For Quick
Start Installation
Model 1195/8E1
Optical Multiplexer
Getting Started Guide
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
Part Number: 07M1195-GS, Rev. A
Revised: February 12, 2009
Patton Electronics Company, Inc.
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Tel: +1 (301) 975-1000
Fax: +1 (301) 869-9293
Support: +1 (301) 975-1007
Web: www.patton.com
E-mail: support@patton.com
Copyright © 2009, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document.
Warranty Information
The software described in this document is furnished under a license and may be used
or copied only in accordance with the terms of such license.
Patton Electronics warrants all 1195 components to be free from defects, and
will—at our option—repair or replace the product should it fail within one year from
the first date of the shipment.
This warranty is limited to defects in workmanship or materials, and does not cover
customer damage, abuse or unauthorized modification. If the product fails to perform
as warranted, your sole recourse shall be repair or replacement as described above.
Under no condition shall Patton Electronics be liable for any damages incurred by the
use of this product. These damages include, but are not limited to, the following: lost
profits, lost savings and incidental or consequential damages arising from the use of or
inability to use this product. Patton Electronics specifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed
an acceptance of these terms by the user.
3
Summary Table of Contents
1 General information...........................................................................................................................................13
2 Applications overview ........................................................................................................................................21
3 Model 1195/8E1 installation..............................................................................................................................23
4 Connecting the RS-232 port ..............................................................................................................................29
5 CLI configuration...............................................................................................................................................34
6 GUI configuration ..............................................................................................................................................47
7 Contacting Patton for assistance.......................................................................................................................66
A Specifications .....................................................................................................................................................69
B Connector pinouts .............................................................................................................................................74
4
Table of Contents
Safety when working with electricity ............................................................................................................11
General observations .....................................................................................................................................11
General conventions ......................................................................................................................................12
1 General information...........................................................................................................................................13
Model 1195/8E1 Overview...................................................................................................................................14
Features and Benefits ...........................................................................................................................................14
Front View............................................................................................................................................................15
Rear View.............................................................................................................................................................20
2 Applications overview ........................................................................................................................................21
Typical Model 1195/8E1 Application......... ........................................................................................................22
3 Model 1195/8E1 installation..............................................................................................................................23
Connecting power ................................................................................................................................................24
AC Power .......................................................................................................................................................24
DC Power .......................................................................................................................................................24
Grounding ......................................................................................................................................................25
Connecting the optical interface...........................................................................................................................26
Connecting the DB-37 connector.........................................................................................................................27
Connecting E1 links .............................................................................................................................................28
Definition for E1 Interfaces ...........................................................................................................................28
Connecting Ethernet Links...................................................................................................................................28
Verifying the connection ...............................................................................................................................28
Definition for Ethernet Interfaces ..................................................................................................................28
4 Connecting the RS-232 port ..............................................................................................................................29
Connecting the RS-232 port.................................................................................................................................30
RS-232 port cable details ...............................................................................................................................31
RS-232 pin definition ....................................................................................................................................31
Configuring HyperTerminal.................................................................................................................................32
5 CLI configuration...............................................................................................................................................34
General Commands..............................................................................................................................................35
Specific Commands..............................................................................................................................................37
Check current MAC address of the device ....................................................................................................37
Check the current IP address of the device ....................................................................................................37
Check gateway address of the device ............................................................................................................37
View the get / getnext community of SNMP .................................................................................................37
Configure the get / getnext community of SNMP .........................................................................................37
View the set community of SNMP ................................................................................................................38
Configure set community of SNMP ..............................................................................................................38
Change the IP address of the device ..............................................................................................................38
Change the Subnet mask information of the device ......................................................................................38
5
Model 1195 Getting Started Guide Table of Contents
Change the Gateway information of the device ............................................................................................38
Change the MAC address of the device ........................................................................................................39
Show system information ..............................................................................................................................39
Enable / Disable the loopback of E1 Port ......................................................................................................40
Check whether the E1 Port is looped back ....................................................................................................40
Check the alarms of E1 Tributary ..................................................................................................................41
Configure laser port receive mode .................................................................................................................41
View the current status of laser port ..............................................................................................................42
Reset the system ............................................................................................................................................42
Set / configure the default settings in the device ...........................................................................................42
Enable / Disable the Ethernet Port .................................................................................................................42
Set / configure the Ethernet Port performance parameters ............................................................................43
Check the Ethernet Port configuration ..........................................................................................................43
View the performance of ethernet port ..........................................................................................................44
View the status of ethernet port .....................................................................................................................44
Clear the performance statics / log of Ethernet, E1, GFP ..............................................................................44
Add a telnet user ............................................................................................................................................45
Delete a Telnet user .......................................................................................................................................45
Check the list of Telnet users .........................................................................................................................45
View the status of remote system power .......................................................................................................45
Mask the unused e1 alarms ............................................................................................................................45
View the configuration of unused e1 alarm mask .........................................................................................45
Clear the record of E1's CV alarm .................................................................................................................46
Configure the status of alarm tone mask .......................................................................................................46
View the status of alarm tone mask ...............................................................................................................46
6 GUI configuration ..............................................................................................................................................47
Overview ..............................................................................................................................................................48
Installing the GUI.................................................................................................................................................48
Accessing the 1195......... .....................................................................................................................................49
Adding/Removing a System.................................................................................................................................49
Adding a system ............................................................................................................................................49
Removing a system ........................................................................................................................................50
Editing a system .............................................................................................................................................50
Communicating With a System............................................................................................................................51
Adding/Removing Users......................................................................................................................................52
Adding a user .................................................................................................................................................52
Removing a user ............................................................................................................................................52
Editing a user entry ........................................................................................................................................52
Status Monitoring.................................................................................................................................................53
System Monitoring...............................................................................................................................................54
Start/stop monitoring .....................................................................................................................................54
Configure/view alarms ...................................................................................................................................54
Change the Trap Community and/or Port ......................................................................................................54
6
Model 1195 Getting Started Guide
View log ............................................ ...............................................................................................................55
Managing Trap Details.........................................................................................................................................55
Configuring System Settings................................................................................................................................55
Configuring IP Settings ........................................................................................................................................56
Configuring Trap Settings ....................................................................................................................................57
Configuring Default Settings ...............................................................................................................................58
SNMP Community...............................................................................................................................................59
Viewing Settings ..................................................................................................................................................60
Back Up................................................................................................................................................................61
Restore..................................................................................................................................................................61
Synchronize..........................................................................................................................................................62
Report...................................................................................................................................................................62
List of systems ...............................................................................................................................................62
List of traps ....................................................................................................................................................63
Read Me ...............................................................................................................................................................64
System Information..............................................................................................................................................65
Exiting the System ...............................................................................................................................................65
7 Contacting Patton for assistance.......................................................................................................................66
Introduction ..........................................................................................................................................................67
Contact information..............................................................................................................................................67
Patton support headquarters in the USA ........................................................................................................67
Alternate Patton support for Europe, Middle East, and Africa (EMEA) .......................................................67
Warranty Service and Returned Merchandise Authorizations (RMAs)...............................................................67
Warranty coverage .........................................................................................................................................67
Out-of-warranty service ...........................................................................................................................68
Returns for credit .....................................................................................................................................68
Return for credit policy ............................................................................................................................68
RMA numbers ...............................................................................................................................................68
Shipping instructions ...............................................................................................................................68
A Specifications .....................................................................................................................................................69
E1 Interface ..........................................................................................................................................................70
Optical ..................................................................................................................................................................70
Optical Interface Specifications: 1310nm Single Mode ......................................................................................71
Transmitter Optical Characteristics ...............................................................................................................71
Receiver Optical Characteristics ....................................................................................................................71
Optical Interface Specifications: 1550nm Single Mode ......................................................................................71
Transmitter Optical Characteristics ...............................................................................................................71
Receiver Optical Characteristics ....................................................................................................................72
Safety....................................................................................................................................................................72
Ethernet Interface .................................................................................................................................................72
Configuration, Management and Alarms .............................................................................................................72
Power Supply .......................................................................................................................................................72
Environment.........................................................................................................................................................73
7
Model 1195 Getting Started Guide Table of Contents
Physical ................................................................................................................................................................73
B Connector pinouts .............................................................................................................................................74
DB-37 connector pinout (Model 1195/8E1).........................................................................................................75
DB-37 connector pinout details for E1 connections ......................................................................................76
8
List of Figures
1 Model 1195/8E1.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2 1195/8E1 front view .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3 Front LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 Tributary Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Config Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7 1195/8E1 rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Typical application for Model 1195/8E1.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 CD flash screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10 Model 1195/8E1 Main Menu window . . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
11 Add/Remove System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
12 Select COM port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13 Select TCP/IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
14 Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
15 Add user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
16 Status Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
17 System Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
18 System settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
19 E1 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
20 IP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
21 Trap settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
22 Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
23 SNMP Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
24 Show settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
25 Back up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
26 Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
27 Synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
28 View systems report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
29 View traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
30 Readme file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
31 View system information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
32 DB-37 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
33 DB-37 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
About this guide
This guide describes the Model 1195/8E1 hardware, installation and basic configuration.
Audience
This guide is intended for the following users:
• Operators
• Installers
• Maintenance technicians
Structure
This guide contains the following chapters and appendices:
• Chapter 1 on page 13 provides information about features and capabilities
• Chapter 2 on page 21 contains an overview describing the typical application
• Chapter 3 on page 23 provides hardware installation procedures
• Chapter 4 on page 29 provides information for connecting the RS-232 port
• Chapter 5 on page 34 provides information for using the CLI to configure the unit
• Chapter 6 on page 47 provides information for using the GUI to configure the unit
• Chapter 7 on page 66 contains information on contacting Patton technical support for assistance
• Appendix A on page 69 contains technical specifications
• Appendix B on page 74 describes the connector pin-outs
For best results, read the contents of this guide before you install the unit.
9
CAUTION
WARNING
Precautions
Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you
become aware of potential problems. Warnings are intended to prevent safety hazards that could result in personal injury. Cautions are intended to prevent situations that could result in property damage or
impaired functioning.
Note
IMPORTANT
CAUTION
WARNING
A note presents additional information or interesting sidelights.
The alert symbol and IMPORTANT heading calls attention to
important information.
The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the instructions to avoid property damage.
The shock hazard symbol and CAUTION heading indicate a
potential electric shock hazard. Strictly follow the instructions to
avoid property damage caused by electric shock.
The alert symbol and WARNING heading indicate a potential safety hazard.
Strictly follow the warning instructions to avoid personal injury.
The shock hazard symbol and WARNING heading indicate a potential electric
shock hazard. Strictly follow the warning instructions to avoid injury caused
by electric shock.
10
Model 1195 Getting Started Guide Model 1195 Getting Started Guide
Safety when working with electricity
•
This device contains no user serviceable parts. The equipment shall be
returned to Patton Electronics for repairs, or repaired by qualified service
WARNING
personnel.
•
Mains Voltage: Line voltages are present when the power cord is connected. The mains outlet shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker.
For AC powered units, ensure that the power cable used meets all applica-
•
ble standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.
Hazardous network voltages are present in WAN ports, regardless of
•
whether power to the unit is ON or OFF. To avoid electric shock, use caution
when near WAN ports. When detaching the cables, detach the end away
from the unit first.
Do not work on the system or connect or disconnect cables during periods of
•
lightning activity.
For units with an external power adapter, the adapter shall be a listed Lim-
•
ited Power Source.
11
In accordance with the requirements of council directive 2002/
96/EC on Waste of Electrical and Electronic Equipment (WEEE),
ensure that at end-of-life you separate this product from other
waste and scrap and deliver to the WEEE collection system in
your country for recycling.
General observations
• Place the unit on a flat surface and ensure free air circulation
• Avoid exposing the unit to direct sunlight and other heat sources
• Protect the unit from moisture, vapors, and corrosive liquids
12
.
SN
Model 1195 Getting Started Guide
Typographical conventions used in this document
This section describes the typographical conventions and terms used in this guide.
General conventions
The procedures described in this manual use the following text conventions:
Table 1. General conventions
Convention Meaning
Garamond blue type
Futura bold type
Futura bold-italic type Parts of commands, which are related to elements already named by the user, are
Italicized Futura type
Futura type Indicates the names of fields or windows.
Garamond bold type
< > Angle brackets indicate function and keyboard keys, such as <SHIFT>, <CTRL>,
[ ] Elements in square brackets are optional.
{a | b | c} Alternative but required keywords are grouped in braces ({ }) and are separated
screen
node
Indicates a cross-reference hyperlink that points to a figure, graphic, table, or section heading. Clicking on the hyperlink jumps you to the reference. When you
have finished reviewing the reference, click on the Go to Previous View
button in the Adobe® Acrobat® Reader toolbar to return to your starting point.
Commands and keywords are in boldface font.
in boldface italic font.
Variables for which you supply values are in italic font
Indicates the names of command buttons that execute an action.
<C>, and so on.
by vertical bars ( | )
Terminal sessions and information the system displays are in
The leading IP address or nodename of a Model 1195 is substituted with
node in boldface italic font.
The leading SN on a command line represents the nodename of the Model 1195
screen font
# An hash sign at the beginning of a line indicates a comment line.
Chapter 1
Chapter contents
Model 1195..................................................................................................................................14
Features and Benefits....................................................................................................................14
Front View ...................................................................................................................................15
Rear View.....................................................................................................................................20
General information
13
WARNING
14
Model 1195 Getting Started Guide
1 • General information
Model 1195/8E1
Model 1195 FiberLink E1/Ethernet Mux is a point to point high performance optical line transmission
equipment, combines 8, ITU-T G.703 compliant standard electrical E1s plus 100BaseT Ethernet signal into
an optical data stream for transport over fiber optic pairs. Several transmitter options for different cable types
and wave-lengths are available. 1+1 optical path redundancy is offered and available as an option.
Figure 1. Model 1195/8E1
For Testing: Always Install Optical Attenuators. For distances of less than 10
km, optical attentuators must be intalled on the Optical Links. Otherwise, the
optics will be permanently damaged.
Features and Benefits
• Integrated E1 Plus Ethernet Optical Multiplexer
• Compact design that performs E1 and Ethernet channel multiplexing & de-multiplexing to an optical out-
put
• Provides visible and audible alarm indication
• Provide Remote power detection (RPD)
• Low power consumption
• Orderwire (EOW) channel for end to end installation and maintenance
• Local and remote loop back test for diagnostics
• 1+1 Fiber Path protection
• ALS (Auto Laser Shutdown) facility for eye safety
• 10/100M Ethernet Port - 100 Mbps Ethernet data transmission rate complies with IEEE 802.3
• Supports auto negotiation and flow control (pause)
• Clock options: internal/loop-timed
• Provides visible and audible alarm indications
• Local and remote loopback controls for diagnostics and troubleshooting
• Local configuration management through RS232 Serial Port
• Remote configuration and management through 10/100BaseT Ethernet
• Port - Telnet (english text commands)
• SNMP (V1 and V2C)
Model 1195 Overview
15
Model 1195 Getting Started Guide
Front View
TRIBUTARY STATUS Indicator LED’s
E1 LOS
1 2 3 4
5 6 7 8
OFF
R
V_CL
MUTE
C
2
1
ON
Model 1195/8E1 Optical Multiplexer
ALM
PWR
WORKA
RPD
WORKB
CV
NOPA
NOPB
E-3
E-6
E1 LOS
1 2 3 4
5 6 7 8
LOF
MASK
ALS_EN
4
1 • General information
Interfaces and Button
OFF
O
I
ON
MANG
5
4
P 2
P 1
OP
O 6
OP
LOO
LOO
LO
LO
LOOP 3
LO P
2
334
1
5 6 7 8
ETH PHONE
8
7
P
P
O
O
LO
LO
MANG
ETH PHONE
O
I
POWER
POWER
OFF
ON
PWR
CV
ALM
RPD
WORKA
WORKB
NOPA
NOPB
Global Indicator LEDs
Figure 2. 1195/8E1 front view
LOF
E-3
E-6
CLR
CV_
UTE
M
MASK
E
_ N
ALS
2
P
O 1
L O
LOOP
5
4
OP
OP
LO 3
OP
OOP
OOP
L
O 7
O 6
L OP
L
LO 8
L
OFF
ON
3
2
1
2
4
1
3
5 6 7 8
4
Display Select and Config Switches
Front View
16
Model 1195 Getting Started Guide
Model 1195/8E1 Optical Multiplexer
ALM
PWR
RPD WORKB
CV
Name
WORKA
NOPA
NOPB
E1 LOS
LOF
1 2 3 4
E-3
5 6 7 8
E-6
Color Function
PWR Green ON – Unit is powered
ALM Red ON – Local alarm detected
CV Yellow ON – CV alarm
RPD Yellow ON – Remote power off detected
WORKA Green ON – Optical A is working. Optical B indication is off.
WORKB Green ON – Optical B is working. Optical A indication is off.
NOPA Red ON – Optical signal loss is detected on port A.
NOPB Red ON – Optical signal loss is detected on port B.
LOF Red ON – Loss of frame detected at optical port
E-3 Red ON – Line bit error rate is over 10-6 detected at optical port
E-6 Yellow ON – Line bit error rate is over 10-6 detected at optical port
LR
C
TE
OP
O
O
LS_EN
CV_
LO
LO P 2
MU
OFF
2
1
ON
LO P
A
MASK
3
2
3
4
1
PWR
CV
LOOP 4
4
P 8
OP
OP 6
O
LO
LO
LO
LOOP 7
5 6 7 8
ALM
RPD WORKB
MANG
ETH PHONE
WORKA
NOPA
NOPB
O
POWER
I
3
5
1
Figure 3. Front LEDs
OFF – Unit is off
Blinking – Remote alarm detected
OFF – No alarm currently detected
The local alarms take priority over remote alarms.
OFF – No CV alarm
OFF – No RPD alarm
OFF – Optical A is not working.
OFF – Optical B is not working.
Blinking – ALS is enabled on the remote device.
OFF – No loss
Blinking – ALS is enabled on the remote device.
OFF – No loss
OFF – No loss
OFF – No loss
1 • General information
OFF
ON
LOF
E-3
E-6
Front View
17
Model 1195 Getting Started Guide
Model 1195/8E1 Optical Multiplexer
ALM
PWR
WORKA
RPD WORKB
CV
NOPA
NOPB
LOF
E1 LOS
1 2 3 4
E-3
5 6 7 8
E-6
E1 LOS
1 2 3 4
5 6 7 8
Figure . 4 Tributary Status LEDs
OFF
1 • General information
N
K
TE
CV_CLR
MU
2
1
ON
MAS
O
OP 1
S
LO
LO P 2
AL _E
2
334
4
1
OP 3
LO
LOOP 4
LOOP 5
5 6 7 8
OP 7
OP 8
LO
LOOP 6
LO
MANG
ETH PHONE
O
I
POWER
OFF
ON
Name
Color Function
E1-LOS Red ON – E1 signal loss happened at the corresponding tributary
OFF – No loss
Front View
18
Model 1195 Getting Started Guide
Model 1195/8E1 Optical Multiplexer
ALM
PWR
WORKA
RPD WORKB
CV
NOPA
NOPB
LOF
E-3
E-6
E1 LOS
1 2 3 4
5 6 7 8
4
P 8
OP
OO
OOP 7
LO
LOOP 1
LOOP 3
LOOP 2
2
4
3
1
LOOP 6
LOOP 5
5 6 7 8
CLR
CV_
L
E
MUT
L
K
MAS
MANG
ALS_EN
OFF
A
CV_CLR
MUTE
M SK
ALS_EN
3
2
4
1
ON
OFF
2
ON
1
4
Figure . 5 Config Switch LEDs
ETH PHONE
LOOP 2
LOOP 1
2
1
334
3
LOOP
1 • General information
OFF
O
I
ON
POWER
4
LOOP 5
LOOP
5 6 7 8
8
6
OP 7
OOP
OOP
L
LO
L
Name
Function
CV-CLR ON – Clear CV alarm
MUTE ON – Alarm sound is muted. Speaker will sound if any alarms have occurred.
OFF – Speaker will not sound if there are alarms. Note that the ringing of the
order wire cannot be muted.
MASK ON – All current E1 loss alarms will be masked. In addition, alarms will be trig-
gered if a new event of E1 signal loss occurs, even if MASK is ON.
ALS_EN ON – Enable ALS function
OFF – Disable ALS function
LOOP 1-8
ON – Enable remote loopback of E1
OFF – Disable remote loopback of E1
Front View
S.No. Name Description
1. MANG Ethernet Management Interface (RJ-45)
Cable: CAT-5 crossover or straight through
Note: In default Telnet
User Name : superuser (case sensitive)
Password: superuser (case sensitive)
2. ETH Ethernet Interface (RJ-45)
Cable: CAT-5 crossover or straight through
3. PHONE Phone Interface (RJ-11)
Cable: Standard 2-wire cable (64 Kbps, PCM coding)
4. POWER Power Switch
ON – Power ON
OFF – Power OFF
Front View
19
Model 1195 Getting Started Guide 1 • General information
MANG
OFF
ON
POWER
I
O
ETH PHONE
MANG
OFF
ON
POWER
I
O
ETH PHONE
Figure . 6 Interfaces
Model 1195/8E1 Optical Multiplexer
1
1
ON
OFF
R
CV_CL
MUTE
MA
SK
ALS_EN
2
2
334
4
ALM
LOF
E1 LOS
E-3
1 2 3 4
RPD WORKB
NOPB
WORKA
NOPA
L
OO
P 4
L
O 3
O P
L O 2
O P
L O 1
O P
PWR
CV
E-6
5 6 7 8
LOOP 8
LOOP 7
LOO
P 6
LOOP 5
5 6 7 8
Model 1195 Getting Started Guide 1 • General information
Rear View
Figure . 7 1195/8E1 rear view
Optical Interfaces Console and Earth point
DC 48 V
~ 220 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL B
PGND
GND
TX RX
-48V
OPTICAL A
TX RX
OPTICAL A
TX RX
E1 8-5
E1 8-5
CONSOLE
RS232
E1 4-1
II
II
CONSOLE
RS232
E1 4-1
Rear View 20
II
E1 Interfaces
II
E1 InterfacesPower
Chapter 2 Applications overview
Chapter contents
Typical Model 1195 Application..................................................................................................................22
21
Model 1195 Getting Started Guide 2 • Applications overview
Typical Model 1195 Application
Figure 8 shows the typical application for the 1195 model.
Figure 8. Typical application for Model 1195
Typical Model 1195 Application 22
Chapter 3
Model 1195/8E1 installation
Chapter contents
Connecting power .................................................................................................................................................24
AC Power .......................................................................................................................................................24
DC Power .......................................................................................................................................................24
Grounding ......................................................................................................................................................25
Connecting the optical interface ............................................................................................................................26
Connecting the DB-37 connector..........................................................................................................................27
Connecting E1 links..............................................................................................................................................28
Definition for E1 Interfaces ............................................................................................................................28
Connecting Ethernet Links....................................................................................................................................28
Verifying the connection .................................................................................................................................28
Definition for Ethernet Interfaces ...................................................................................................................28
23
Model 1195 Getting Started Guide 3 • Model 1195installation
Connecting power
AC Mains version: Please use the AC main cable (provided) to connect the system to your AC mains power
outlet.
DC Mains version: Please connect the DC mains cable (provided) to the system. The polarity should not be
reversed while connecting. Otherwise, you can get your system damaged.
AC Power
To connect the AC 220V power:
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL A
TX RX
E1 8-5
E1 4-1
CONSOLE
IEC 60320
Male on Unit
DC Power
To connect the DC -48V:
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
IEC 60320
Female
OPTICAL A
TX RX
II
From AC Source
(220V)
E1 8-5
II
II
E1 4-1
II
RS232
CONSOLE
RS232
DC Power
Cable
Connecting power 24
Model 1195 Getting Started Guide 3 • Model 1195 installation
Grounding
When the equipment is used with the AC~220V power supply, the 3-core socket must be grounded for protection.The other equipment, e.g. optical terminal, connected with this equipment must also be grounded
To connect the Earth:
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL A
TX RX
E1 8-5
E1 4-1
CONSOLE
RS232
Eart
inh Po
t
Eart
II
h
e
Wir
II
Connecting power 25
Model 1195 Getting Started Guide 3 • Model 1195 installation
WARNING
Connecting the optical interface
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL A
TX RX
E1 8-5
E1 4-1
CONSOLE
Transmit
Optical Signal
through Optical
Fiber Cable
II
II
RS232
Receive
Optical Signal
through Optical
Fiber Cable
For Testing: Always Install Optical Attenuators. For distances of less than 10
km, optical attentuators must be intalled on the Optical Links. Otherwise, the
optics will be permanently damaged.
Connecting the optical interface 26
Note: Do not expose to the naked eye.
Connect fiber cable to system
when power is OFF.
Model 1195 Getting Started Guide 3 • Model 1195 installation
Connecting the DB-37 connector
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL A
TX RX
E1 8-5
E1 4-1
CONSOLE
19
1
DB-37 (Female)
Connector
II
18
37
II
RS232
1
RJ-45 (F)
Connector
Note See Appendix B on page 74 for DB-37 connector pinouts.
Connecting the DB-37 connector 27
2
RJ-45 (F)
Connector
4xE1 Signals
3
4
RJ-45 (F)
Connector
RJ-45 (F)
Connector
Model 1195 Getting Started Guide 3 • Model 1195 installation
Connecting E1 links
Connect E1 line after ensuring that transmission device have been grounded. A Bit Error Rate (BER) test may
be conducted on E1 Link using a BERT tester to ensure that the E1 errors are within the permitted limits /
threshold.
Definition for E1 Interfaces
The E1 Interface (RJ-45 connector) is defined as:
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8
Rx+ Rx- N/C Tx+ Tx- N/C N/C N/C
Data In + Data In - Data Out + Data Out -
Connecting Ethernet Links
Please configure the Ethernet port of the equipment at both sides as well as the Ethernet Ports of the devices
that are connected to the equipment. Connect the Ethernet links.
Please ensure that the connecting LANs on both sides of the link are operating in the same IP domain.
Verifying the connection
Ping over the Ethernet connection from one side to the other (near-end to the far-end) to verify the link.
Definition for Ethernet Interfaces
The Ethernet Interface (RJ-45 connector) is defined as:
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 8
Tx+ Tx- Rx+ N/C N/C Rx- N/C N/C
Data Out+ Data Out- Data In+ Data In-
Connecting E1 links 28
Chapter 4 Connecting the RS-232 port
Chapter contents
Connecting the RS-232 port .................................................................................................................................30
RS-232 port cable details ................................................................................................................................31
RS-232 pin definition .....................................................................................................................................31
Configuring HyperTerminal .................................................................................................................................32
29
Model 1195 Getting Started Guide 4 • Connecting the RS-232 port
Connecting the RS-232 port
DC 48 V
~ 220 V
PGND
GND
-48V
OPTICAL B
TX RX
OPTICAL A
TX RX
E1 8-5
E1 4-1
CONSOLE
Settings:
1 Bits per second 19200
2 Data bits 8
3 Parity None
4 Stop bits 1
5 Flow control None
II
RS232
DB9 Connector (Male)
DB9 Connector (Female)
PC
Note: RS232 COM Port cable is provided with the system.
Connecting the RS-232 port 30
DB9 (Male)
Connector
DB9 (Female)
Connector
End 1 DB-9 (Female Connector)
End 2 DB-9 (Female Connector)
Type of cable Twisted pair cable - solid conductor
Number of pairs 2
Diameter 24 AWG
Length 3 meters
Connections As per details given below
DB-9 Pin Number Definition
RS-232
2 RS-232 input signal for management
3 RS-232 output signal for management
5 GND
Others NC
Connecting the RS-232 port 31
Model 1195 Getting Started Guide 4 • Connecting the RS-232 port
RS-232 port cable details
RS-232 pin definition
Configuring HyperTerminal
1. Click on the Start button from the task bar on your PC.
2. Select Programs > Accesories > Communications > HyperTerminal. The following screen will be dis-
played:
3. Enter a name for the new connection and click OK. The connection window will be displayed:
Configuring HyperTerminal 32
Model 1195 Getting Started Guide 4 • Connecting the RS-232 port
Model 1195 Getting Started Guide 4 • Connecting the RS-232 port
5. Change the Bits per second option to 19200 and change the flow control option to None.
The COM Properties settings should be:
Bits per second 19200
Data bits 8
Parity None
Stop bits 1
Flow control None
6. Click Apply, then click OK.
7. A new HyperTerminal session screen will display. Press Enter. The system prompt will appear on the
screen. This prompt is generated by the system. Now, you may access/configure the system with the CLI
commands.
Note Remember to save the settings for future use before you exit the HyperTer-
minal window.
Configuring HyperTerminal 33
34
Chapter 5 CLI configuration
Chapter contents
General Commands..............................................................................................................................................35
Specific Commands..............................................................................................................................................37
Check current MAC address of the device ....................................................................................................37
Check the current IP address of the device ....................................................................................................37
Check gateway address of the device ............................................................................................................37
View the get / getnext community of SNMP .................................................................................................37
Configure the get / getnext community of SNMP .........................................................................................37
View the set community of SNMP ................................................................................................................38
Configure set community of SNMP ..............................................................................................................38
Change the IP address of the device ..............................................................................................................38
Change the Subnet mask information of the device ......................................................................................38
Change the Gateway information of the device ............................................................................................38
Change the MAC address of the device ........................................................................................................39
Show system information ..............................................................................................................................39
Enable / Disable the loopback of E1 Port ......................................................................................................40
Check whether the E1 Port is looped back ....................................................................................................40
Check the alarms of E1 Tributary ..................................................................................................................41
Configure laser port receive mode .................................................................................................................41
View the current status of laser port ..............................................................................................................42
Reset the system ............................................................................................................................................42
Set / configure the default settings in the device ...........................................................................................42
Enable / Disable the Ethernet Port .................................................................................................................42
Set / configure the Ethernet Port performance parameters ............................................................................43
Check the Ethernet Port configuration ..........................................................................................................43
View the performance of ethernet port ..........................................................................................................44
View the status of ethernet port .....................................................................................................................44
Clear the performance statics / log of Ethernet, E1, GFP ..............................................................................44
Add a telnet user ............................................................................................................................................45
Delete a Telnet user .......................................................................................................................................45
Check the list of Telnet users .........................................................................................................................45
View the status of remote system power .......................................................................................................45
Mask the unused e1 alarms ............................................................................................................................45
View the configuration of unused e1 alarm mask .........................................................................................45
Clear the record of E1's CV alarm .................................................................................................................46
Configure the status of alarm tone mask .......................................................................................................46
View the status of alarm tone mask ...............................................................................................................46
View the contact details...................................................................................................................46
General Commands
After entering into the application program for CLI commands, press the “?” key in the command line to
get the list of the commands.
Command Description
?/help To get a list of commands for the system
showmac View MAC address
showip View the IP address
showmask View the subnet mask
showgw View the gateway
showsnmpget View the GET/GETNEXT community of SNMP
snowsnmpset View the SET community of SNMP
setsnmpget Configure the GET/GETNEXT community of SNMP
setsnmpset Configure the SET community of SNMP
setip Configure the IP address
setmask Configure the subnet mask information
setgw Configure the gateway information
setmac Configure the Ethernet MAC address
showsysinfo View the system information
sete1loop Enable/Disable the loopback of the E1 port
showe1loop View if the E1 port is looped back
e1alarm View the alarms of E1 tributary
setcvmode Configure the receive mode of the laser port
showlaser View the current status of the laser port
reset Perform a hot restart
setdefault Configure the settings as default
enableport Enable/Disable the Ethernet port
setport Configure the Ethernet port
showport View the Ethernet port configuration
ethperform Clear the perform counter data
ethstatus View Ethernet status
clearperform Clear the perform counter data
adduser Add a manager to TELNET
deluser Delete a user from TELNET
showuser View information of the TELNET manager
showrpd View the status of remote system power detroy alarm
sete1mask Configure the alarm mask of the unused E1 interface
showe1mask View the configuration of unused E1’s alarm mask
clearcv Clear the record of E1’s CV alarm
settonemask Configure the status of the alarm tone mask
showtonemask
showcontact
View the status of alarm tone mask
View the contact details
General Commands 35
Model 1195 Getting Started Guide 5 • CLI configuration
General Commands 36
Model 1195 Getting Started Guide 5 • CLI configuration
For detailed command format, please key "? cmdname" or "help cmdname".
See the following examples:
Command Example Notes
1195#? [cmdname]
{enter}
OR
1195#help [cmdname]
{enter}
1195#? sete1loop
<FORMAT>: sete1loop[E1ID]
[Local_Loop][Remote_Loop]
<EXPLAIN>: Enable/Disable
the loopback of E1 port,
use this command to put
the E1 line into loopback mode or non-loopback mode
<PARAMETER>:
E1ID: <0-8>, 0: All: 1-8:
E1ID
Local_Loop: <0/1>, loop
status (0: non-loop ;1:
loop)
Remote_Loop: <0/1>, loop
status (0: non-loop ;1:
loop)
To get further information about any
command, type the command followed by “?”.
Specific Commands 37
Model 1195 Getting Started Guide 5 • CLI configuration
Specific Commands
Check current MAC address of the device
Check the current IP address of the device
Check current subnet mask of the device
Check gateway address of the device
View the get / getnext community of SNMP
Configure the get / getnext community of SNMP
Command Response Notes
1195#showmac
{enter}
System MAC Address:
00.13.20.E8.86.76
Shows the MAC address of the local
device
Command Response Notes
1195#showip
{enter}
System IP Address:
192.168.0.155
Shows the IP address of the local
device
Command Response Notes
1195#showmask
{enter}
System Subnet Mask:
255.255.255.0
Shows the subnet mask of the local
device
Command Response Notes
1195#showgw
{enter}
System Default Gateway
Address: 192.168.0.1
Shows the Gateway of the local
device
Command Response Notes
1195#showsnmpget
{enter}
System SNMP get community:
public
Shows the GET/GET NEXT community of SNMP of the local device.
Command Response Notes
1195#setsnmpget[string]
{enter}
System SNMP get community:
[string]
Configure the GET/GET NEXT community of SNMP of the local device,
where [string]=0 to 31
Specific Commands 38
Model 1195 Getting Started Guide 5 • CLI configuration
View the set community of SNMP
Configure set community of SNMP
Change the IP address of the device
Change the Subnet mask information of the device
Change the Gateway information of the device
Command Response Notes
1195#showsnmpset
{enter}
System SNMP set community:
public
Shows the SET community of SNMP
of the local device
Command Response Notes
1195#setsnmpset [string]
{enter}
System SNMP set community:
[string]
Configure the SET community of
SNMP of the local device, where
[string]=0 to 31
Command Response Notes
1195#setip [ipaddr]
{enter}
System IP address: [ipaddr]
Change the IP address of the local
device, where [ipaddr]=any valid IP
address
Command Response Notes
1195#setmask [subnetaddr]
{enter}
System subnet mask:
[subnetaddr]
Change the subnet mask of the local
device, where [subnetaddr]=any valid
subnet address
Command Response Notes
1195#setgw [gwaddr]
{enter}
System Default Gateway
Address: [gwaddr]
Change the gateway of the local
device, where [gwaddr]=any valid
gateway address
Specific Commands 39
Model 1195 Getting Started Guide 5 • CLI configuration
Change the MAC address of the device
Show system information
Command Response Notes
1195#setmac [macaddr]
{enter}
MAC Address: [macaddr]
Change the MAC of the local device,
where [macaddr]=any valid MAC
address
Note: A new MAC address will be
activated after a system reset.
Command Response Notes
1195#showsysinfo
{enter}
View the system information.
Includes hardware version, software
version, and status of the interface.
View the system information.
Includes hardware version, software
version, and status of the interface.
Specific Commands 40
Model 1195 Getting Started Guide 5 • CLI configuration
Enable / Disable the loopback of E1 Port
Check whether the E1 Port is looped back
Command Response Notes
1195#sete1loop [E1ID] [local_loop]
[remote_loop]
{enter}
E1ID: <0-8>,0: All; 1-8
:E1ID
Local_Loop: <0/1>, loop
status (0: non-loop ;1:
loop)
Remote_Loop: <0/1>, loop
status (0: non-loop ;1:
loop)
Enable/Disable the loopback of E1
port. Use this command to put the E1
line into loopback mode or non-loopback mode.
Command Response Notes
1195#showe1loop
{enter}
Shows if the E1 port is loopbacked or
not. See example below.
Shows if the E1 port is loopbacked or
not.
Specific Commands 41
Model 1195 Getting Started Guide 5 • CLI configuration
Check the alarms of E1 Tributary
Configure laser port receive mode
Command Response Notes
1195#e1alarm
{enter}
Shows the alarms of E1 tributary. See
example below.
Shows the alarms of E1 tributary.
Command Response Notes
1195#setrcvmode [mode]
{enter}
mode: <1-3>receive
mode(1:force_A;
2:force_B; 3:auto)
Configure laser port receive mode.
Specific Commands 42
Model 1195 Getting Started Guide 5 • CLI configuration
View the current status of laser port
Reset the system
Set / configure the default settings in the device
Enable / Disable the Ethernet Port
Command Response Notes
1195#showlaser
{enter}
View the status of laser interface.
Include alarm status, the config of
receive mode, the current work interface.
View the status of laser interface.
Include alarm status, the config of
receive mode, the current work interface.
Command Response Notes
1195#reset
{enter}
Performs a hot restart. Performs a hot restart.
Command Response Notes
1195#setdefault
{enter}
The default settings have been successfully loaded in the system. Reset
the system.
Configures the default setting in the
system.
Note: You must restart the system
after executing this command.
Command Response Notes
1195#enableport [port]
[Enable/Disable]
{enter}
Port = A
Enable/Disable = B
Enable/Disable the Ethernet port,
where:
A=1 (Ethernet Port No.)
B=0:Disable, 1:Enable
Specific Commands 43
Model 1195 Getting Started Guide 5 • CLI configuration
Set / configure the Ethernet Port performance parameters
Check the Ethernet Port configuration
Command Response Notes
1195#setport [port] [AN] [rate]
[duplex] [flow]
{enter}
Port=A, AN=B, Rate=C, Duplex=D,
Flow=E
Configure the Ethernet port performance parameters, where:
A=1 (Ethernet Port No.)
B=0:AN not done, 1:AN done
C=0:10Mbit/s; 1:100Mbit/s
D=0:half-duplex; 1:full-duplex
E=flow-control capability; 0:disable;
1:enable
Command Response Notes
1195#showport
{enter}
Shows the Ethernet port configuration. See example below.
Shows the Ethernet port configuration.
Specific Commands 44
Model 1195 Getting Started Guide 5 • CLI configuration
View the performance of ethernet port
View the status of ethernet port
Clear the performance statics / log of Ethernet, E1, GFP
Command Response Notes
1195#ethperform
{enter}
View the performance of Ethernet. View the performance of Ethernet.
Command Response Notes
1195#ethstatus
{enter}
View the status of Ethernet. View the status of Ethernet.
Command Response Notes
1195#clearperform [A]
{enter}
Clear the performance of E1, Ethernet, etc...
Clear the performance of E1, Ethernet, etc., where: A=1, 2; 1:all the performance, 2:Ethernet performance
Specific Commands 45
Model 1195 Getting Started Guide 5 • CLI configuration
Add a telnet user
Delete a Telnet user
Check the list of Telnet users
View the status of remote system power
Mask the unused e1 alarms
View the configuration of unused e1 alarm mask
Command Response Notes
1195#adduser [Username]
[Password]
{enter}
TELNET Manage Username:
Username
TELNET Manage Password:
Password
Adds a telnet user, where username=<a string (1-31 Bytes)>, user
login name. Password=<a string (1-
31) Bytes)>, user login password.
Command Response Notes
1195#deluser [Username]
[Password]
{enter}
SUCCESS TO DELETE TELNET
USER!
Deletes a telnet user, where username=any valid username, and password=any valid password.
Command Response Notes
1195#showuser
{enter}
TELNET Manage Username:
superuser
Password : superuser
Shows information of Telnet users.
Command Response Notes
1195#showrpd
{enter}
View the status of remote system
power destroy alarm.
View the status of remote system
power destroy alarm.
Command Response Notes
1195#sete1mask [A]
{enter}
Enable/disable : disable
:0; enable : 1
Configure the alarm mask of unused
E1 interface, where A=0,1 disable : 0;
enable : 1
Command Response Notes
1195#showe1mask
{enter}
View the configuration of unused
E1’s alarm mask.
View the configuration of unused
E1’s alarm mask.
Specific Commands 46
Model 1195 Getting Started Guide 5 • CLI configuration
Clear the record of E1's CV alarm
Configure the status of alarm tone mask
View the status of alarm tone mask
View the contact details
Command Response Notes
1195#clearcv [enable]
{enter}
enable : 1 Clear the record of E1’s CV alarm.
Command Response Notes
1195#settonemask [A]
{enter}
enable/disable : diable : 0 ;
enable : 1
Configure the status of alarm tone
mask, where A=0,1 disable : 0 ;
enable : 1
Command Response Notes
1195#showtonemask
{enter}
View the status of alarm tone mask. View the status of alarm tone mask.
Command Response Notes
1195#showcontact
{enter}
Patton Electronics Company
7622, Rickenbacker Drive
Gaithersburg, MD 20879
Email: support@patton.com
+ (301) 975-1000
View the contact details of the
company.
Chapter 6 GUI configuration
Chapter contents
Overview ...............................................................................................................................................................48
Installing the GUI .................................................................................................................................................48
Accessing the 1195/8E1.......................................................................................................................................49...............
Adding/Removing a System...................................................................................................................................49
Adding a system ..............................................................................................................................................49
Removing a system .........................................................................................................................................50
Editing a system ..............................................................................................................................................50
Communicating With a System.............................................................................................................................51
Adding/Removing Users........................................................................................................................................52
Adding a user ..................................................................................................................................................52
Removing a user ..............................................................................................................................................52
Editing a user entry .........................................................................................................................................52
Status Monitoring .................................................................................................................................................53
System Monitoring................................................................................................................................................54
Start/stop monitoring ......................................................................................................................................54
Configure/view alarms ....................................................................................................................................54
Change the Trap Community and/or Port ......................................................................................................54
View log ..........................................................................................................................................................55
Managing Trap Details..........................................................................................................................................55
Configuring System Settings..................................................................................................................................55
Configuring IP Settings .........................................................................................................................................56
Configuring Trap Settings .....................................................................................................................................57
Configuring Default Settings.................................................................................................................................58
SNMP Community...............................................................................................................................................59
Viewing Settings....................................................................................................................................................60
Back Up ................................................................................................................................................................61
Restore ..................................................................................................................................................................61
Synchronize...........................................................................................................................................................62
Report ...................................................................................................................................................................62
List of systems .................................................................................................................................................62
List of traps .....................................................................................................................................................63
Read Me................................................................................................................................................................64
System Information...............................................................................................................................................65
Exiting the System.................................................................................................................................................65
47
Model 1195 Getting Started Guide 6 • GUI configuration
Overview
This chapter describes how to use the Graphical User Interface (GUI) to access and configure the Model
1195.
Installing the GUI
1. Insert the CD that came with the 1195 into the CD-ROM drive. The CD will automatically start
and display the main window.
Figure 9. CD flash screen
2. Click on Graphical User Interface (GUI) to begin the installation. The Install Wizard window will dis-
play.
3. Click Next to proceed to the next step. Select the “I accept...” option and click Next.
4. Enter your user information and click Next.
5. Review the settings for installing the program and click Install to proceed.
6. A window will display to confirm the installation was completed. Click Finish.
Overview 48
Model 1195 Getting Started Guide 6 • GUI configuration
Accessing the 1195
The Model 1195 GUI helps in configuring the 1195 system through a serial port connection
between the equipment and a PC or to establish a remote login to the equipment. It also allows the user to
configure the system as desired and also provides the information about the status of the system.
To start the GUI, first make a proper connection between the equipment and the computer using a factorysupplied RS-232 cable (DB-9 (Female) to DB-9 (Female) or Ethernet crossover cable provided with the system). Then, open the GUI. The following screen will display:
Figure 10. Model 1195 Main Menu window
Adding/Removing a System
Adding a system
To add a new system:
1. Click on Option at the top of the screen and select Add/Remove System. The following window will
appear:
Accessing the 1195 49
Model 1195 Getting Started Guide 6 • GUI configuration
Figure 11. Add/Remove System
2. Click New. Enter information for all of the fields.
3. Click Add. The system will be added. The GUI supports up to 2,000 systems.
Note When you are entering the information for the new system, assign
the correct IP address of that system. If needed, you can change the
IP address of the system. To change the IP address of the system,
make a local connection (through the COM port), then click on Set-
tings > IP Settings.
Removing a system
There are two ways to remove a system.
Option 1: In the Add/Remove System window, select the system, then select Remove in the Status field. The
entry of the system will be removed temporarily. The entry may be revived later.
Option 2: Click Remove
. The entry will be removed permanently. To add the same system again, you
will need to create a new entry.
Editing a system
To make necessary changes for the current entry, enter the desired changes into the fields in the Add/Remove
System window. Then, click Edit. The current entry will be updated.
Adding/Removing a System 50
Model 1195 Getting Started Guide 6 • GUI configuration
Communicating With a System
To communicate with the system, you have to make a connection with the system through a TCP or COM
port.
To select a COM port:
1. Click on the Option menu at the top of the screen and select TCP/COM (Single System).
Figure 12. Select COM port
2. From the drop-down menu, select the COM port that is in use. The message “COM X is selected” will
display.
3. Click OK.
To access the system remotely, select TCP/IP Winsock.
1. Click on the Option menu at the top of the screen and select Communication (Single System).
Figure 13. Select TCP/IP address
2. From the drop-down menu, select the TCP/IP Winsock.
3. Select the IP address of the equipment in the field REMOTE HOST IP ADDRESS.
Communicating With a System 51
Model 1195 Getting Started Guide 6 • GUI configuration
4. To change the IP address, connect to the system with the COM port using an RS-232 cable.
5. Click on Settings > IP Settings. Click OK. A login window will display.
6. Enter the User Name and Password. Click Submit.
Figure 14. Login
Note User name and password are case sensitive.
Adding/Removing Users
Adding a user
To add a new user, click on Option at the top of the screen and select Add User. A window will display. Click
New. Enter information for all of the fields, then click Add.
Removing a user
To remove a user, select a user from the drop-down menu in the User window. Then, click Remove.
Editing a user entry
To make changes to an existing user, select the user from the drop-down menu in the User window. Make the
desired changes, then click Edit. The current entry will be updated.
Adding/Removing Users 52
Figure 15. Add user
Model 1195 Getting Started Guide 6 • GUI configuration
Status Monitoring
To view the status and current alarms of the 1195 click on Tributary Interface at the top of the screen
and select Status Monitoring.
Figure 16. Status Monitoring
If a status is Red, there is an alarm.
If the status is Green, there is no alarm.
If the status is Yellow, the E1 is under physical loopback.
Status Monitoring 53
Model 1195 Getting Started Guide 6 • GUI configuration
System Monitoring
To monitor the alarms of all the systems present in the network, click on Communication at the top of the
screen and select MultiSystem Monitor (NMS). A list of the systems will display.
Figure 17. System Monitoring
Start/stop monitoring
• To stop monitoring, click Stop Monitor.
• To restart monitoring, click Start Monitor.
Configure/view alarms
To configure or view the detailed alarms of any particular system, click the colored button for any selected system in the system list. The color of the system’s button indicates the status of alarms for the system. Red indi-
cates that there are alarms present on the system. Green indicates that there are currently no alarms found on
the system. Grey indicates that the system cannot be found. Yellow indicates that the application is checking
for alarms for that particular system.
The alarm indicator at the top of the screen indicates if there is any alarm present in any of the systems in the
network.
Change the Trap Community and/or Port
To change the trap community and/or port, you need to stop monitoring first. To stop monitoring, click Stop
Monitor. You can change the community and port with the drop-down menus at the top of the systems list.
After you have made the desired changes, click Start Monitor.
System Monitoring 54
Model 1195 Getting Started Guide 6 • GUI configuration
View log
Click the View Log button at the bottom of the screen to view details of all of the traps received to date.
Note Refresh the systems list to view the most current information.
Managing Trap Details
To view the details of traps for the last ten days, click on Communication at the top of the screen and select
Multisystem Monitoring (NMS). The list of systems will display.
1. Select the duration of traps from Trap View drop down list box at the bottom of the screen.
2. Click OK button. The selected trap will appear in the screen.
Configuring System Settings
To configure settings for the system, click on Settings at the top of the screen and select System Settings. A
window will display where you can make the desired changes.
Managing Trap Details 55
Figure 18. System settings
Model 1195 Getting Started Guide 6 • GUI configuration
To configure settings for E1 and Mask, click on Settings at the top of the screen and select E1 Settings. A window will display where you can make the desired changes.
Figure 19. E1 settings
Configuring IP Settings
To configure settings for IP addresses, click on Settings at the top of the screen and select IP Settings. A window will display where you can make the desired changes.
Configuring IP Settings 56
Model 1195 Getting Started Guide 6 • GUI configuration
Figure 20. IP settings
Note Changing MAC addresses will reset the system.
Configuring Trap Settings
To configure the settings for receiving traps, click on SNMP at the top of the screen and select Trap Settings.
A window will display where you can create a list of monitoring systems to which traps will be sent by the
selected device. The Trap Settings list can have up to 6 monitoring systems.
Configuring Trap Settings 57
Figure 21. Trap settings
Model 1195 Getting Started Guide 6 • GUI configuration
Configuring Default Settings
To restore the default settings, click on Set Default at the top of the screen. A window will display. Click Yes
to begin the process.
The default settings are:
1. Laser Mode 3
2.
3.
E1 Local Loop
E1 Remote Loop 0
For Ethernet Port:
1. AN 1
2. Flow 1
3. Rate 1
4. Duplex 1
Figure 22. Default settings
0
Configuring Default Settings 58
Model 1195 Getting Started Guide 6 • GUI configuration
SNMP Community
To set and view the SNMP Set and SNMP Get Community options, click on SNMP at the top of the screen
and select SNMP Community. A window will display.
Figure 23. SNMP Community
Note You cannot set or view other SNMP features through the GUI.
SNMP Community 59
Model 1195 Getting Started Guide 6 • GUI configuration
Viewing Settings
To view general system settings, click on Show Settings at the top of the screen . A window will display that
shows current system values. Click on any of the properties displayed in the list and the details will be displayed
in the Result window.
Figure 24. Show settings
Viewing Settings 60
Model 1195 Getting Started Guide 6 • GUI configuration
Back Up
To create a backup of all of the settings, click on File at the top of the screen and select Back Up. A screen will
display. Click Open and select the path where you want to save the backup file. Click Save.
Figure 25. Back up
Restore
To restore settings from the backup file, click on File at the top of the screen and select Restore. A screen will
display. Click Open File. A dialog box will appear where you should select the backup file. Click Submit to
start the restore process..
Back Up 61
Figure 26. Restore
Model 1195 Getting Started Guide 6 • GUI configuration
Synchronize
To synchronize the system, click on File at the top of the screen and select Synchronize. A screen will display.
Click Yes to start the process. The purpose of synchronization is to update the database with the current set-
tings in the system. (For example, if you make any changes to system settings through the CLI).
Figure 27. Synchronize
Report
List of systems
To view the report of the list of systems, click on File at the top of the screen and select Report > List of Systems. A screen will display. Click on Generate Report. The report will display in a window.
Synchronize 62
Figure 28. View systems report
Model 1195 Getting Started Guide 6 • GUI configuration
List of traps
To view the report of the list of traps, click on File at the top of the screen and select Report > List of Traps. A
screen will display. To view the traps of a specific system, click on Traps of Selected System. To view traps of all
the systems, click on Traps of All Systems. The report will display in a window.
Report 63
Figure 29. View traps
Model 1195 Getting Started Guide 6 • GUI configuration
Read Me
To learn about system requirements for running the GUI, click on Help at the top of the screen and select
Read Me. The instructions will display in a window.
Figure 30. Readme file
Read Me 64
Model 1195 Getting Started Guide 6 • GUI configuration
System Information
To learn about firmware and GUI release versions, click on Help at the top of the screen and select About. A
window will display with the system information.
Figure 31. View system information
Exiting the System
To disconnect from the system, click on File at the top of the screen and select Exit.
System Information 65
Chapter 7 Contacting Patton for assistance
Chapter contents
Introduction..........................................................................................................................................................67
Contact information..............................................................................................................................................67
Patton support headquarters in the USA .........................................................................................................67
Alternate Patton support for Europe, Middle East, and Africa (EMEA) ..........................................................67
Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................67
Warranty coverage ..........................................................................................................................................67
Out-of-warranty service .............................................................................................................................68
Returns for credit ......................................................................................................................................68
Return for credit policy .............................................................................................................................68
RMA numbers ................................................................................................................................................68
Shipping instructions ................................................................................................................................68
66
Model 1195 Getting Started Guide 7 • Contacting Patton for assistance
Introduction
This chapter contains the following information:
• “Contact information”—describes how to contact Patton technical support for assistance.
• “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the
warranty and obtaining a return merchandise authorization (RMA).
Contact information
Patton Electronics offers a wide array of free technical services. If you have questions about any of our other
products we recommend you begin your search for answers by using our technical knowledge base. Here, we
have gathered together many of the more commonly asked questions and compiled them into a searchable
database to help you quickly solve your problems.
Patton support headquarters in the USA
• Online support: available at www.patton.com
• E-mail support: e-mail sent to support@patton.com will be answered within 1 business day
• Telephone support: standard telephone support is available five days a week—from 8:00 am to
5:00 pm EST (1300 to 2200 UTC/GMT)—by calling +1 (301) 975-1007
• Fax: +1 (253) 663-5693
Alternate Patton support for Europe, Middle East, and Africa (EMEA)
• Online support: available at www.patton-inalp.com
• E-mail support: e-mail sent to support@patton-inalp.com will be answered within 1 business day
• Telephone support: standard telephone support is available five days a week—from 8:00 am to
5:00 pm CET (0900 to 1800 UTC/GMT)—by calling +41 (0)31 985 25 55
• Fax: +41 (0)31 985 25 26
Warranty Service and Returned Merchandise Authorizations (RMAs)
Patton Electronics is an ISO-9001 certified manufacturer and our products are carefully tested before shipment. All of our products are backed by a comprehensive warranty program.
Note If you purchased your equipment from a Patton Electronics reseller, ask your
reseller how you should proceed with warranty service. It is often more convenient for you to work with your local reseller to obtain a replacement.
Patton services our products no matter how you acquired them.
Warranty coverage
Our products are under warranty to be free from defects, and we will, at our option, repair or replace the product should it fail within one year from the first date of shipment. Our warranty is limited to defects in workmanship or materials, and does not cover customer damage, lightning or power surge damage, abuse, or
unauthorized modification.
Introduction 67
Model 1195 Getting Started Guide 7 • Contacting Patton for assistance
Out-of-warranty service
Patton services what we sell, no matter how you acquired it, including malfunctioning products that are no
longer under warranty. Our products have a flat fee for repairs. Units damaged by lightning or other catastrophes may require replacement.
Returns for credit
Customer satisfaction is important to us, therefore any product may be returned with authorization within 30
days from the shipment date for a full credit of the purchase price. If you have ordered the wrong equipment or
you are dissatisfied in any way, please contact us to request an RMA number to accept your return. Patton is
not responsible for equipment returned without a Return Authorization.
Return for credit policy
• Less than 30 days: No Charge. Your credit will be issued upon receipt and inspection of the equipment.
• 30 to 60 days: We will add a 20% restocking charge (crediting your account with 80% of the purchase price).
• Over 60 days: Products will be accepted for repairs only.
RMA numbers
RMA numbers are required for all product returns. You can obtain an RMA by doing one of the following:
• Completing a request on the RMA Request page in the Support section at www.patton.com
• By calling +1 (301) 975-1007 and speaking to a Technical Support Engineer
• By sending an e-mail to returns@patton.com
All returned units must have the RMA number clearly visible on the outside of the shipping container. Please use
the original packing material that the device came in or pack the unit securely to avoid damage during shipping.
Shipping instructions
The RMA number should be clearly visible on the address label. Our shipping address is as follows:
Patton Electronics Company
RMA#: xxxx
7622 Rickenbacker Dr.
Gaithersburg, MD 20879-4773 USA
Patton will ship the equipment back to you in the same manner you ship it to us. Patton will pay the return
shipping costs.
Warranty Service and Returned Merchandise Authorizations (RMAs) 68
Appendix A Specifications
Chapter contents
E1 Interface ...........................................................................................................................................................70
Optical ..................................................................................................................................................................70
Optical Interface Specifications: 1310nm Single Mode..........................................................................................71
Transmitter Optical Characteristics .................................................................................................................71
Receiver Optical Characteristics ......................................................................................................................71
Optical Interface Specifications: 1550nm Single Mode..........................................................................................71
Transmitter Optical Characteristics .................................................................................................................71
Receiver Optical Characteristics ......................................................................................................................72
Safety.....................................................................................................................................................................72
Ethernet Interface..................................................................................................................................................72
Configuration, Management and Alarms...............................................................................................................72
Power Supply ........................................................................................................................................................72
Environment .........................................................................................................................................................73
Physical .................................................................................................................................................................73
69
Model 1195 Getting Started Guide A • Specifications
E1 Interface
• Electrical Interface: E1
• Channel capacity: Up to 8E1
• Bit rate: 2.048 Mbps + 50 ppm
• Line code: HDB3
• Frame Structure: As per G.704
• Electrical Interface: As per G.703
• Nominal impedance: 120 Ω balanced / 75 Ω unbalanced (optional)
• Jitter character: ITU-T G.742, G.823 compliant
• Connectors: Male DB37 interface with RJ-45 connectors (120 Ω balanced) or Male DB37 interface with
BNC coaxial connectors (75 Ω unbalanced)
Optical
• Type of Transmitter: Class 1 Laser
• Transmitter power: >- 3dBm, >- 6dBm, >- 9dBm options, as ordered
• Bit rate: 155 Mbps
• Wavelength: 1310/1550nm (optional)
• Optical connector: FC/PC
• Receiver Sensitivity: < - 36 dBm
• Typical output power: > -9dBm
• Fully Compliant with ITU-T G.957, G.958 Specification
• Class 1 Laser Product, Compliant with IEC 60825-1
• Compliant with Telcordia (Bellcore) GR-468-CORE
E1 Interface 70
Model 1195 Getting Started Guide A • Specifications
Optical Interface Specifications: 1310nm Single Mode
Transmitter Optical Characteristics
FC
Receiver Optical Characteristics
FC
Optical Interface Specifications: 1550nm Single Mode
Transmitter Optical Characteristics
FC
Optical Interface Specifications: 1310nm Single Mode 71
Model 1195 Getting Started Guide A • Specifications
Receiver Optical Characteristics
FC
Safety
• Class 1 Laser
• Auto Laser Shut Down in the event of fiber break.
Ethernet Interface
• 10/100BaseT
• Number of Interfaces: 1
• Interface: RJ-45 Ethernet 10BaseT or 100BaseT-TX (auto sensing)
• Compliance: Ethernet Version 2.0 IEEE802.3
• 10Base-T & 100Base-TX Activity, Full/half duplex.
• Interface Rate: 100 Mbps Ethernet data transmission rate
• Connector: RJ-45
Configuration, Management and Alarms
• Serial Management Port - RS232 interface
• 10/100 BaseT for Remote Management over a LAN
• 10/100 BaseT Telnet over a TCP-IP Network
• SNMP V2
Power Supply
• Power Input: AC, DC, AC + DC
• DC power:DC - 48V(-36~-72V)
• AC power:AC 220V (185~265V)
• Power consumption: 18 Watts maximum
Safety 72
Model 1195 Getting Started Guide A • Specifications
Environment
• Temperature: -5ºC ~ +55ºC for operation
• - 40ºC to +70ºC for storage
• Humidity: 5% to 95% (35ºC) - non-condensing
Physical
• Width: 1552 mm
• Depth: 434 mm
• Height: 44 mm
• Weight: 2 kg.
• Rack Type: EIA 19-Inch
Environment 73
Appendix B Connector pinouts
Chapter contents
DB-37 connector pinout (Model 1195).................................................................................................................75
DB-37 connector pinout details for E1 connections ........................................................................................75
74
Model 1195 Getting Started Guide B • Connector pinouts
DB-37 connector pinout (Model 1195)
Figure 32. DB-37 connector pinout
DB-37 connector pinout details for E1 connections
DB-37 connector pinout (Model 1195) 75
Model 1195 Getting Started Guide B • Connector pinouts
DB-37 connector pinout
Figure 33. DB-37 connector pinout
DB-37 connector pinout details for E1 connections
DB-37 connector pinout (Model 1195)
76
Loading...