Patton electronics CopperLink Ethernet Extenders 2158A, CopperLink 2168A User Manual

USER MANUAL

CopperLink™ Ethernet Extenders Models 2168A and 2158A

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment.

Part# 07M2168A-UM Rev . C

Revised 4/20/1 0

An ISO-9001Certified

Company

SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007

CONTENTS

1.0 Warranty Information ................................................................. 4

1.1 Compliance ................................................................................... 4

EMC Compliance:.................... ...... ...... ..... .................................... 4

Safety Compliance:................. ..................................................... 4

PSTN Compliance:....................................................................... 4

1.2 Radio and TV Interference (FCC Part 15).................................... 5

1.3 CE Declaration of Conformity....................................................... 5

1.4 Authorized European Representative........................................... 5

1.5 Service.......................................................................................... 5

1.6 Safety When Working With Electricity .......................................... 6

2.0 General Information.................................................................... 7

2.1 Features........................................................................................ 7

2.2 Description.................................................................................... 8

3.0 Installation................................................................................... 9

3.1 Unit Installation............................................................................. 9

3.2 Grounding the CopperLink Ethernet Extender............................ 10

3.3 Connecting the Twisted-Pair Line Interface................................ 10

Using a Ferrite Clamp to Connect the Line In terface ................. 12

Connecting the ferrite clamp to the RJ-45 port. ............ ...... .12

Connecting the ferrite clamp to the termin al block . .............13

3.4 Connecting the 10/100Base-T Ethernet Interface ...................... 14

3.5 Connecting Power ......................... ............................................. 15

4.0 Configuration ............................................................................ 16

4.1 Configuring the hardware DIP switc hes...................................... 16

4.2 Configuring DIP Switch SW........................................................ 17

Switches SW-2 and SW-4: Data Rate............ ..... ....................... 17

Switches SW-1 and SW-5 through SW-8: Reserved.................. 17

5.0 Operation................................................................................... 18

5.1 Power Up.................................................................................... 18

5.2 Front Panel LED Status Monitors............................................... 18

A

Specifications ........................................................................... 20

A.1 LAN Connection ......................................................................... 20

A.2 Transmission Line ....................................................................... 20

A.3 CopperLink Line Rate ................................................................. 20

A.4 CopperLink Distance .................................................................. 20

A.5 CopperLink Surge Suppressor ................................................... 20

A.6 LED Status Indicators ................................................................. 20

A.7 Power Supply .............................................................................. 21

A.8 Temperature Range .................................................................... 21

A.9 Humidity ...................................................................................... 21

A.10 Dimensions ................................................................................. 21

2

B

Model 2168A and 2158A Series Factory

Replacement Parts and Accessories...................................... 22

C

CopperLink Series Interface Pin Assignment ........................ 24

C.1 10/100Base-T Interface .............................................................. 24

RJ-45.......................................................................................... 24

C.2 CopperLink Interface .................................................................. 24

RJ-45.......................................................................................... 24

Terminal Block............................................................................ 24

D

Distance Chart, Based on 24 AWG (0.5 MM).......................... 25

3

1.0 WARRANTY INFORMATION

Patton Electronics warrants all CopperLink Ethernet Extender components to be f ree from defects, an d will—at our option—repair or repla c e the product should it fail within one year from the first date of the ship

-

ment. This warranty is lim ited to defect s in workman ship or mate rials, and do es

not cover customer damage, abuse or unauthorized modification. If this product fails o r do es not p erforms as w arrante d, your sole re cours e shal l be repair or replacem ent as des cr ibed above. Under no conditio n shal l Patton Electronics be liable for any damages incurred by the use of this product. These da mages incl ude, but are no t limited to, the foll owing: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product. Patton Electronics spe

cifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed an acceptance of these terms by the user.

Note Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 COMPLIANCE

EMC Compliance:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

Safety Compliance:

• IEC/EN 60950-1

• AS/NZS 60950-1

PSTN Compliance:

Note This device is not intended nor approved for connection to the

PSTN.

4

1.2 RADIO AND TV INTERFERENCE (FCC PART 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manu

facturer's instructions—may cause interference to radio and television reception. This eq uip ment has been tested and found to com pl y wi th the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules , which are desig ned to provide reasonable protection from such interference in a commercial installa

tion. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by disconnecting the cables, try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, reorienting the re ceiv ing an tenna, and/or plu gging the rec eiving equipm ent into a different AC outlet (such that the computing equipment and receiver are on different branches).

1.3 CE DECLARATION OF CONFORMITY

We certify that the apparatus described above conforms to the requirements of Council Directive 2004/108/EC on the approximation of the laws of the member states relating to electromagnetic compatibility; and Council Directive 2006/95/EC on the approximation of the laws of the member states relating to electrical equipment designed for use within certain voltage limits.

1.4 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green European Compliance Services Limited. Avalon House, Marcham Road Abingdon, Oxon OX14 1UD, UK

1.5 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid and insured to Patto n Elec tro nic s. All retu rns must hav e a R et urn Mate ri als Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Services at:

•Tel: +1 (301) 975-1007

•Email: support@patton.com

• URL: http://www.patton.com

-

5

Note Packages received without an RMA number will not be

accepted.

1.6 SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel.

• The external power adapter shall be a listed Limited Power Source. Ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground. The mains

WARNING

outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker.

• Do not work on the system or connect or disconnect cables during periods of lightning activity.

WARNING

In accordance with the requirements of council directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy cling.

This device is NOT intended nor approved for connection to the PSTN. It is intended only for connection to customer premise equipment.

The Interconnecting cables shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical service ability

-

6

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007.

2.1 FEATURES

• Easy to install CopperLink Ethernet Extenders (no configuration required)

• Auto MDIX Ethernet

• Auto-sensing full or half-duplex Ethernet

• Auto-sensing 10/100Base-TX

• Extends network connections up to 6,000 ft (1.83 km) over 2-wire 24AWG unconditioned lines

• Switch selectable line rates up to 16.67 Mbps

• 7 total symmetric or asymmetric settings via DIP switch (2168A and 2168A/TB45 models only)

• Transparent operation

• LED indicators for Power, Ethernet Link & Activity , CopperLink link & Quality of Line (QOL)

• Surge suppression up to 200 A (8/20 ms)

• Made in the USA

7

2.2 DESCRIPTION

The Patton Electronics CopperLink/L and CopperLink/R Ethernet Extenders provide high-speed LAN connections between peered Ether

net LANs, remote PCs, or any other network enabl ed 10/ 100 Bas e-T device.

Operating in pairs, a CopperLink/L (local) lo cated at one end of the LAN extension and a CopperLink/R (remote) at the other end, these units can automatically forward LAN broadcasts, multicast s , and frames ac ross a 2wire voice-grade twisted-pair link. The data is passed transparently (unmodified) through the CopperLink Ethernet Extenders. The CopperLink Ethernet Extenders automatically add and delete MAC addresses, only passing packet s across the Coppe rLink link that are meant for the remote peered LAN.

Figure 1. Typical application

The CopperLink/Lunit and CopperLink/R unit work together to create a transparent extension between two peered Ethernet LANs.

Figure 1

shows a typical point-to-point application.

8

3.0 INSTALLATION

ir

Because the CopperLink Ethernet Extender requires no configuration, it can be installed quickly.

Note If asymmetric transmission or line rates other than 12.5 Mbps

are required , refer to section 4.0, “Configuration” on page 16.

3.1 UNIT INSTALLATION

Do the following:

1. Make a ground connect ion for the unit (r efer to section 3.2, “Ground-

ing the CopperLink Ethernet Extender” on page 10).

2. Connect the line interface between the units (refer to section 3.3,

“Connecting the Twisted-Pair Line Interface” on page 10)

Note See Figure 2 for the unit’s rear panel arrangements.

3. Connect the Ethernet inte rface (refer to sectio n 3.4, “Connecti ng the

10/100Base-T E thernet Interface” on page 14).

4. Connect the power p lug (refer to se ction 3.5, “Co nnecting Powe r” on

page 15).

CopperLink 2168A/TB45

Power

CopperLink 2168A CopperLink 2158A

Ground

Power

connector

stud

CopperLink twisted-pa

CopperLink twisted-pair

RJ-45 interface

connector

Ethernet

port

terminal block

interface

Ground

stud

Figure 2. CopperLink Ethernet Extender rear panel

Ethernet

port

CopperLink twisted-pair

RJ-45 interface

9

3.2 GROUNDING THE COPPERLINK ETHERNET EXTENDER

Before installing the CopperLink Ethernet Extender, it is important to establish a good grounding connection first.

1. Assemble a ground wire using #10 AWG wire with green-and-yel-

low-colored insulation and two ring terminals. Make the wire long enough to reach one of the following earth ground sources:

— The building ground rod (generally located at the site’s main

service entrance) — A spri nkler system pipe — A metal cold-water pipe — Building structural steel

2. Install the grounding w ire bet we en the grou nd ing stud (see Figure 2 on page 9) and the grounding source.

3.3 CONNECTING THE TWISTED-PAIR LINE INTERFACE

The CopperLink Ethernet Extender supports communication between two peer Ethernet LAN sites over a distance of up to 6,000 ft (1.83 km) over 24 AWG (0.5 mm) twisted-pair wire.

Note Actual distance and link performance may vary depending on

the environment and type/gauge of wire used.

Follow the steps below to connect the CopperLink Ethernet Extenders interfaces.

Note The CopperLink units work in pairs. One of the CopperLink units

must be an L (local), and the other unit must be an R (remote). It does not matter which end is the L and which is the R. The link is always initiated by the R. As long as the L is powered on, the R can establish a link by being powered on or by having its power reset.

1. To function properly, the two CopperLink Ethernet Extenders must be connected together using twisted-pair, unconditioned, dry, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable.

2. The CopperLink Ethernet Extenders are equipped with an interface jack that can be used on the CopperLink interface, an RJ-45 (2168A or 2158A), or a terminal block (2168A/TB45, which also has the RJ-45 interface). These CopperLink interfaces are a two-wire interface. Observe the signal/pin relationships on the C opperLink Ethernet Extender's CopperLink interface jacks.

10

The RJ-45 connector on the CopperLink Ethernet Extender's twisted

) ) )

pair interface is polarity insensitive and is wired for a two-wire inter face. The signal/pin relationship is shown in Figure 3.

1 (no connection

-

1 2

2 (no connection 3 (no connection

3 4 5 6 7 8

4 (2-Wire RING) 5 (2-Wire TIP) 6 (no connection 7 (no connection 8 (no connection

Figure 3. CopperLink Ethernet Extender (RJ-45) twisted pair line interface.

The terminal block connector on the CopperLink Ethernet Extender's twisted pair interface is polarity insensitive and is wired for a two-wire interface. The signal/pin relationships are shown in Figure 4.

Figure 4. CopperLink2168A/TB45 Ethernet Extender twisted pair line interface.

11

RING TIP

Using a Ferrite Clamp to Connect the Line Interface

• The ferrite clamp that is shipped with the unit must be used as detailed in the following instructions in order to meet EMC requirements.

WARNING

Connecting the ferrite clamp to the RJ-45 port.

To connect the ferrite clamp to the RJ-45 port:

1. Place the RJ-45 cable inside the ferrite clamp, leaving about 1-2 inches of cable between the unit and clamp.

2. Wrap the cable tightly around the clamp two times and secure the wire firmly in the clamp channel.

3. Close the clamp an d connect the cable to the line port on the unit

Figure 2 on page 9).

(See

Model 2168A Model 2158A

Note: Be sure to leave 1-2 inches of cable between the unit and the ferrite clamp.

CopperLink twisted-pair

RJ-45 interface

Ferrite clamp

Figure 5. Connecting the ferrite clamp for 2168A/2158A models

12

Connecting the ferrite clamp to the terminal block.

To connect the ferrite clamp to the terminal block:

1. Place the cable inside the ferrite clamp, leaving about 1-2 inches of cable between the unit and clamp.

2. Wrap the cable tightly around the clamp two times and secure the wire firmly in the clamp channel.

3. Close the clamp an d connect the cable to the line port on the unit

Figure 2 on page 9).

(See

Model 2168A/TB45

Note: Be sure to leave 1-2 inches of cable between the unit and the ferrite clamp.

CopperLink twisted-pair

RJ-45 interface

CopperLink twisted-pair

terminal block

interface

Figure 6. Connecting the ferrite clamp for 2168A/TB45 models

Ferrite clamp

13

3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE

)

The RJ-45 port labeled Ethernet is the Auto-MDIX10/100Base-T interface. This port is designed to connect directly to a 10/100Base-T network. Figure 7 shows the signal/pin relationships on this interface. You may connect this port to a hub or PC using a straight through or crossover cable that is up to 328 ft long.

1 TX+/RX+ (data output from CopperLink

1 2 3 4 5 6 7 8

Figure 7. CopperLink Ethernet Extender 10/100Base-T RJ-45 Connector Pinout.

2 TX-/RX- (data output from Copperlink) 3 RX+/TX+ (data input to CopperLink) 4 (no connection) 5 (no connection) 6 RX-/TX-(data input to CopperLink) 7 (no connection) 8 (no connection)

14

3.5 CONNECTING POWER

• Do not connect power to the DC Mains at this time.

• There are no user-serviceable parts in the power supply sec tion of the CopperLink Ethernet Extender. Contact Patton Elec

WARNING

tronics Technical support at (301)975-1007, via our web site at http://www.patton.com, or by e-mail at support@pat

-

ton.com, for more information.

An external AC or DC power supply is available separately. This connection is made via the barrel jack on the rear panel of the CopperLink Ethernet Extender. No configuration is necessary for the power supply (See Appendix B for domestic and international power supply and cord options).

DC power (supplied via the power supply jack to the CopperLink Ethernet Extender) must meet the following requirements; DC power supplied must be regulated +5VDC ±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has a 2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.

The CopperLink Ethernet Extender does not have a power switch, so it powers up as soon as it is plugged in.

-

15

4.0 CONFIGURATION

The CopperLink Models 2168A and 2168A/TB45 have an eight-position DIP switch for configuri ng the unit for a wide variety of applications. This section describes switch locations and explains the different configurations. The Model 2158A does not include dip switches.

4.1 CONFIGURING THE HARDWARE DIP SWITCHES

Using a sm all fl at-tip screwd river, remove the prote ctive cov er loc ated on the underside of the CopperLink Ethernet Extender (see

Figure 8).

C

o

p

p e r

L i n

k

CopperLink™ Ethernet Extender

Figure 8. Removing protective cover

Figure 9 on page 16 shows the orientation of the DIP swit ch es in the On and Off positions.

SW

Figure 9. Models 2168A and 2168A/TB45 DIP switch orientation

16

4.2 CONFIGURING DIP SWITCH SW

DIP switch SW is where you configure the CopperLink line rate, and if the rate is symmetric or asymmetric.

Switches SW-2 and SW-4: Data Rate

Use switches SW-2 and SW-4 to configure the CopperLink line rates.

Table 1: Symmetric CopperLink Line Rates Selection Chart

SW-2 SW-3 SW-4 Symmetric Line Rate

ON ON ON 6.25 Mbps ON ON OFF 9.38 Mbps ON OFF OFF

12.5 Mbps (Factory Default)

*

ON OFF ON 16.67 Mbps

*. Model 2158A only has one symmetric line

rate setting, which is 12.5 Mbps.

Note Table 2 only applies to Models 2168A and 2168A/TB45.

Table 2: Model 2168A and 2168A/TB45 Asymmetric CopperLink Line Rates Selection Chart

SW-2 SW-3 SW-4

Asymmetric Line Rates DS/US

*

OFF OFF ON 4.17 Mbps/1.56 Mbps OFF ON ON 9.38 Mbps/ 1.56 Mbps OFF ON OFF 16 .67 Mb ps/2.34 Mbps

*. DS = downstream from L unit to R unit

US = upstream from R unit to L unit

Switches SW-1 and SW-5 through SW-8: Reserved

Table 3: Reserved for future use

SW-1 SW-5 SW-6 SW-7 SW-8 Reserved for future use

OFF OFF OFF OFF OFF Reserved

(Factory Default)

17

5.0 OPERATION

t D

Once the CopperLink Ethernet Extenders are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors.

5.1 POWER UP

Before applying power to the CopperLink Ethernet Extender, please review

section 3.5, “Conn ecting Power” on page 15 to ve rify th at t he unit

is connected to the appropriate power source.

There are no user-serviceable parts in the CopperLink Ethernet Extender. Fuse replacement should only be performed by quali

-

fied service personnel. Contact Patton Electronics Technical sup-

WARNING

port at (301) 975-1007 for more information.

5.2 FRONT PANEL LED STATUS MONITORS

The CopperLink Ethernet Exte nder featu res se ven front p anel L EDs (five on the rack card) that monitor power, the Ethernet signals, and the Cop perLink connection. Figure 10 shows the front panel LEDs. Table 4 on page 19 describes the LED functions for the model.

-

r

e

d

n

te

x

t E

e

n

r

e

th

E

™

k

in

rL

e

p

o

C

Fdx

100M LE

CopperLink

Ethernet Fdx LED

Ethernet

Collision LED

Power

LED

Ethernet

Link LED

CopperLink

QOL LED

CopperLink

Link LED

Figure 10. CopperLink Ethernet Extender unit front panel

Etherne

18

Tab le 4: Front panel LED description for the 2168A

LED Description

Power On (green) when power is applied to the unit. Off

when no power is applied to the unit.

CopperLink Link

On (green) when the end-to-end CopperLink link between the units is established. Off when the link has not been established or when the link fails

CopperLink QOL

Flashes yellow at different rates to indicate the amount of error correction taking place on data pass ing over the CopperLink link. This is a normal operating condition an d all data is passing corre ctly over the link even if the link is solidly yellow. However, if the

LED is solid yellow and the CopperLink Link LED is Off, then there is too much noise on the line for an

active link.

Ethernet - Link On (green) when the 10/ 100Base-T Ethernet link has

been established. Off when the 10/100Base-T Ether net link has not been established or when the link fails. Flashes when there is Ethernet activity.

Ethernet - COL (Collision)

Ethernet - FDX (Duplex)

Flashes yellow to indicate Ethernet collisions are occurring.

On (yellow) when in full-duplex Ethernet mode. Off when when operating in half-duplex Ethernet mode.

Ethernet - 100M On (yellow) when the link has not been established

or when operating in 100-Mbps Ethernet mode. Off when operating in 10-Mbps Ethernet mode.

-

19

APPENDIX A

S PECIFICATIONS

A.1 LAN CONNECTION

• Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet

• CopperLink Connection: — 2168A/TB45: RJ-45 and Terminal Block

— 2168A/2158A: RJ-45 only

A.2 TRANSMISSION LINE

Two-wire unconditioned twisted pair.

A.3 COPPERLINK LINE RATE

16.67 Mbps (Model 2168A and Model 2168A/TB45) and 12.55 Mbps

(Model 21 58A) symmetric upstream/downstream. Additional symmetric and asymmetric rates are available via DIP switch settings:

• Model 2158A - Symmetric Line Rate: 12.5 Mbps

• Model 2168A and Model 2168A/TB45 - Symmetric Line Rates:

6.25 Mbps, 9.38 Mbps, 12.5 Mbps, 16.67 Mbps

• Model 2168A and Model 2168A/TB45 - Asymmetric Line Rates:

4.17 Mbps/1.56 Mbps, 9.38 Mbps/1.56 Mbps, 16.67 Mbps/2.34 Mbps

A.4 COPPERLINK DISTANCE

6,000 ft (1.83 km) at 1.56 Mbps upstream/4.17 Mbps downstream

Note Distances depend on selected line rate.

A.5 COPPERLINK SURGE SUPPRESSOR

Transient peak surge maximum current: 200A (8/20 ms).

A.6 LED STATUS INDICATORS

• Power (Green)

• CopperLink: Link (Green) & QOL (Yellow)

• Ethernet: Link (Green), Collision (Yellow), Duplex (Yellow), 10/100M

(Yellow)

20

A.7 POWER SUPPLY

Input power: 5 VDC, 1A Power consumption: 560 mA at 5 VDC (typical) External AC and DC options:

• AC: 120 VAC, 220 VAC, and UI (120–240 VAC)

• DC: 12 VDC, 24 VDC and 48 VDC

Internal 36-72VDC (nominal 48V) Terminal Block Plug (1x3, 3.81mm, with screws) Pin Header Socket Connector

A.8 TEMPERATURE RANGE

32–122°F (0–50°C)

A.9 HUMIDITY

Up to 90% non-condensing.

A.10 DIMENSIONS

1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm)

21

APPENDIX B

MODEL 2168A AND 2158A SERIES FACTORY

REPLACEMENT PARTS AND ACCESSORIES

Patton Model # Description

Base Models

2158A/E-2PK CopperLink 12.5 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit); No power supply

2158A/EUI-2PK CopperLink 12.5 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit); 100-240VAC

2158A/L/E 12.5 Mbps CopperLink Ethernet Extender (Local);

RJ45 line; No Power Supply

2158A/L/EUI 12.5 Mbps CopperLink Ethernet Extender (Local);

RJ45 line; 100-240VAC

2158A/R/E 12.5 Mbps CopperLink Ethernet Extender (Remote);

RJ45 line; No Power Supply

2158A/R/EUI 12.5 Mbps CopperLink Ethernet Extender (Remote);

RJ45 line; No Power Supply

2168A/E-2PK CopperLink Multi Rate 16 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit); No power supply

2168A/EUI-2PK CopperLink Multi Rate 16 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit);RJ45 Connectors only; 100-240VAC

2168A/L/E 16 Mbps Ethernet Extender Kit (Local); RJ45 line;

No Power Supply

2168A/L/EUI 16 Mbps Ethernet Extender Kit (Local); RJ45 line;

100-240VAC

2168A/L/TB45/E 16 Mbps Ethernet Extender Kit (Local);

Terminal Block and RJ45 line; No Power Supply

2168A/L/TB45/EUI 16 Mbps Ethernet Extender Kit (Local);

Terminal Block and RJ45 line; 100-240VAC

2168A/R/E 16 Mbps Ethernet Extender Kit (Remote); RJ45 line;

No Power Supply

2168A/R/EUI 16 Mbps Ethernet Extender Kit (Remote); RJ45 line;

100-240VAC

2168A/R/TB45/E 16 Mbps Ethernet Extender Kit (Remote);

Terminal Block and RJ45 line; No Power Supply

2168A/R/TB45/EUI 16 Mbps Ethernet Extender Kit (Remote);

Terminal Block and RJ45 line; 100-240VAC

2168A/TB45/E-2PK CopperLink Multi Rate 16 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit); Terminal Block Line side; No power supply

2168A/TB45/EUI-2PK CopperLink Multi Rate 16 Mbps Ethernet Extender Kit

(1 Local Unit and 1 Remote Unit); Terminal Block Line side; 100-240VAC

07M2168A-UM

User Manual

22

Patton Model # Description

Power Supplies

08055DCUI 08055-120-5-1

12V-PSM 12 VDC Input Adapter 24V-PSM 24 VDC Input Adapter 48V-PSM 48 VDC Input Adapter

Power Cords

0805US American Power Cord 0805EUR European Power Cord CEE 7 0805UK United Kingdom Power Cord 0805AUS Aus tralian Power Cord 0805DEN Denmark Power Cord 0805FR France/Belgium Powe r Cord 0805IN India Power Cord 0805IS Israel Power Cord 0805JAP Japan Power Cord 0805SW Switzerland Power Cord

(Only required with optional UI power supply (08055DCUI)

100-240V AC (+5V reg. DC/2A) Universal Input Adapter. 120 V A C (+5V reg. DC/1A) Input Adapter

23

APPENDIX C

COPPERLINK SERIES INTERFACE PIN ASSIGNMENT

C.1 10/100BASE-T INTERFACE

RJ-45

• Pin 1: TX+/RX+

• Pin 2: TX-/RX-

• Pin 3: RX+/TX+

• Pin 6: RX -/TX-

• Pins 4, 5, 7, 8: no connection

C.2 COPPERLINK INTER FACE

RJ-45

• Pin 4: RING

• Pin 5: TIP

• Pins 1, 2, 3, 6, 7, 8: no connection

Terminal Block

See Figure 4 on pag e 11.

24

APPENDIX D

DISTANCE CHART, BASED ON 24 AWG (0.5 MM)

Symm Line Rate Distance in feet (km)

6.25 Mbps 4,500 (1.37)

9.38 Mbps 4,150 (1.26)

*

12.5 Mbps

4,000 (1.22)

16.67 Mbps 3,300 (1.00)

*. This is the only option available for Model

2158A.

Asymm Line Rate (DS/US) Distance in feet (km)

4.17 Mbps/1.56 Mbps (Mode 0) 6,000 (1.83)

9.38 Mbps/ 1.56 Mbps 5,500 (1.68)

16.67 Mbps/2.34 Mbps 5,000 (1.52)

Note

DS = downstream from L unit to R unit US = upstream from R unit to L unit

25

NOTES

_________________________________________________________

26

NOTES

_________________________________________________________

27

NOTES

_________________________________________________________

Patton Electronics Company

28

Patton electronics CopperLink Ethernet Extenders 2158A, CopperLink 2168A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual