Patton SL4050-B2-E, SL4050-B12-E User Manual

Page 1
SL4050/B12/E
SmartLink Series 12-Line VoIP SIP Phone
SL4050/B2/E
SmartLink Series 2-Line VoIP SIP Phone
Quick Start Guide
Part Number: Revised:
September 11, 2008
This is a Class B device and is intended for use in a light industrial or residential environment. It is not intended nor approved for use in an industrial environment. The Model SL4050 phones are not approved for, and are not intended for, direct connection to the Public Switched Telephone Network (PSTN).
07MSL4050B-QS, Rev. A
Sales Office:
Technical Support:
+1 (301) 975-1000 +1 (301) 975-1007
E-mail:
support@patton.com
WWW:
www.patton.com
Page 2
WARNING
This device contains no user serviceable parts. The equipment
shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel.
The external power adapter shall be a listed Limited Power Source. Ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground. The mains outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily acces­sible, and protected by a circuit breaker.
Do not work on the system or connect or disconnect cables
during periods of lightning activity.
In accordance with the requirements of council directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end­of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling.
2
SmartLink 4050 Series Quick Start Guide
Page 3

1.0 Before you begin

The VoIP SIP phone can be set up using the keypad and a web browser, such as Internet Explorer. If you pur­chased this product to make a VoIP call, you must have either an Ethernet-based Cable or a DSL modem with an active connection to the Internet.

1.1 Check your package contents

The following items are included in the SmartLink 4050/B12 and SmartLink 4050/B2 packaging. Contact your supplier immediately if an item is missing.
SmartLink 4050/B12 VoIP SIP Phone SmartLink 4050/B2 VoIP SIP Phone
Ethernet cable, 5-foot (1.5-meter), Qty: 1
\
Power Adaptor
SmartLink 4050 Series Quick Start Guide
SmartLink documentation CD-ROM
Wall/Desk mounting plate
3
Page 4

1.2 Overview of the SL4050/B12/E key functions

2x16 Characters LED Display
LED Indicator
M1
M2
Mute/Func
Transfer
Redial
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
Hold
SPEAKER
Voice Message
Down
Cancel/Left
Phone Book
Numeric Keypad
Phone Book
2
1
ABC3DEF
4
GHI5JKL6MNO
7
8
TUV
PQRS
0@#
.
*
OKCancel
Menu
9
WXYZ
Item Description
2 x 16 LCD Display Displays menu, time, clock, name, phone number, call status LED Indicator Indicates that phone is currently in use or ringing Up Cycle through the phone menu, adjust volume 3-Way Conference Enable 3-way conference OK/Right Confirm setting change, exit menu, dial, save changes Menu Access the phone menu Mute/Function Disable user's microphone so that the person on the other line can not hear anything,
access the language selection, access the time format Transfer Transfer the person you are currently having a conversation to another line Redial/Call History Redial last dialed number, access redial menu Hold Place the person on the other line on hold, answer call waiting Speaker Phone Enable user to use the phone without using the handset Voice Message Check voice message Down Cycle through the phone menu, adjust volume Cancel/Left Deny changes, cancel phone calls, ignore phone calls, backspace Phone Book Access the phonebook Numeric Keypad Input IP/phone number/alphabet characters Local Multiline Switch to different lines
Up 3-Way Conference
OK/Right
Menu Local Multi-Line
Mute/Function
Transfer
Redial/Call History
Hold Speaker Phone
4
SmartLink 4050 Series Quick Start Guide
Page 5

1.3 Overview of the SL4050/B2/E key functions

Voice Message
Down
Cancel/Left
Phone Book
Phone Book
OKCancel
Menu
2x16 Characters LED Display
LED Indicator
Up 3-Way Conference
OK/Right
Menu
Numeric Keypad
Item
2
1
ABC3DEF
4
GHI5JKL6MNO
7
8
TUV
PQRS
0
.
@
*
Speaker
9
WXYZ
#
Mute/Func
Transfer
Redial
Hold
Description
Mute/Function
Transfer
Redial/Call History
Hold
Speaker Phone
2 x 16 LCD Display Displays menu, time, clock, name, phone number, call status LED Indicator Indicates that phone is currently in use or ringing Up Cycle through the phone menu, adjust volume 3-Way Conference Enable 3-way conference OK/Right Confirm setting change, exit menu, dial, save changes Menu Access the phone menu Mute/Function Disable user's microphone so that the person on the other line can not hear anything,
access the language selection, access the time format Transfer Transfer the person you are currently having a conversation to another line Redial/Call History Redial last dialed number, access redial menu Hold Place the person on the other line on hold, answer call waiting Speaker Phone Enable user to use the phone without using the handset Voice Message Check voice message Down Cycle through the phone menu, adjust volume Cancel/Left Deny changes, cancel phone calls, ignore phone calls, backspace Phone Book Access the phonebook
SmartLink 4050 Series Quick Start Guide
5
Page 6
1.4 Numeric Keypad Definitions
You can use alphanumeric characters to enter details into the Phone Book, to create text and e-mail messages. The table below shows the characters that you can enter in the different text modes.
Key
1
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
Text Mode
Normal (ABC) Numeric (0-9) Normal (ABC) Numeric (0-9)
1 pqrsPQRS 7
abcABC 2 tuvTUV 8
defDEF 3 wxyzWXYZ 9
ghiGHI 4 @ . _ * # ()
jklJKL 5 . *
Key
7
PQRS
8
TUV
9
WXYZ
0
@
% & + / $ ,
.
Text Mode
0
*
mnoMNO 6 #
#
6
SmartLink 4050 Series Quick Start Guide
Page 7

2.0 Installing the VoIP SIP phone

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flam­mability, and mechanical serviceability.
CAUTION
Plug one end of the Ethernet cable included with the VoIP SIP phone into the WAN port on the SIP phone
1
(see
figure 1
for SL4050/B12/E or
cable into the xDSL modem or cable modem (or into an optional router or hub).
Do not work on the system or connect or disconnect cables during periods of lightning activity.
WARNING
figure 2
on page 8 for SL4050/B2/E). Plug the other end of the
Power adapter
Ethernet Cable (included with
SL 4050/10 phone)
Router/Hub
(optional)
Internet or
optional WAN
Figure 1.
SmartLink 4050 Series Quick Start Guide
DC IN 5V
3
Power Cable LAN RX TX
WAN LAN
1
Cable/xDSL
modem
Connecting the SL4050/B12/E SIP Phone
SmartLink 4050/10 VoIP SIP Phone
2
Ethernet Cable (optional)
PC (optional)
7
Page 8
If you will not be connecting a PC to the phone, go to step 3. Otherwise, connect an Ethernet cable into
2
3
the LAN port of the SIP phone (see
figure 1
on page 7 for SL4050/B12/E or
figure 2
for SL4050/B2/
E). Plug the other end of the cable into the Ethernet port on the PC.
SmartLink 4050/B2 VoIP SIP Phone
LAN WAN
DC IN 5V
Power adapter
12
Ethernet Cable (optional)
PC (optional)
Figure 2.
Connecting the SL4050/B2/E SIP Phone
Ethernet Cable (included with
SL 4050/2 phone)
Router/Hub
(optional)
X
XT R
N A L
e l
b a C
r e
w o P
Cable/xDSL
modem
Plug the power adapter barrel connector into the power connector on th SIP phone (see page 7 for SL4050/B12/E or
figure 2
for SL4050/B2/E). Plug the other end of the power adapter into
an AC electrical outlet.
3
Internet or
optional WAN
figure 1
on
8
SmartLink 4050 Series Quick Start Guide
Page 9

3.0 Setting up the VoIP SIP phone

Press the MENU key
Display Name: Your name
ADSL DIALUP: ENABLE
ADSL ID: My_ADSL_ID
ADSL Password: ********
IP Address: AUTO
Subnet Mask: AUTO
Router IP: AUTO
ADSL DIALUP: ENABLE/DISABLE
DHCP: ENABLE/DISABLE
DNS Server IP:
010.000.000.001
SNTP Server IP:
220.130.158.52
DisableEnable
ADSL DIALUP: DISABLE
DisableEnable
IP Address:
010.000.000.100
Subnet Mask:
255.255.255.000
Router IP:
010.000.000.254
ENABLE/DISABLE – select enable or disable
A
UTO – IP address given by
the router or ISP
SNTP Server IP – IP or URL
SmartLink 4050 Series Quick Start Guide
Figure 3.
Menu summary, page 1 of 2
9
Page 10
SNTP Cycle: 01
Do Not Disturb: ENABLE/DISABLE
CF Unconditional: ENABLE/DISABLE
CF User Busy: ENABLE/DISABLE
CF No Answer: ENABLE/DISABLE
Anonymous Call: ENABLE/DISABLE
Anony Call Rej: ENABLE/DISABLE
Ringing Type: Ringing 1~4/5~8/9
Ringing 1~9
1~4: Tone 5~8: Melody 9: MP3
10
WAN MAC Address: 00D0E9123456
M2 Setting: Line
LAN MAC Address: 00D0E9123457
Press the MENU key
Version: V: 01.31
UPDATE CHANGES? <OK> OR <CANCEL>
Figure 4.
M2 ~ M12
Type: Line/Park One Touch Dial/ Extension
Menu summary, page 2 of 2
SmartLink 4050 Series Quick Start Guide
SL4050/B12
Model Only
Page 11

4.0 Logging in to the web interface

The configuration menu can be accessed using a web browser.
1.
Open a web browser (Internet Explorer, Netscape Navigator, or equivalent).
2.
Type in the IP address of the phone followed by:
Note
The IP address is provided by your Internet service provider (ISP). If your ISP supports DHCP, you can obtain the IP address from your phone.
Mute/Func
Press + to get the IP address. You can also login from the LAN port with
192.168.15.1:9999
9
4
WXYZ
GHI
.
9999
(for example
http://192.168.1.1:9999
http://
).
The login window displays (see
3.
Enter a
User Name
and
figure 5
Password
Figure 5.
. Leave the user name and password blank if you are installing the
phone for the first time.
4.
Click OK. The following screen displays after logging in:
).
Login window
SmartLink 4050 Series Quick Start Guide
Figure 6.
Main window
11
Page 12

4.1 Network Settings - DHCP

Click on Dynamic host configuration protocol (DHCP) for IP address information that is obtained automatically from your ISP. The
DNS Server
information is obtained from your ISP.
Figure 7.

4.2 Network Settings - PPPoE

Select
PPPoE
if your ISP uses PPPoE. Most DSL users use PPPoE.
Figure 8.
PPPoE ID:
PPPoE Password: DNS Server 1-2:
PPPoE ID/username provided by your ISP
Password for the PPPoE ID
DNS address provided by your ISP
DHCP configuration window
PPPoE configuration window
12
SmartLink 4050 Series Quick Start Guide
Page 13

4.3 Network Settings - Static IP

Select
Static IP
if all Wide Area Network IP information is provided to you by your ISP.
Figure 9.
IP Address: IP address assigned to you by your ISP
Router IP: Router IP address
Subnet Mask: Subnet mask
DNS Server 1-2: DNS server address provided by your ISP
Note
RESTART
the system for new settings to take effect after you modify the IP address.
Static IP configuration window
SmartLink 4050 Series Quick Start Guide
13
Page 14

4.4 SIP Settings

Click on
SIP Settings to display the configuration window (see
figure 10
). Session initiation protocol (SIP) is the most popular VoIP standard. It enables two or more people to make phone calls, share multimedia, and make multimedia conference over the Internet.
Note
You should have an administrator set up these settings for you or obtain the information directly from your SIP service provider.
Figure 10.
SIP Phone Port Number:
Registrar Server Domain Name/IP Address:
Registrar Server Port Number:
Authentication Expire Time:
SIP phone listening port
Registrar server listening port
The time that the SIP registration expires. The phone must send SIP REGIS-
SIP Settings window
Registrar server domain name or IP address.
TER to keep the registration at half of the setting time.
Outbound Proxy Domain Name/IP Address:
Outbound Proxy Port Number:
Send messages via Outbound Proxy: Select Enable to send all SIP requests through Outbound Proxy
Outbound proxy listening port
Outbound proxy domain name or IP address.
14
SmartLink 4050 Series Quick Start Guide
Page 15

4.5 SIP Account Settings

Click on SIP Account Settings to display the configuration window (see figure 11). You can have up to four accounts—that is, the SIP phone can receive calls from up to four different phone numbers.
Figure 11. SIP Account Settings window
Default Account: When you dial a number, the default account is used to dial. User Name of default account
is displayed on the receiver's IP phone.
Account Active: Enable or disable this account.
Display Name: Name displayed on the LCD of called party.
SIP User Name: The number in the URI displayed on the LCD for the caller.
Authentication User Name: User name to log into the SIP server.
Authentication Password: Password to log into the SIP server.
Ringer Type: Eight types of tone and melody can be selected for the specified account
Register Status: Displays if the current phone is registered or unregistered with SIP server.
SmartLink 4050 Series Quick Start Guide 15
Page 16

5.0 Making a phone call

SPEAKER
8
TUV
SPEAKER

5.1 Dialing an IP address

1. Lift the handset or press the SPEAKER button.
2. Dial an IP address. For example, to dial 192.168.0.1 press:
9
1
WXYZ
3. Press or wait until the timer expires to dial.
OK
2
ABC
.
*
6
1
MNO
.
*

5.2 Dialing a SIP number

Note You must register with a SIP server before using a SIP number.
1. Lift the handset or press the SPEAKER button.
2. Dial a SIP number. For example, to dial 1866 press
6
1 8
TUV
3. Press or wait until the timer expires to dial.
OK
6
MNO
MNO
0
@
*
1
.
16 SmartLink 4050 Series Quick Start Guide
Page 17

6.0 Operating the Internet Radio

1. Press to turn on the Internet radio.
2. Press and to choose a preferred station.
3. Press to turn off the Internet radio.
Phone Book
Cancel
6.1 Key Definitions for Internet Radio
Key Definition Key Definition
Turn on the Internet Radio Increase / decrease the volume
Menu
Phone Book
Cancel
OK
Pause / Play Display the name of the current station
Turn off the Internet Radio Tune the Internet Radio to the preferred
station
Numeral
Keys
The ten numeral keys 0, 1~9 are the quick access keys to the first ten preferred stations on web config­uration “Music Station”.

6.2 About Internet Radio

All the keys related to the Internet Radio are described in the table above. Those key functions will only be
available when the phone is hung up. If the phone is hung on, those key functions will back to the original designed which has stated in Page.7.
When the phone is receiving the incoming call, the Internet Radio function will be turned off automatically.
When the user picks up the handset or presses “SPEAKER” to make a phone call, the Internet Radio will be
also turned off automatically.
Please turn off the Internet Radio before you do the next steps as below:
Use pre-dialing to make a phone call
Enter MENU to configure
Access Phone Book
Adjust the Ringer Volume
When the user is listening to the Internet Radio, the phone will have the current song and singer's name
showing on the screen.
SmartLink 4050 Series Quick Start Guide 17
Page 18

7.0 Additional Information

The complete SmartLink 4050 Getting Started Guide is located on the CD-ROM that came with your SIP phone. It can also be downloaded for viewing from www.patton.com.
A.0 Compliance Information
A.1 Compliance
EMC:
FCC Part 15, Class B
EN55022, Class B
EN55024
Safety:
EN60950-1
PSTN Regulatory Compliance:
FCC Part 68
CS-03
AS/ACIF S004
AS/ACIF S040
A.2 Radio and TV Interference (FCC Part 15)
This equipment generates and uses radio frequency energy, and if not installed and used properly-that is, in strict accordance with the manufacturer's instructions-may cause interference to radio and television reception. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by disconnecting the cables, try to correct the interference by one or more of the following mea­sures: moving the computing equipment away from the receiver, re-orienting the receiving antenna, and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).
A.3 CE Declaration of Conformity
We certify that the apparatus identified in this document conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of their conformity.
18 SmartLink 4050 Series Quick Start Guide
Page 19
The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device.
A.4 Authorized European Representative
D R M Green, European Compliance Services Limited. Oakdene House, Oak Road , Watchfield, Swindon, Wilts SN6 8TD, UK
A.5 FCC Part 68 (ACTA) Statement
This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains-among other information-a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone com­pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If the equipment is causing harm to the telephone network, the telephone company may request that you discon­nect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser­vice commission or corporation commission for information.
A.6 Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con­firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra­tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
This Declaration of Conformity means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations. Repairs to some certified equipment should be made by an authorized maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the ground connections of the power utility, telephone lines and internal metallic water pipe system, are connected together. This protection may be particularly important in rural areas.
SmartLink 4050 Series Quick Start Guide 19
Page 20

Copyright statement

Copyright © 2008, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no
liability for errors that may appear in this document.

Trademarks statement

The term SmartLink is a trademark of Patton Electronics Company. All other trademarks presented in this docu- ment are the property of their respective owners.

Patton support headquarters in the USA

Online support: Available at www.patton.com
E-mail support: E-mail sent to support@patton.com will be answered within 1 business day
Telephone support: Standard telephone support is available five days a week—from 8:00 am to
5:00 pm EST (1300 to 2200 UTC/GMT)—by calling +1 (301) 975-1007
Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call sip:support@patton.com
Fax: +1 (253) 663-5693

Alternate Patton support for Europe, Middle East, and Africa (EMEA)

Telephone support: Standard telephone support is available five days a week—from 8:00 am to
5:00 pm CET (0900 to 1800 UTC/GMT)—by calling +41 (0)31 985 25 55
Fax: +41 (0)31 985 25 26
Note For additional service and support information, refer to the “Contacting Patton for assistance” chapter
of the SmartLink 4050 Series Getting Started Guide located on the CD-ROM that came with your SIP phone or available online at www.patton.com.
For additional warranty, trademark, compliance, and technical support information, refer to the SmartLink 4050 Series Getting Started Guide located on the CD-ROM that came with your SIP phone or available online at www.patton.com.
20 SmartLink 4050 Series Quick Start Guide
Loading...