN ports. When detaching the cables, detach the end away from the device ﬁrst.

•

Do not work on the system or connect or disconnect cables during periods of lightning activity.

1.0 Power up the SmartNode

1.

Connect the SmartNode to the mains (AC) power source with the power cable.

2.

Wait until the

Power

LED stops blinking and remains constantly lit. Now the SmartNode is ready

to conﬁgure.

2.0 Connecting the SmartNode to your laptop PC

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, ﬂammability, and mechanical serviceability.

CAUTION

2

SmartNode 4634 & 4638 Quick Start Guide

Laptop PC

Straight-through wired cable

LAN (ETH 0/1)

1.

Connect the PC’s Ethernet port to

Figure 1.

LAN (ETH 0/1)

Connecting to the PC

port of the SmartNode 4630. The SmartNode 4630 Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through Ethernet cables for host or hub/switch connections. (See

2.

The SmartNode comes with a built-in DHCP server to simplify conﬁguration. Therefore, to automatically

ﬁgure 1

.)

conﬁgure the PC for IP connectivity to the SmartNode, conﬁgure the laptop PC for DHCP. The SmartNode will provide the PC with an IP address.

3.

Check the connection to the SmartNode by executing the

ping

command from the PC command window

as follows:

ping 192.168.1.1

3.0 Conﬁguring the desired IP address

3.1 Factory-default IP settings

The factory default conﬁguration for the Ethernet interface IP addresses and netmasks are listed in Both Ethernet interfaces are activated upon power-up. LAN interface

ETH 0/1 (LAN)

provides a default DHCP server. The WAN interface uses DHCP client to get the IP address and netmask automatically from the service provider.

table 1

.

Table 1.

Item

WAN interface Ethernet 0 (ETH 0/0) LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0 DHCP server address range (LAN) 192.168.1.10-192.168.1.19 255.255.255.0

If these addresses match with those of your network, go to section

network”

on page 4. Otherwise, continue with the following sections to change the addresses and

network masks.

SmartNode 4634 & 4638 Quick Start Guide

Factory default IP address and network mask conﬁguration

IP Addresss Network Mask

DHCP DHCP

4.0 “Connecting the SmartNode to the

3

3.2 Login

1.

To access the SmartNode, start the Telnet application on your PC. Type the default IP address into the address ﬁeld: Type the factory default login:

192.168.1.1

. Accessing your SmartNode via a Telnet session displays the login screen.

administrator

and leave the password empty. Press the

password prompt.

Enter

key after the

login: password:<Enter>

192.168.1.1>

2.

After you log in, your SmartNode will be running in operator execution mode (indicated by > character in the command line prompt). To enter conﬁguration mode, use the commands

192.168.1.1>

192.168.1.1#

192.168.1.1(cfg)#

administrator

enable configure

enable

and

3.3 Changing the WAN IP address

1.

To modify IP conﬁguration settings, you must enter

192.168.1.1(cfg)#

192.168.1.1(ctx-ip)[router]#

2.

Now you can set your IP address and network mask for the interface

context ip router

network 172.16.1.0/24 is assumed. The IP address in example is set to

context IP

mode. Enter the following command:

ETH 0/0(WAN)

172.16.1.99

. In this example a

. (You should set it

to the IP address that the network provider has given you.)

Note

The examples in this guide use a private IP network with the network address

172.16.1.0/24

conﬁgure

.

192.168.1.1(ctx-ip)[router]#

192.168.1.1(if-ip)[eth0]# 2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0. 2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.99(if-ip)[eth0]#

3.

Copy this modiﬁed conﬁguration to your new start-up conﬁguration. This will store your changes in non-

interface eth0

ipaddress 172.16.1.99 255.255.255.0

volatile memory. On the next start-up the system will initialize itself using the modiﬁed conﬁguration.

172.16.1.99 (if-ip)[eth0]#

copy running-config startup-config

The SmartNode can now be connected to your network.

4.0 Connecting the SmartNode to the network

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, ﬂammability, and mechanical serviceability.

CAUTION

4

SmartNode 4634 & 4638 Quick Start Guide

In general, the SmartNode will connect to the network via the to offer routing services to the PC hosts on

LAN (ETH 0/1)

WAN (ETH 0/0)

port. This enables the SmartNode

port. The SmartNode 4630 Series provides an autoMDX feature for both Ethernet ports, so you can use a straight-through or cross-over cable to connect to a host or a switch (see

ﬁgure 2

Network

).

Straight-through wired

or crossover cable

WAN (ETH 0/0)

LAN

LAN (ETH 0/1)

Figure 2.

1.

You can check the connection with the ping command from the SmartNode to another host on the

Connecting the SmartNode to the network

local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Note

If the WAN address is the default gateway. (For information on conﬁguring the default gateway, refer to section “Set IP addresses” in Appendix C, “Command Summary” of the

uration Guide

not

set to DHCP, to ping a device outside your local LAN you must ﬁrst conﬁgure

SmartNode Series SmartWare Software Conﬁg-

.)

5.0 Loading the conﬁguration (optional)

Patton provides a collection of conﬁguration templates on the CD-ROM shipped with your SmartNode device— and also on the support page at application that you can use it to speed up conﬁguring the SmartNode. Simply download the conﬁguration note that matches your application to your PC. Adapt the conﬁguration as described in the conﬁguration note to your network (remember to modify the IP address) and copy the modiﬁed conﬁguration to a TFTP server. The SmartNode can now load its conﬁguration from this server.

www.patton.com/voip

—one of which may be similar enough to your

SmartNode 4634 & 4638 Quick Start Guide

5

Note

Patton regularly adds new conﬁguration templates to the collection at you do not see your application on the CD-ROM, it may have been added to the website.

Note

If your application is unique and not covered by any of Patton’s conﬁguration templates, you can manually conﬁgure the SmartNode instead of loading a conﬁguration ﬁle template. In that case, refer to the

SmartNode Series SmartWare Software Conﬁguration Guide

Node device.

www.patton.com/voip

for information on conﬁguring the Smart-

, so if

In this example we assume an TFTP server resides on the host with the IP address 172.16.1.11 and the conﬁguration ﬁle named

SN.cfg

resides in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#

config

Download...100%

172.16.1.99(if-ip)[eth0]#

copy tftp://172.16.1.11/SN.cfg startup-

After you reboot the SmartNode the new startup conﬁguration will become active.

When you issue the reload command, the SmartNode will ask if you want to copy the running conﬁguration to the startup conﬁguration. Since you just downloaded a conﬁguration ﬁle to the startup conﬁguration you must answer this question with NO.

IMPORTANT

172.16.1.99(if-ip)[eth0]# Running configuration has been changed. Do you want to copy the 'running-config' to the 'startup-config'? Press 'yes' to store, 'no' to drop changes : Press 'yes' to restart, 'no' to cancel : The system is going down

Otherwise, the downloaded conﬁguration will be overwritten and lost!

reload

no

yes

6.0 Additional Information

Refer to the located on the CD-ROM shipped with your SmartNode device and available online at

manuals.

•

Installing, conﬁguring, operating, and troubleshooting.

•

Warranty, trademark & compliance

SmartNode Series SmartWare Software Conﬁguration Guide

For detailed information about:

and the

SmartNode Getting Started Guide

www.patton.com/

The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.

A.0 Customer and Technical Support

Toll-Free VoIP support: call Online support: www E-mail support:

6

support@patton.com

sip:support@patton.com

.patton.com

—answered within 1 business day

with a VoIP SIP client

SmartNode 4634 & 4638 Quick Start Guide

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to 2200 UTC/GMT)

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

•

UTC/GMT)

Fax:

+1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

Safety Compliance:

• UL60950-1/CSA C22.2 No. 60950-1

• IEC/EN 60950-1

• AS/NZS 60950-1

PSTN Regulatory Compliance:

• TBR3

• AS/ACIF S031

B.2 Radio and TV interference

The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television reception. The SmartNode router have been tested and found to comply with the limits for a Class A computing device in accordance with speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).

SmartNode 4634 & 4638 Quick Start Guide

7

B.3 ISDN compliance

This device is approved for connection to the public ISDN telecommunication network.

When this device is used in North America, it shall be connected to a Network Termination Device and not connected directly to an outside POTS line.

CAUTION

B.4 CE Declaration of Conformity

Product Description: SmartNode 4630 Series

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of their conformity.

The safety advice in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certiﬁcations/.

B.5 Authorized European Representative

D R M Green European Compliance Services Limited. Avalon House, Marcham Road Abingdon, Oxon OX14 1UD, UK

B.6 Zulassung

Zugelassen fur die Anschaltung an das öffentliche ISDN Telekommunikationnetz an BRI/S0-ISDN Schnittstellen.

8 SmartNode 4634 & 4638 Quick Start Guide

Copyright statement

liability for errors that may appear in this document.

Trademarks statement

The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu- ment are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the Models SN4630 Series Getting Started Guide located on the CD-ROM that came with your VoIP Gateway Router or available online at www.patton.com.

In accordance with the requirements of council directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling.

SmartNode 4634 & 4638 Quick Start Guide 9

Notes

____________________________________________________________________

10 SmartNode 4634 & 4638 Quick Start Guide

Notes

____________________________________________________________________

Notes

____________________________________________________________________

12 SmartNode 4634 & 4638 Quick Start Guide