Patton electronics IPLink 2603, 2620, IPLink 2620 Quick Start Manual
IPLink™ Model 2603 & 2620
WAN Access Router
Quick Start Guide
Document Number: 03323U7-001 Rev. B
Part Number: 07M2620-QS
Revised: October 4, 2005
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
WARNING
• The IPLink 2603/2620 contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired
by qualified service personnel.
• An approved external power supply that incorporates a disconnect
device shall be used and positioned within easy reach of the operator.
• For AC powered units, the power cable used to connect the power
supply shall meet all applicable standards for the country in which it
is to be installed, and be connected to a wall outlet which has
earth ground.
• Hazardous network voltages are present in WAN ports regardless of
whether power to the unit is ON or OFF. To avoid electric shock, use
caution when near WAN ports. When detaching the cables, detach the
end away from the 2603/2620 first.
• Do not work on the system or connect or disconnect cables during
periods of lightning activity.
1.0 Power up the router
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
CAUTION
Your router comes with one of the following power supply options:
•
External AC adaptor with included power cord
Internal AC power supply
•
Internal DC power supply—no power accessories are included
•
1.1 Models with external AC adaptor
1.
Connect female plug of the AC power cord to the AC adaptor provided.
2.
Connect the barrel-type connector of the AC adaptor to the barrel-type
3.
Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).
1.2 Models with internal AC power supply
Power
jack on the IPLink router.
1.
Insert the female end of the AC power cord into the internal power supply connector.
2.
Connect the male end of the power cord into an AC power outlet (100–240 VAC).
2
IPLink 2603 & 2620 Quick Start Guide
1.3 Models with internal DC power supply
Link
Frame
TD
RD
Link
100M
Tx
Rx
WAN Ethernet
Power
Console
ipLink Gateway
High Speed WAN Access Router
Model 2603
1.
Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to the IPLink.
2.
Connect the ground terminal from the power source to the ground terminal on the IPLink.
3.
Connect the negative (-) terminal from the power source with to the negative (-) terminal on the IPLink.
4.
Connect the positive (+) terminal from the power source with to the positive (+) terminal on the IPLink.
1.4 Power-up indication
The
Power
LED blinks as the IPLink is powering up. When the
Power
LED stops blinking and remains lit, the
IPLink is ready for you to configure.
2.0 Configure the IP address
The IPLink is shipped with a factory-configured IP address assigned to the
address is
192.168.200.10/24
. In most cases, you must change the address to be on the same subnet as your
Ethernet
LAN port (green outline). The
PC, as described in the procedures below. If you are not sure which IP address to use for your installation, contact
your network administrator.
2.1 Connecting a PC and logging in
1.
Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port
to the IPLink’s
Console
port (see
Connect to Console port
figure 1
).
PC with
terminal emulator
Serial port
2.
Start a HyperTerminal session on the PC using the settings:
9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
3.
Log in to the IPLink using the factory-default login and password:
Login:
Password: superuser
Login successful
IPLink 2603 & 2620 Quick Start Guide
superuser
Figure 1.
Connecting IPLink to the PC’s serial port
3
Loading...