USER
MANUAL
MODEL 2010
Asynchronous to
Synchronous
Converter
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
http://www.patton.com
Part# 07M2010-A
Doc# 062031UA
Revised 03/21/94
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 2010 components to be
free from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials, and
does not cover customer damage, abuse or unauthorized modification.
If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or
consequential damages arising from the use of or inability to use this
product. Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 2010 generates and uses radio frequency energy, and if
not installed and used properly—that is, in strict accordance with the
manufacturer's instructions—may cause interference to radio and
television reception. The Model 2010 has been tested and found to
comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation. However, there is no guarantee that
interference will not occur in a particular installation. If the Model 2010
does cause interference to radio or television reception, which can be
determined by disconnecting the RS-232 interface, the user is
encouraged to try to correct the interference by one or more of the
following measures: moving the computing equipment away from the
receiver, re-orienting the receiving antenna and/or plugging the
receiving equipment into a different AC outlet (such that the computing
equipment and receiver are on different branches).
1.2 SERVICE
All warranty and non-warranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Service at (301) 975-1007.
Packages received without an
RMA number will not be accepted.
Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 2010. Technical Service hours: 8AM to 5PM EST, Monday
through Friday.
1
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for one year parts and labor. If any questions or problems
arise during installation or use of this product, please do not hesitate to
contact Patton Electronics Technical Support at (301) 975-1007.
2.1 FEATURES
• Conforms to CCITT V.14 and V.22 standards
• Adapts asynchronous terminals to synchronous modems and
multiplexers
• Allows character lengths from 8 - 11 bits
• Requires no AC power or batteries
• Data rates to 19.2 Kbps
• Automatically adjusts synchronous data rates
• Miniature size
• Accepts external clocking
• Made in the USA
2.2 DESCRIPTION
The Model 2010 converter gives asynchronous hardware access to
the high speed capabilities of synchronous modems or multiplexers.
The Model 2010 plugs directly into the asynchronous RS-232 DTE port
and connects via RS-232 cable to the synchronous DCE device.
Drawing power from the RS-232 interface, the Model 2010 needs
no AC power or batteries to operate and supports data rates to 19.2
Kbps. Because the Model 2010 automatically adjusts the synchronous
data rate to match the asynchronous DTE’s output rate, no data rate
strapping is necessary. The Model 2010 derives clocking externally
from the clock of the synchronous DCE, and imposes no limit on data
block size. Characters may be up to 11 bits long.
Measuring only 3.2” x 2.0” x .75”, the Model 2010 is housed in a
sturdy ABS plastic case. It comes fully equipped with a DB-25 male
connector and a DB-25 female connector.
2
Loading...