Patton electronics 570-R8, 570-R16, 580-R8, 580-R16 User Manual

USER
MANUAL

MODEL 570-R8/570-R16

580-R8/580-R16

100Base-T (CAT-5)
Surge Protectors

SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com

Part #07M570/580RC-A
Doc# 074101UA
Revised 2/13/97

CERTIFIED

An ISO-9001

Certified Company

2

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions or problems
arise during installation or use of this product, please do not hesitate to
contact Patton Electronics Customer Service at [phone].

2.1 FEATURES

• Optional 8 or 16 port surge protection

• Multi-level surge protection

• Operation at Speeds up to 100 Mbps

• Optional 2, 4, 6 or 8 wire versions

• EIA/TIA TSB-40A Category 5 Compliant

• N.E.X.T. better than -40 dB at 100 MHz

• Shunts surges directly to chassis ground

• Easy to install

• Made in the U.S. A.

2.2 DESCRIPTION

The Patton Model 570 and 580 Rack Mount Series Surge
Protectors provide effective surge protection for devices operating in

Category-5 Cabling Systems. The Model 570-Rx is specifically
designed for point-of-use installation; the Model 580-Rx is designed to
be installed at the building entrance. Both models use a multi-stage
Silicon Avalanche Diode circuit, and will continue functioning while
handling the appropriate IEC 801.5 surges applicable to their use (see
the tables in Appendix B). Both the 570-Rx and 580-Rx will
additionally protect against surges up to and exceeding 2kV/1kA in fail­safe mode.

Model’s 570-Rx and 580-Rx support a wide range of balanced
interfaces from RS-422 to 100Base-T4. Highlights include a low
insertion loss (less than 0.4dB at 100MHz) and minimal near end cross
talk (better than -40 dB at all frequencies up to 100 MHz). Grounding is
accomplished via a braided ground strap that provides a separate unit­rack connection. The customer is responsible for ensuring a proper
rack to earth ground connection. For proper grounding, the resistance
from the supplied ground lug to the rack frame ground should be less
than 2.5 milliohms. Contact Technical Support if further details are
needed for this measurement.

Warning:

This product will not provide complete protection should your

equipment or building be subject to a direct lightning hit.

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 570/580 Rack Mount
components to be free from defects, and will—at our option—repair or
replace the product should it fail within one year from the first date of
shipment. This warranty is limited to defects in workmanship or
materials, and does not cover customer damage, abuse or
unauthorized modification. If this product fails or does not perform as
warranted, your sole recourse shall be repair or replacement as
described above. Under no condition shall Patton Electronics be
liable for any damages incurred by the use of this product. These
damages include, but are not limited to, the following: lost profits, lost
savings and incidental or consequential damages arising from the use
of or inability to use this product. Patton Electronics specifically
disclaims all other warranties, expressed or implied, and the installation
or use of this product shall be deemed an acceptance of these terms by
the user.

1.1 SERVICE

All warranty and nonwarranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Service: [phone]; http://www.patton.com; or

[e-mail].

Note: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 570/580-Rx. Technical Service hours: 8AM to 5PM EST,

Monday through Friday.

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Technical
Support.

1

3.0 INSTALLATION

Model’s 570-Rx and 580-Rx surge protectors are easy to install
and are designed to operate transparently to your network. This
section describes connection procedures for both models.

3.1 PRODUCT APPLICATIONS

Both Model’s 570/580-Rx protect all eight pins on a modular RJ-45
Cat-5 interface, and work in environments with data rates up to 100
Mbps. The following descriptions will give you a general guideline for
installing the units in your Cat-5 environment.

3.1.1 Point-Of-Use Applications Model 570-Rx)

The Model 570-Rx is designed for 100MHz point-of-use
installations that use networking standards such as 100BaseT, RS-422
or 100VG-AnyLAN. Typical installations are shown in Figures 1 and 2,
below. For best results the Model 570-Rx should be connected as
close as possible to the communication port of the device to be
protected .

3.1.2 Barrier Applications (MODEL 580-Rx)

The Model 580-Rx is a more robust protector than the Model 570­Rx, and is designed for use as a barrier protector on LAN equipment in
campus networks. Applications include cable runs between buildings,
cable runs between floors on multi-story structures, and as a higher
capacity replacement for the Model 570-Rx.

The Model 580-Rx is also well suited for use in severe lightning areas,
heavy industrial environments, and situations where heavy machinery
is in the direct vicinity of sensitive LAN equipment and cabling. Figure
3 below shows a typical application for the Model 580-Rx. For best
results, the braided grounding strap(s) on the rack should be attached
to the grounded metal frame of the rack structure.

3.2 INSTALLATION PROCEDURES

In order to operate as designed, the Model 570-Rx and 580-Rx

must be connected correctly

to your Cat-5 network. Please read all the

instructions below and follow them carefully.

3.2.1 Connecting the Model 570-Rx or 580-Rx to an I/O Port

1. Turn off equipment power and unplug (disconnect) the existing
connection between the UTP cable and the equipment’s I/O port.

3

Figure 2. Model 570-Rx in a Typical 100Base-T Point of Use Application

4

Workstation

Workstation

Workstation

Model 570/580-RX

Scale

Conveyor

Time Clock

Controller

Workstation

Model 570’s or 580’s

Model 570’s
or 580’s

Model 570’s or 580’s

Local Hub

Model 570
or 580

Model 580-Rx

Ground Connection

To Other
Building or
Wall

Exterior Wall

Electrical Panel

Figure 3. Barrier Application for 580-Rx

Figure 1. Model 570-Rx in a Typical RS-422 Point of Use Application