intended nor approved for use in an industrial or residential environment.
Document Number: 03321U7-001 Rev. B
Part Number: 07M3201-QS
Revised: October 15, 2008
—This is a Class A device and is intended for use in a light industrial environment. It is not
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
WARNING
CAUTION
•
This device contains no user serviceable parts. The equipment
shall be returned to Patton Electronics for repairs, or repaired
by qualified service personnel.
•
The external power adapter shall be a listed Limited Power
Source. The mains outlet that is utilized to power the devise
shall be within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker.
•
If an AC power adapter is used, ensure that the power cable
used meets all applicable standards for the country in which it
is to be installed, and that it is connected to a wall outlet which
has earth ground.
•
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is ON or OFF. To avoid electric
shock, use caution when near WAN ports. When detaching the
cables, detach the end away from the device first.
•
Do not work on the system or connect or disconnect cables
during periods of lightning activity.
1.0 Power up the router
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
Your G.SHDSL router comes with one of the following power supply options:
•
External AC adaptor with included power cord
External DC power supply
•
1.1 Models with external AC adaptor
1.
Connect female plug of the AC power cord to the AC adaptor provided.
2.
Connect the barrel-type connector of the AC adaptor to the
3.
Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).
2
Power
DiamondLink 3201 & 3241 Quick Start Guide
connector on the DiamondLink router.
Input: 36–60VDC, 0.13A
(SELV)
( + N/C - )
Power Su
le
Terminal
block
tr +)
( C
A
, 1
ly
p
p
u
t: 5V
le
u
u
d
r S
tp
o
e
u
M
w
O
o
A
P
3
- )
C
.1
D
/C
)
V
, 0
V
8
L
C
N
4
E
D
( +
V
(S
0
–6
6
ut: 3
p
In
(-) Terminal
(+) Terminal
Figure 1.
48VDC power supply
1.2 Models with external DC power supply
1.
Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to the 48VDC
power supply terminal block (see
2.
Connect the negative (-) terminal from the power source with to the negative (-) terminal on
figure 1
).
the power supply.
3.
Connect the positive (+) terminal from the power source with to the positive (+) terminal on
the power supply
4.
Connect the 48VDC output barrel-type plug to the
Power
connector on the DiamondLink.
1.3 Power-up indication
The
Power
LED blinks as the DiamondLink is powering up. When the
Power
LED stops blinking and remains lit,
the DiamondLink is ready for you to configure.
2.0 Configure the IP address
The DiamondLink is shipped with a factory-configured IP address assigned to the
line). The address is
192.168.200.10/24
. In most cases, you must change the address to be on the same subnet
as your PC, as described in the procedures below. If you are not sure which IP address to use for your installation, contact your network administrator.
DiamondLink 3201 & 3241 Quick Start Guide
Ethernet
LAN port (green out-
3
2.1 Connect a PC and log in
1.
Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port
to the on the DiamondLink’s (red)
Console
port (see
figure 2
).
PC with
Line
Ethernet
MDI-X
Console
Power
terminal emulator
Serial port
Connect to Console port
(red port)
Figure 2.
2.
Start a HyperTerminal session on the PC using the settings:
Connecting DiamondLink to the PC’s serial port
9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
3.
Log in to the DiamondLink using the factory-default login and password:
Login:
Password: superuser
Login successful
superuser
2.2 Modify the IP address
1.
Display current IP interface settings for the DiamondLink
→→
→→
ip list interfaces <enter>
IP Interfaces:
ID | Name | IP Address | DHCP | Transport