SmartNode 4654 and 4658 Series
ADSL2+ Multiport ISDN VoIP IAD
Quick Start Guide
Important
intended nor approved for use in an industrial or residential environment.
Approval —This device is approved for connection to the public ISDN telecommunication network,
over BRI/S0-ISDN interfaces.
Zulassung —Zugelassen für die Anschaltung an das öffentliche ISDN Telekommunikationnetz an
BRI/S0-ISDN Schnittstellen.
Aprobación —Este aparato está aprobado para conexión a red publica ISDN sobre interfaz BRI/S0.
Approbation —Cet appareil est approuve pour la connexion au reseau ISDN public avec les interfaces
BRI/S0.
Document Number: 13225U7-002 Rev. A
Part Number: 07MSN4650A-QS
Revised: June 12, 2008
—This is a Class A device and is intended for use in a light industrial environment. It is not
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
2
WARNING
•
The SmartNode contains no user serviceable parts. The equipment shall
be returned to Patton Electronics for repairs, or repaired by qualified
service personnel.
•
Mains Voltage: Do not open the case when the power cord is connected.
For systems without a power switch, line voltages are present within
the power supply when the power cord is connected. The mains outlet
that is utilized to power the SmartNode router shall be within 10 feet
(3 meters) of the device, shall be easily accessible, and protected by a
circuit breaker
•
For AC powered units, ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it
is connected to a wall outlet which has earth ground.
•
For units with an external power adapter, the adapter shall be a listed
Limited Power Source.
•
Hazardous network voltages are present in WAN ports regardless of
whether power to the SmartNode is ON or OFF. To avoid electric shock,
use caution when near WAN ports. when detaching the cables, detach
the end away from the SmartNode first.
•
Do not work on the system or connect or disconnect cables during periods of lightning activity.
1.0 Power up the SmartNode
1. Connect the SmartNode to the mains (AC) power source with the power cable.
2. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready
to configure.
2.0 Connecting the SmartNode to your laptop PC
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
CAUTION
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide
3
–
+
1
2
V
,
1
.2
5
A
A
C
T
L
I
N
K
Straight-through wired cable
LAN (ETH 0/0)
Laptop PC
Figure 1. Connecting to the PC
1. Connect the PC’s Ethernet port to LAN (ETH 0/0) port of the SmartNode 4650 ADSL2+. The SmartNode
4650 ADSL2+ Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through Ethernet
cables for host or hub/switch connections. (See figure 1 .)
2. The SmartNode comes with a built-in DHCP server to simplify configuration. Therefore, to automatically
configure the PC for IP connectivity to the SmartNode, configure the laptop PC for DHCP. The SmartNode
will provide the PC with an IP address.
3. Check the connection to the SmartNode by executing the ping command from the PC command window
as follows:
ping 192.168.1.1
3.0 Configuring the desired IP address
3.1 Factory-default IP settings
The factory default configuration for the Ethernet interface IP addresses and netmasks are listed in table 1 .
Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP
server. The WAN interface uses DHCP client to get the IP address and netmask automatically from the
service provider.
Table 1. Factory default IP address and network mask configuration
Item
WAN interface DSL port (DSL 0/0)
DHCP DHCP
LAN interface Ethernet 1 (ETH 0/0) 192.168.1.1 255.255.255.0
DHCP server address range (LAN) 192.168.1.10-192.168.1.19 255.255.255.0
If these addresses match with those of your network, go to section 4.0 “Connecting the SmartNode to the
network” on page 4. Otherwise, continue with the following sections to change the addresses and
network masks.
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide
IP Addresss Network Mask
4
3.2 Login
1. To access the SmartNode, start the Telnet application on your PC. Type the default IP address into the
address field: 192.168.1.1 . Accessing your SmartNode via a Telnet session displays the login screen.
Type the factory default login: administrator and leave the password empty. Press the Enter key after the
password prompt.
login: administrator
password:<Enter>
192.168.1.1>
2. After you log in, your SmartNode will be running in operator execution mode (indicated by > character
in the command line prompt). To enter configuration mode, use the commands enable and configure .
192.168.1.1> enable
192.168.1.1# configure
192.168.1.1(cfg)#
3.3 Changing the WAN IP address
1. To modify IP configuration settings, you must enter context IP mode. Enter the following command:
192.168.1.1(cfg)# context ip router
192.168.1.1(ctx-ip)[router]#
2. Now you can set your IP address and network mask for the interface ETH 0/0(WAN) . In this example a
network 172.16.1.0/24 is assumed. The IP address in example is set to 172.16.1.99 . (You should set it
to the IP address that the network provider has given you.)
Note The examples in this guide use a private IP network with the network address 172.16.1.0/24 .
192.168.1.1(ctx-ip)[router]# interface eth_dsl
192.168.1.1(if-ip)[eth_dsl]# ipaddress 172.16.1.99 255.255.255.0
2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.
2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.
172.16.1.99(if-ip)[eth_dsl]#
3. Copy this modified configuration to your new start-up configuration. This will store your changes in non-
volatile memory. On the next start-up the system will initialize itself using the modified configuration.
172.16.1.99 (if-ip)[eth_dsl]# copy running-config startup-config
172.16.1.99 (if-ip)[eth_dsl]#
The SmartNode can now be connected to your network.
4.0 Connecting the SmartNode to the network
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
CAUTION
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide
Loading...