Front panel switches for loops
and test patterns
RJ-48C
network connector
V.35, EIA-530, or
10Base-T interfaces
Power from universal
AC inputs or -48 VDC
LEDs display network, data, and
diagnostic status at-a-glance
2U-high rack card has the
same features and interfaces
as the Model 2720
Control port
The Patton 2720 T1 CSU/DSU terminates T1 and Fractional T1 services, and
converts to V.35, EIA-530, and 10Base-T Ethernet
Connect to Any Terminal Interface
Eliminates Routers
Smooth clock V.35 and EIA-530
connection, and 10Base-T Ethernet
Bridge Ethernet across the WAN using
industry standard PPP/BCP
VT-100 Control Port With Full DS0 Mapping
nx56/nx64 channel selection from
64 kbps to 1.544 Mbps
Full Diagnostics Included
V.52 511 BERT, 2047, QRSS, V.54 loopbacks,
and CO loop-up/loop-down diagnostics
Standalone or Rack Solutions
Available to suit your needs: small
desktop unit, or high density rack cards
Power it Anywhere
Universal input AC (90-240V), and
-48 VDC power supply options
NETLINK™ ACCESS PRODUCTS
ne of the smallest and most economical CSU/DSUs available,
the Model 2720 is loaded with features usually found in more
expensive units: flexible clocking modes, AMI/B8ZS coding,
diagnostics, and nx56/nx64 rates—all easily configurable
through switches or VT-100 console.
The Model 2720 series terminates T1/FT1 services for all nx56/nx64 kbps to
1.544 Mbps rates and connects to the customer’s router, FRAD, CODEC,
and LAN with V.35, RS-530, or 10Base-T interfaces. Front panel LEDs and
switches allow for instant diagnostics and service monitoring. Use the VT-100
console port for complete command and control over your T1 termination.
AC or DC power options make installing the Model 2720 into your network
infrastructure a snap.
The wide variety of features, compact size, and low price make Patton’s T1
CSU/DSUs the right solution for your next network challenge. For more
information, visit us at www
.patton.com.
O
Network Termination Unit
Patton 2720 T1 and Fractional T1 CSU/DSU
Model 2720 Model 2710RC
DTE Interface
Power Supplies
Dimensions
Weight
Line Rate
Line Connector
Line Coding
Line Framing
DS0 Start Position
Line Build-Out
DTE Interface
DTE Rates
Clocking
Diagnostics
Compliance
Temperature/Humidity
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Phone +1-301/975-1000
Fax +1-301/869-9293
E-mail marketing@patton.com
URL www.patton.com
07MD2720-DS1
Application—LAN-to-LAN without a router
1.544 Mbps (T1/FT1)
RJ-48C (100 ohms)
AMI or B8ZS
D4 or ESF
Any position, contiguous/non-contiguous mapping when configured via VT-100 console
Receiver: automatic. Transmitter: 0, -7.5, -15, -22.5 dB, DSX-1 level
V.35 (M/34 female), EIA-530 (DB-25 female), or 10Base-T Ethernet (RJ-45 female)
nx56/nx64 kbps (V.35, EIA-530); nx56/nx64 kbps to 10Base-T (10 Mbps)
Smooth clocking—internal, external, or network
V.54 local/remote loop; responds to CO-initiated loop-up and loop-down codes. ESF line-loop and payload FDL messages. Diagnostics patterns: 511, 2047, and QRSS
FCC Part 15 Class A and Part 68. AT&T 62411, TR54016, ANSI T1.403
32 to 122°F (0 to 50°C)/5 to 90% relative humidity, non-condensing
UI (100–240 VAC) or -48 VDC
1.50 H x 4.17 W x 5.84 D inch (3.84 H x 10.6 W x 14.84 D cm)
1.0 lbs (0.45 kg)
AC or DC rack power supplies
3.0 H x 0.83 W x 7.84 D inch (7.6 H x 2.1 W x 19.0 D cm)
0.31 lbs (0.14 kg)
Netlink T1/FT1 product family
V.35 EIA-530 10Base-T
Connecting a remote LAN to headquarters has never been easier—or more economical! Place one Model 2720/I at each LAN location,
use MAC and PPP/BCP bridging in the Model 2720s to provide seamless LAN-to-LAN connection over the wide-area T1 network.
2720/C
2720/B
2720/I
V.35 EIA-530 10Base-T
2710RC/A/I
2710RC/B/B
2710RC/C/IA
Loading...