Patton electronic 4940 User Manual

SmartNode 4940 Series

Multi-Port T1/E1/PRI
Enterprise VoIP Media Gateway

Quick Start Guide

Part Number: 07MSN4940-QS, Rev. A
Revised: June 13, 2011

Sales Office: [phone]

Technical Support: [phone]

E-mail: [e-mail]

WWW: www.patton.com

WARNING

• Do not open the device when the power cord is connected. For sys­tems without a power switch and without an external power
adapter, line voltages are present within the device when the power
cord is connected.

• For devices with an external power adapter, the power adapter shall
be a listed Limited Power Source The mains outlet that is utilized to
power the device shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker in compli­ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all
applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2
& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet
(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are
rated for proper voltage, current, anticipated temperature, flammabil­ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages
present regardless of whether the device is powered ON or OFF.
PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,
xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net­work voltages” and to avoid electric shock use caution when working
near these ports. When disconnecting cables for these ports, detach
the far end connection first.

• Do not work on the device or connect or disconnect cables during periods

of lightning activity.

In accordance with the requirements of council directive 2002/96/EC on
Waste of Electrical and Electronic Equipment (WEEE), ensure that at end­of-life you separate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recycling.

This device contains no user serviceable parts. This device can only be
repaired by qualified service personnel.

WARNING

2 SmartNode 4940 Series Quick Start Guide

Electrostatic Discharge (ESD) can damage equipment and impair electrical
circuitry. It occurs when electronic printed circuit cards are improperly
handled and can result in complete or intermittent failures. Do the follow-

CAUTION

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac­ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good
skin contact. Connect the clip to an unpainted surface of the chassis
frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap
and cord must operate effectively. If no wrist strap is available,
ground yourself by touching the metal part of the chassis.

1.0 Power up the SmartNode

1. Insert the barrel type connector end of the AC power cord into the external power supply connector.

2. Insert the female end of the power cord into the internal power supply connector.

3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-

tact Patton to replace it with a compatible power cord.

4. Connect the male end of the power cord to an appropriate power outlet.

5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready

to configure.

SmartNode 4940 Series Quick Start Guide 3

2.0 Configuring the desired IP address

2.1 Factory-default IP settings

The factory default configuration for the Ethernet interface IP addresses and netmasks are listed in table 1. The
Ethernet 0/0 port uses DHCP client to get the IP address and netmask automatically from the service provider.

Table 1. Factory default IP address and network mask configuration

Item IP Addresss Network Mask

Ethernet 0 (ETH 0/0) DHCP DHCP

3.0 Connecting the SmartNode to the network

The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flam­mability, and mechanical serviceability.

CAUTION

The SmartNode 4940 Series provides an auto-MDX feature for the Ethernet port, so you can use a straight­through or cross-over cable to connect to a host or a switch (see figure 1).

0

/
3

0

/
2

0

/
1

T

0

1

/

/

0

E

1

E

T

H

0

/
1

C

o
n

s

Reset

o
l

LAN

e

R

S

­2

3

2

LAN (ETH 0/0)

Figure 1. Connecting the SmartNode to the network

You can check the connection with the ping command from the SmartNode to another host on the local LAN.

172.16.1.99(if-ip)[LAN]#ping <IP Address of the host>

4 SmartNode 4940 Series Quick Start Guide