Patton electronics COPPERLINK 2150 User Manual

USER
MANUAL

MODEL 2150

CopperLINK™
Ethernet Extender

This is a Class A device and is not intended for
use in a residential environment.

Part# 07M2150-U M
Rev . B
Revised 8/31/1 0

An ISO-9001Certified

Company

SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]

CONTENTS

1.0 Warranty Information ................................................................. 4

1.1 Regulatory Information ................................................................. 4

EMC Directive:......................... ...... ............................ ...... ..... ...... .. 4

Low-Voltage Direcive (Safety):..................................................... 4

PSTN:.................................................. ......................................... 4

1.2 Radio and TV Interference (FCC Part 15).................................... 4

1.3 CE Declaration of Conformity....................................................... 5

1.4 Authorized European Representative........................................... 5

1.5 Service.......................................................................................... 5

1.6 Safety When Working With Electricity .......................................... 6

2.0 General Information.................................................................... 8

2.1 Features........................................................................................ 8

2.2 Description.................................................................................... 8

3.0 Installation................................................................................... 9

3.1 Connecting the Twisted-Pair Line Interface................................ 10

3.2 Connecting the 10/100Base-T Ethernet Interface ...................... 11

3.3 Connecting Power ......................... ............................................. 12

4.0 Configuration ............................................................................ 12

4.1 Configuring the hardware DIP switc hes...................................... 12

4.2 Configuring DIP Switch S1 ......................................................... 14

5.0 Operation................................................................................... 14

5.1 Power Up.................................................................................... 14

5.2 Front Panel LED Status Monitors............................................... 15

A

Specifications ........................................................................... 16

A.1 LAN Connection ......................................................................... 16

A.2 Transmission Line ....................................................................... 16

A.3 CopperLINK Distance ................................................................. 16

A.4 LED Status Indicators ................................................................. 16

A.5 Power Supply .............................................................................. 16

A.6 Temperature Range .................................................................... 16

A.7 Humidity ...................................................................................... 16

A.8 Dimensions ................................................................................. 16

B

Model 2150 Series Factory

Replacement Parts and Accessories...................................... 17

C

Model 2150 Series Interface Pin Assignment ........................ 18

C.1 10/100Base-T Interface .............................................................. 18

RJ-45.......................................................................................... 18

C.2 CopperLINK Interface ................................................................ 18

RJ-45.......................................................................................... 18

2

D

Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19

3

1.0 WARRANTY INFORMATION

Patton Electronics warrant s all Mo del 2150 co mpone nts to be free from
defects, and will—at our option—repair or replace the product should it
fail within one year from the first date of the shipment.

This warranty is lim ited to defect s in workman ship or mate rials, and do es
not cover customer damage, abuse or unauthorized modification. If this
product fails o r do es not p erforms as w arrante d, your sole re cours e shal l
be repair or replacem ent as des cr ibed above. Under no condi tio n shal l
Patton Electronics be liable for any damages incurred by the use of this
product. These da mages incl ude, but are no t limited to, the foll owing: lost
profits, lost savings and incidental or consequential damages arising
from the use of or inability to use this product. Patton Electronics spe

­cifically disclaims all other warranties, expressed or implied, and the
installation or use of this product shall be deemed an acceptance of
these terms by the user.

Note Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 REGULATORY INFORMATION

EMC Directive:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

• A-tick

Low-Voltage Direcive (Safety):

• IEC/EN60950-1, 2nd Edition

• AS/NZS 60950-1, A-tick

PSTN:

• This device is not intended nor approved for connection to the PSTN

1.2 RADIO AND TV INTERFERENCE (FCC PART 15)

This device generates and uses radio frequency energy, and if not
installed and use d proper ly- that is, in s trict ac corda nce with the man ufac
turer’s instructions-may cause interference to radio and television recep-

-

4

tion. The de vi ce h as b een tested and found t o co mply with the lim its for a
Class A com puting devi ce i n accord ance with s pecifi catio ns in Subp art B
of Part 15 of FCC rules, which are designed to provide reasonable pro

­tection from such interference in a commercial installation. However,
there is no gua ran tee that interference will not occur in a particular instal
lation. If the device does cause interference to radio or television recep­tion, which can be determined by disconnecting the unit, the user is
encouraged to try to corr ect the interf erence by on e or more of t he follow
ing measures : m ov ing the c omp uti ng equipment away from the receive r,
re-orienting the receiving antenna and/or plugging the receiving equip

­ment into a different AC outlet (such that the computing equipment and
receiver are on different branches).

1.3 CE DECLARATION OF CONFORMITY

Patton Electronic s, Inc de clares that th is dev ice i s in c ompli ance wi th the
essential requirements and other relevant provisions of Directive
2004/108/EC relating to electromagnetic compatibility and Directive
2006/95/EC relating to electrical equipment designed for use within cer

­tain voltage limits. The Declaration of Conformity may be obtained from
Patton Electronics, Inc at www.patton.com/certifications.

-

-

The safety advice in the documentation accompanying this device shall
be obeyed. The conformity to the above directive is indicated by CE
mark on the device.

1.4 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green
European Compliance Services Limited.
Avalon House, Marcham Road
Abingdon, Oxon OX14 1UD, UK

1.5 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patto n Elec tro nic s. All retu rns must hav e a R et urn Mate ri
als Authorization number on the outside of the shipping container. This
number may be obtained from Patton Electronics Technical Services at:

•Tel: [phone]

•Email: [e-mail]

-

• URL: http://www.patton.com

Note Packages received without an RMA number will not be

accepted.

5

1.6 SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. This
device can only be repaired by qualified service per
sonnel.

• Do not open the device when the power cord is con­nected. For systems without a power switch and without
an external power adapter, line voltages are present
within the device when the power cord is connected.

• For devices with an external power adapter, the power
adapter shall be a listed Limited Power Source. The
mains outlet that is utilized to power the device shall be
within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker in com
pliance with local regulatory requirements.

• For AC powered devices, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed.

-

-

WARNING

• For AC powered devices which have 3 conductor
power plugs (L1, L2 & GND or Hot, Neutral &
Safety/Protective Ground), the wall outlet (or socket)
must have an earth ground.

• For DC powered devices, ensure that the interconnect­ing cables are rated for proper voltage, current, antici­pated temperature, flammability, and mechanical
serviceability.

• WAN, LAN & PSTN ports (connections) may have haz­ardous voltages present regardless of whether the
device is powered ON or OFF. PSTN relates to inter

­faces such as telephone lines, FXS, FXO, DSL, xDSL,
T1, E1, ISDN, Voice, etc. These are known as “hazard

­ous network voltages” and to avoid electric shock use
caution when working near these ports. When discon

­necting cables for these ports, detach the far end con­nection first.

• Do not work on the device or connect or disconnect
cables during periods of lightning activity.

6