Patton electronics 1050patton, 1050 User Manual

USER
MANUAL

MODEL 1050

AC Powered, Asynchronous
Short Range Modem

SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com

Part #07M1050-B
Doc. #058031B
Revised 7/30/97

CERTIFIED

An ISO-9001

Certified Company

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1050 components to be
free from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and
does not cover customer damage, abuse or unauthorized modification.
If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or
consequential damages arising from the use of or inability to use this
product. Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1050 generates and uses radio frequency energy, and if
not installed and used properly—that is, in strict accordance with the
manufacturer's instructions—may cause interference to radio and
television reception. The Model 1050 has been tested and found to
comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation. However, there is no guarantee that
interference will not occur in a particular installation. If the Model 1050
does cause interference to radio or television reception, which can be
determined by disconnecting the RS-232 interface, the user is
encouraged to try to correct the interference by one or more of the
following measures: moving the computing equipment away from the
receiver, re-orienting the receiving antenna, and/or plugging the
receiving equipment into a different AC outlet (such that the computing
equipment and receiver are on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Patton
Technical Support.

1

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Service at [phone]; http://www.patton.com: or,

[e-mail].

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 1050. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

2

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions or problems
arise during installation or use of this product, please do not hesitate to
contact Patton Electronics Technical Support at [phone].

2.1 FEATURES

• Asynchronous RS-232 Operation

• Data Rates to 38,400 bps

• Distances up to 7 miles (ll.2 km)

• Point-to-Point or Multipoint Operation

• Optical Isolation

• Loopback Tests

• Tri-State LED Indicators

• DCE/DTE switch selectable

• Carrier Selectable for “Constantly On” or “Controlled by RTS”

• Both RJ-11 and

Terminal Block Line Connectors

• Ultra-Compact Enclosure

• Externally Powered

2.2 DESCRIPTION

The Patton Model 1050 AC Powered Asynchronous Short Range
Modem is to our AC powered short haul line what the Model 1000 is to

our interface powered line–a basic short haul at a great price! And the
Model 1050 has the key features

you need: optical isolation, a local
loopback test mode, LED indicators and a DCE/DTE switch. The
Model 1050 supports asynchronous RS-232 data rates to 38.4 Kbps.
Distances of 7 miles (11.2 km) (@ 1200 bps) are attainable over two
24 AWG (.5mm) twisted pair.

Housed in an ultra-compact metal enclosure, the Model 1050 offers a
choice of line connections: both external RJ-11 jack and internal
terminal block are provided. On the RS-232 side, a female DB-25 is
standard. The Model 1050 is designed for point-to-point or multipoint
applications, and is also compatible with the Patton 1060 and 1226
short hauls.

3

3.0 CONFIGURATION

The Model 1050 may be configured for a wide variety of
asynchronous RS-232 applications. This section will tell you how to
access and set the internal DCE/DTE switch and the internal carrier
control strap. WAIT. Before attempting to re-configure the Model 1050,
check the Default Configuration Table (below) to see if the factory
settings are correct for your application.

3.1 ACCESSING THE MODEL 1050 PC BOARD (see Note 1)

To access the internal PC board, simply remove the two screws at
the rear of the unit and slide the PC board and rear panel out of the
case. Figure 1 (below) shows the location of the DCE/DTE switch and
the RTS strap on the PC board.

4

Figure 1. Switch/Strap locations on Model 1050 PC board.

DEFAULT 1050 CONFIGURATION TABLE

Switch (Strap) Factory Setting Result

DTE/DCE Switch DCE Model 1050 is set to connect to

DTE device (PC, Terminal, etc.)

Carrier Control Strap Pegs 1 & 2 Carrier is “Controlled by RTS”

Carrier Control Strap

DCE/DTE Switch

DCE

123

DTE