Patton SmartNode 4970 Series, SmartNode 4980 Series, SmartNode 4990 Series Quick Start Manual

SmartNode 4970/4980/4990 Series

Multi-Port T1/E1/PRI
Enterprise VoIP Gateway,
Gateway-Router, IAD

Quick Start Guide

This is a Class A device and is not intended for use in a residential environment.

Part Number: 07MSN4970-80-90-QS, Rev. A
Revised: May 24, 2012

Sales Office: [phone]

Technical Support: [phone]

E-mail: [e-mail]

WWW: www.patton.com

WARNING

• Do not open the device when the power cord is connected. For sys­tems without a power switch and without an external power
adapter, line voltages are present within the device when the power
cord is connected.

• For devices with an external power adapter, the power adapter shall
be a listed Limited Power Source The mains outlet that is utilized to
power the device shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker in compli­ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all
applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2
& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet
(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are
rated for proper voltage, current, anticipated temperature, flammabil­ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages
present regardless of whether the device is powered ON or OFF.
PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,
xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net­work voltages” and to avoid electric shock use caution when working
near these ports. When disconnecting cables for these ports, detach
the far end connection first.

WARNING

WARNING

• Do not work on the device or connect or disconnect cables during peri­ods of lightning activity.

This device contains no user serviceable parts. This device can only be
repaired by qualified service personnel.

This device is NOT intended nor approved for connection to the PSTN. It
is intended only for connection to customer premise equipment.

In accordance with the requirements of council directive 2002/96/EC on
Waste of Electrical and Electronic Equipment (WEEE), ensure that at end­of-life you separate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recycling.

2 SmartNode 4970/4980/4990 Series Quick Start Guide

Electrostatic Discharge (ESD) can damage equipment and impair electrical
circuitry. It occurs when electronic printed circuit cards are improperly
handled and can result in complete or intermittent failures. Do the follow-

CAUTION

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac­ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good
skin contact. Connect the clip to an unpainted surface of the chassis
frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap
and cord must operate effectively. If no wrist strap is available,
ground yourself by touching the metal part of the chassis.

1.0 Power up the SmartNode

1. Insert the barrel type connector end of the AC power cord into the external power supply connector.

2. Insert the female end of the power cord into the internal power supply connector.

3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-

tact Patton to replace it with a compatible power cord.

4. Connect the male end of the power cord to an appropriate power outlet.

5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready

to configure.

2.0 Configuring your SmartNode

Refer to the following manuals (available online at www.patton.com/manuals) for detailed information
about installing, configuring, operating, and troubleshooting the SmartNode:

•

SmartNode Model 4970 Series User Manual: www.patton.com/manuals/SN4970.pdf

•

SmartNode Model 4980/4990 Series User Manual: www.patton.com/manuals/SN4980-90.pdf

SmartNode 4970/4980/4990 Series Quick Start Guide 3

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:[e-mail] with a VoIP SIP client
Online support: www.patton.com
E-mail support: [e-mail]—answered within 1 business day
Telephone support:

•

Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to
2200 UTC/GMT)

•

Alternate: [phone] (Switzerland), Monday–Friday: 9:00 am to 5:30 pm CET (08:00 to 16:30
UTC/GMT)

Fax: [phone] (USA) or [phone] (Switzerland)

B.0 Appendix—Factory default settings

B.1 SmartNode 4970

Username: administrator

Password: (blank)

IP Address: DHCP

Network Mask: n/a

B.2 SmartNode 4980 & 4990

Username: administrator

IP Address (Eth 0/0): DHCP

Network Mask (Eth 0/0): n/a

IP Address (Eth 0/1): 192.168.1.1 (DHCP Server)

Network Mask (Eth 0/1): 255.255.255.0

4 SmartNode 4970/4980/4990 Series Quick Start Guide

C.0 Compliance Information

C.1 Compliance

EMC Compliance:

•

EN55022, Class A

•

EN55024

Safety Compliance:

•

IEC/EN 60950-1, 2nd edition

PSTN Compliance:

•

ACTA (Part 68)

•

IC CS-03

•

AS/ACIF S016:2001

•

AS/ACIF S038:2001

•

ETSI TBR 12, TBR 12/A1 & TBR 13

•

TBR 4

•

TNA 117: 1992

•

TNA 134: 1997

•

PTC 220

SmartNode 4970/4980/4990 Series Quick Start Guide 5

C.2 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of
this equipment is a label that contains—among other information—a product identifier in the format US:
AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com­pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If
the equipment is causing harm to the telephone network, the telephone company may request that you discon­nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser­vice commission or corporation commission for information.

C.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con­firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra­tion was performed based on a Declaration of Conformity indicating that Industry Canada technical speci­fications were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,
operational and safety requirements. The Department does not guarantee the equipment will operate to the
user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. In some cases, the company’s inside wiring associated with a single line individual service
may be extended by means of a certified connector assembly (telephone extension cord). The customer should
be aware that compliance with the above condition may not prevent degradation of service in some situations.
Repairs to some certified equipment should be made by an authorized maintenance facility designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for
their own protection that the ground connections of the power utility, telephone lines and internal metallic water
pipe system, are connected together. This protection may be particularly important in rural areas.

6 SmartNode 4970/4980/4990 Series Quick Start Guide

C.4 CE Declaration of Conformity

Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele­vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility and Directive 2006/95/EC
relating to electrical equipment designed for use within certain voltage limits. The Declaration of Conformity
may be obtained from Patton Electronics, Inc at www.patton.com/certifications

.

The safety advice in the documentation accompanying this device shall be obeyed. The conformity to the above
directive is indicated by CE mark on the device.

C.5 Authorized European Representative

D R M Green
European Compliance Services Limited.
Avalon House, Marcham Road
Abingdon,
Oxon OX14 1UD, UK

SmartNode 4970/4980/4990 Series Quick Start Guide 7

Copyright statement

Copyright © 2012, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-
ment are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the user manual for your SmartNode model,
available online at www.patton.com/manuals.

8 SmartNode 4970/4980/4990 Series Quick Start Guide