Patton 3088A User Manual

OnSite™ Model 3088A Series

G.SHDSL.bis CPE with Fixed
Serial Interfaces

Quick Start Guide

Important

intended nor approved for use in an industrial or residential environment.

REGULATORY MODEL NUMBER: 03340D4-001

Part Number: 07M3088A-QS, Rev. A
Revised: February 2, 2012

—This is a Class A device and is intended for use in a light industrial environment. It is not

Sales Office: [phone]

Technical Support: [phone]

E-mail: [e-mail]

WWW: www.patton.com

WARNING

• Do not open the device when the power cord is connected. For sys­tems without a power switch and without an external power
adapter, line voltages are present within the device when the power
cord is connected.

• For devices with an external power adapter, the power adapter shall
be a listed Limited Power Source The mains outlet that is utilized to
power the device shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker in compli­ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all
applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2
& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet
(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are
rated for proper voltage, current, anticipated temperature, flammabil­ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages
present regardless of whether the device is powered ON or OFF.
PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,
xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net­work voltages” and to avoid electric shock use caution when working
near these ports. When disconnecting cables for these ports, detach
the far end connection first.

• Do not work on the device or connect or disconnect cables during peri­ods of lightning activity.

This device is NOT intended nor approved for connection to the PSTN. It
is intended only for connection to customer premise equipment.

WARNING

In accordance with the requirements of council directive 2002/96/EC on
Waste of Electrical and Electronic Equipment (WEEE), ensure that at end­of-life you separate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recycling.

2 Model 3088A Series Quick Start Guide

1.0 Select configuration method

Before powering up, you must select one of the following methods for configuring your OnSite:

•

Plug ‘n’ Play—The OnSite comes factory-configured for Plug ’n’ Play configuration when connected to a
service-provider network.

•

DIP Switch—For deploying the OnSite in back-to-back applications. To use DIP-switch configuration you
must first set the DIP switches to a position other than all OFF or all ON before powering-up the OnSite. To
configure your CPE using the DIP switches, refer to the section entitled “Hardware (DIP-switch) configuration”
in the OnSite Model 3088A Series Getting Started Guide.

•

Software Configuration—Allows you to modify configurable parameters by connecting a PC to the con­sole port and issuing software commands. To use software configuration you must set all the DIP switches to
the ON position before powering-up the OnSite. To configure your CPE via the console port, refer to section
“Software (CLI) configuration” in the OnSite Model 3088A Series Getting Started Guide.

2.0 Power up the CPE

Your G.SHDSL.bis CPE comes with one of the following power supply options:

•

External AC adaptor with detachable power cord

•

External DC power supply with terminal block connector (model 48V-PSM3)

2.1 Models with external AC adaptor

1. Connect female plug of the AC power cord to the AC adaptor provided.

2. Connect the barrel-type connector of the AC adaptor to the Power connector on the OnSite.

3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).

2.2 Models with external DC power supply

The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 3088A. The black and red leads
plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel power supply jack
on the 3088A. (See figure 1).

To Power

Supply Jack

S/N: G01234567890

MADE IN CHINA BY SUNNY

Barrel power connector

Figure 1. DC Power Supply

Model 3088A Series Quick Start Guide 3

MODEL : SYD1106-0505

INPUT : 36-60V 0.2A MAX

OUTPUT : +5V 1.0A

OUTPUT POWER : 5W MAX

SWITCHING POWER SUPPLY

-Vin

+Vin

To -48VDC

Source

Black lead (-V)

Red lead (+V)

Link

Activity

TM / ERR

Terminal

DSL

Power

Figure 2. Model 3088A/CA front panel

2.3 Power up indication

Verify that the Power LED (see figure 2) illuminates and remains lit.

3.0 Connect the G.SHDSL port

1. Obtain single-twisted-pair cable with an RJ-45 plug connector at each end.

2. Plug one end of the cable into the RJ-45 socket (labelled DSL) on the OnSite CPE.

— If you are connecting to a DSL service, plug the other end of the cable into the RJ-45 wall

socket that provides your G.SHDSL service.

— If connecting to another OnSite, verify the other end of the cable is connected to the DSL port

on other OnSite and the DSL port is correctly configured.

3. When a DSL link is established, the front-panel DSL LED will turn on.

4.0 Connect the serial port

Your OnSite comes with one of the following serial WAN ports for connection to an CPE:

•

RS-232 (DB-25F)—Model 3088A/A

•

V.35 (DB-25F)—Model 3088A/CA

•

X.21 (DB-15)—Model 3088A/D

•

E1 (120-Ohm RJ-48C and dual 75-Ohm BNC connectors)—Model 3088A/K

4 Model 3088A Series Quick Start Guide

Connect the serial cable to the OnSite serial port as follows:

1. Attach the male connector of the serial cable to the female serial connector on the OnSite.

2. Attach the other end of the cable to the serial connector on the local serial CPE.

Note You can connect the V.35 interface to an M/34 connector using Patton’s Model 2-34F25M

interface adapter.

Note You can configure the E1 interface to either recover the network clock from the E1 line or supply the

network clock for the E1 line.

5.0 Additional information

For detailed information about installing, configuring, operating, and troubleshooting, refer to the Model 3088A
Series Getting Started Guide at www.patton.com/manuals/3088A.pdf.

A.0 Compliance Information

A.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety:

•

UL 60950-1/CSA C22.2 N0. 60950-1

•

IEC/EN60950-1

•

AS/NZS 60950-1

1.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in
strict accordance with the manufacturer's instructions—may cause interference to radio and television recep­tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor­dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable
protection from such interference in a commercial installation. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment causes interference to radio or television reception,
which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol­lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,
and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and
receiver are on different branches).

Model 3088A Series Quick Start Guide 5

1.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con­firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra­tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications
were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,
operational and safety requirements. The Department does not guarantee the equipment will operate to the
user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. In some cases, the company’s inside wiring associated with a single line individual service
may be extended by means of a certified connector assembly (telephone extension cord). The customer should
be aware that compliance with the above condition may not prevent degradation of service in some situations.
Repairs to some certified equipment should be made by an authorized maintenance facility designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for
their own protection that the ground connections of the power utility, telephone lines and internal metallic water
pipe system, are connected together. This protection may be particularly important in rural areas.

A.4 EC Declaration of Conformity

(See section A.5 “EG-Konformitätserklärung” for German version.)

Product Description: OnSite 3088A Series

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws
of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition
of their conformity.

The safety advice in the documentation accompanying the products shall be obeyed.
The conformity to the above directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.

A.5 EG-Konformitätserklärung

(see section A.4 “EC Declaration of Conformity” for English version)

Produktbezeichnung: OnSite 3088A Sendereihe

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol­gender Richtlinie überein:

R&TTE 1999/5/EG

Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige
Anerkennung ihrer Konformität.

6 Model 3088A Series Quick Start Guide

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.
Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem
Gerät bestätigt.

Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/

certifications/.

A.6 Authorized European Representative

D R M Green
European Compliance Services Limited.
Oakdene House, Oak Road
Watchfield,
Swindon, Wilts SN6 8TD, UK

Copyright statement

Copyright © 2012, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term OnSite is a trademark of Patton Electronics Company. All other trademarks presented in this document
are the property of their respective owners.

Patton support headquarters in the USA

•

Online support: Available at www.patton.com

•

E-mail support: E-mail sent to [e-mail] will be answered within 1 business day

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm EST (1300 to 2200 UTC/GMT)—by calling [phone]

•

Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call sip:[e-mail]

•

Fax: [phone]

Alternate Patton support for Europe, Middle East, and Africa (EMEA)

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm CET (0900 to 1800 UTC/GMT)—by calling [phone]

•

Fax: [phone]

Note For additional service and support information, refer to the “Contacting Patton for assistance” chapter

of the OnSite 3088A Getting Started Guide available online at www.patton.com/manuals/

3088A.pdf.

Model 3088A Series Quick Start Guide 7

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the OnSite 3088A Getting Started Guide available
online at www.patton.com/manuals/3088A.pdf.

8 Model 3088A Series Quick Start Guide