Patton electronics 400 User Manual

USER
MANUAL

MODEL 400

Coax to Twisted Pair
Adapter (BALUN)

SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com

Part# 07M400-C
Doc# 019051UC
Revised 9/26/94

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 400 components to be free
from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and
does not cover customer damage, abuse or unauthorized modification.
If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or consequen­tial damages arising from the use of or inability to use this product.
Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.

1.1 SERVICE

All warranty and non-warranty repairs must be returned freight pre­paid and insured to Patton Electronics. All returns must have a Return
Materials Authorization number on the outside of the shipping container.
This number may be obtained from Patton Electronics Technical
Service at [phone].

Packages received without an RMA number

will not be accepted.

Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 400. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

1

2

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is warrant­ed for One Year parts and labor. If any questions or problems arise
during installation or use of this product, please do not hesitate to con­tact Patton Electronics Technical Support at [phone].

2.1 FEATURES

• Two different formats available for coax connection:

BNC male or female
BNC male or female on 6” coax pig tail

• Seven different formats available for twisted pair connection:

RJ-11 jack
RJ-45 jack
Terminal block
RJ-11 jack/terminal block
RJ-45 jack/terminal block
Twisted pair pig-tail with RJ-11 plug
Twisted pair pig-tail with RJ-45 plug

• Transparent to data and protocol

• No AC power or batteries required (passive)

• Full AC or DC isolation up to 500 volts between link and data

2.2 DESCRIPTION

Use twisted pair telephone line instead of coax cable for your IBM
3270 computer system: Most IBM 3270 computer systems are con­nected together using coax cables with twist-type BNC connectors.
These cables are fairly expensive to purchase and costly to install. On
the other hand, most buildings are already wired for telephone sys­tems, and it is quite easy to use this existing telephone wiring to con­nect computer equipment.

With a pair of Patton Electronics Model 400 baluns, any IBM 3270
Type A equipment can be interconnected over single-pair telephone
wire at distances up to 1200 feet! This can result in significant sav­ings!

RJ-11 SIGNAL RJ-45 SIGNAL

1----------------No Connection 1 --------------No Connection

2----------------Ground 2 --------------No Connection

3----------------TIP 3 --------------Ground

4----------------RING 4 --------------TIP

5----------------Ground 5 --------------RING

6----------------No Connection 6 --------------Ground

7 --------------No Connection
8 --------------No Connection

Note: If the distance from the Model 400 to the wall plate is

greater than 12 feet, Patton Electronics recommends that the
jumper cables be of 22, 24 or 26 gauge twisted pair wire, rather
than flat silver cable.

3. Once all wiring is determined to be straight through,
connect the Model 400s to the controller/computer
and the remote peripheral.

D. If your twisted pair cable is terminated to wall jacks,

check to see that the pin connections are straight through
from end to end. If so, connect the Model 400 (pig-tail
version) to the controller/computer and the remote
peripheral.

AT&T standard modular color codes

4

1 - Blue
2 - Yellow
3 - Green
4 - Red
5 - Black
6 - White

1 - Blue
2 - Orange
3 - Black
4 - Red
5 - Green
6 - Yellow
7 - Brown
8 - Slate

3.0 INSTALLATIO

NN

Patton’s Model 400 units are easy to install and should give you
years of trouble-free service. Here are a few simple instructions to
help you get things hooked up right.

A. Since these units work in pairs—you must have one unit

at each end of your twisted pair cable run.

B. If your twisted pair cable is unterminated, follow these

installation steps:

1. Obtain a small flat head screwdriver. Insert the
blade in the slot on the side of the Model 400’s case.
Twist gently to pop the case open.

2. Strip about 1 inch of the outside insulation from the
twisted pair cable. Strip 1/4 inch of insulation from
each wire.

3. Insert the wire ends into the screw terminals and
tighten down the screws in the terminal block onto
the exposed wires.

4. Bring the wire out of the side of the case and snap
the two case halves shut.

5. Connect the Model 400s to the controller/computer
and the remote peripheral.

C. If your twisted pair cable is terminated with RJ-11 or

RJ-45 plugs, follow these steps:

1. If the twisted pair cable is terminated into plugs,
check to see that the pin configuration of the twisted
pair cable is not crossed from end to end. The

cable should be wired straight through.

2. If the Model 400s are being connected to telephone
jacks by way of modular jumper cables, check to see
that the polarity is not reversed as the wires pass
from the Model 400s to the wall plates, and through
the building’s wiring network.

3

APPENDIX A

SPECIFICATIONS

Connectors: Male or female BNC for RG62 A/U (93 ohm) coax

connections; RJ-11/45 jack, terminal block, RJ-11/RJ-45 plug on 6
foot twisted pair pig-tail for twisted pair connection

Applicable Hardware: IBM 3274 Type A controller, IBM 3178, 3278

terminals (plus other “clone” equipment)

Range: 1500 feet on 22 gauge wire, 1200 feet on 24 gauge wire

(lengths may vary with actual hardware used)

Transmission Protocol: Transparent to user
Data Bandwidth: 500 Kbps - 5 Mbps
Link-to-Data Isolation: 500 volts AC/DC
Operating Temperature: 32° to 130°F
Storage Temperature: 0° to 185°F
Humidity: To 95% non-condensing
Dimensions: 1.75”l x 1.0”d

5