USER
MANUAL
MODEL 1089 C and D
HDSL Modem with
V.35 or X.21 Interface
Part# 07M1089-UM
Doc# 03208U2-001
Rev. C
Revised 10/24/06
SALES OFFICE
(301)975-1000
TECHNICAL SUPPORT
(301)975-1007
http://www.patton.com
An ISO-9001
Certified
Company
CERTIFIED
CERTIFIED
TTAABBLLEE OOFF CCOONNTT EE NNTTSS
Section Page
1.0 Warranty Information.............................................................2
1.1 Radio and TV Interference
1.2 CE Notice
1.3 Service
2.0 General Information...............................................................4
2.1 Features
2.2 Description
3.0 Configuration .........................................................................5
3.1 Configuring the Hardware DIP Switches
3.1.1 Configuration DIP Switch Set “S2”
3.1.2 Configuration DIP Switch Set “S3”
4.0 Installation ...........................................................................10
4.1 Connecting the Twisted Pair Interface
4.2 Connecting the Model 1089/C (V.35) Serial Interface
4.2.1 Connecting the Model 1089/C to a DTE Device
4.2.2 Connecting the Model 1089/C to a DCE Device
4.3 Connecting the Model 1089/D (X.21) Serial Interface
4.3.1 Connecting the Model 1089/D to a DCE or DTE
Device
4.3.2 Opening the Case
4.4 Connecting Power
4.4.1 Universal Power (100 - 240VAC)
4.4.2 120VAC Power (US)
4.4.3 230VAC Power (International)
4.4.4 48VDC Power
5.0 Operation.............................................................................15
5.1 Power-Up
5.2 LED Status Monitors
5.2.1 LED Descriptions Chart
5.3 Test Modes
5.3.1 Overview
5.3.2 Loops and Patterns
5.3.3 Using the V.52 (BER) Test Pattern Generator
Appendix A - Specifications ........................................................26
Appendix B - Factory Replacement Parts and Accessories.......27
Appendix C & D - Interface Pin Assignments.............................28
Appendix E - Transmission Distance Chart................................30
1
11..00 WWAARRRR AANNTT YY IINNFFOORR MMAA TT IIOONN
Patton Electronics warrants all Model 1089 components to be
free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials,
and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product.
Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall
be deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 1089 generates and uses radio frequency energy, and
if not installed and used properly—that is, in strict accordance with the
manufacturer's instructions—may cause interference to radio and television reception. The Model 1089 has been tested and found to comply with the limits for a Class A computing device in accordance with
the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the Model 1089 does
cause interference to radio or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the
receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are
on different branches).
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the European Union
(EU). A Certificate of Compliance is available by contacting Technical
Support.
2
1.3 SERVICE
All warranty and non-warranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Service at:
tel: (301)975-1007
email: support@patton.com
www: http://www.patton.com
Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Model 1089. Technical Service hours: 8AM to 5PM EST, Monday
through Friday.
3
22..00 GGEENNEERRAALL IINNFFOORRMMAATTIIOONN
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is warranted for One Year parts and labor. If any questions or problems arise
during installation or use of this product, please do not hesitate to contact Patton Electronics Technical Support at (301) 975-1007.
2.1 FEATURES
• High Bit-Rate DSL
• 2B1Q Modulation
• DTE Rates up to 1.154Mbps
• V.35 and X.21 Interfaces
• Interoperable with Popular Model 1094A
• SNMP Manageable via 1001MC SNMP Agent Rack Card through
1094RC/CO
• Universal Power Options, 120VAC, 230VAC and -48VDC Available
• Front Panel Status Indicators
• Small, Convienent Desktop Unit
• CE Marked
2.2 DESCRIPTION
The Patton Electronics HDSL Rocket provides high speed 2-
wire connectivity to ISPs, PTTs, and corporations using HDSL (Multirate Symmetric Digital Subscriber Line) technology. Supporting multiple line rates from 144kbps to 1.168Mbps, the NetLink provides
“megabyte” speeds to leased line, LAN to LAN interconnection, and
WAN access networks over 3.6 miles/5.8km (1.054Mbps on
24AWG/.5mm wire).
Model 1089/C provides a V.35 interface on an M/34 female con-
nector. Model 1089/D provides an X.21 interface on a DB-15 female
connector. Features include loopback diagnostics, inband
SNMP/HTTP remote management capabilities through 1094RC/CO
and externally accessible configuration switches. All versions of the
Rocket are compatible with Patton’s popular Model 1094A standalone
and 1094ARC rack card.
As a symmetric DSL NTU, NetLink
TM
mDSL offers the same data
rates in both directions over a single pair of regular telephone lines
using 2B1Q modulation. Line connection is made by an RJ-45 jack.
Standard versions of Model 1089 are powered by a
100/230VAC(Universal) supply. The DC power supply option supports
any DC input between 36-72VDC.
4
IMPORTANT: The Model 1089 is equipped with flash
upgrade. Please refer to Patton website, or contact Technical
Support for the latest version of the software.
NOTE: Packages received without an RMA number will not be
accepted.
33..00 CCOONNFF IIGGUURR AATTIIOONN
The Model 1089 is equipped with two sets of eight DIP switches,
which allow configuration of the unit for a wide variety of applications.
This section describes switch locations and explains all possible configurations.
3.1 CONFIGURING THE HARDWARE DIP SWITCHES
The 16 external switches are grouped into two eight-switch sets,
and are externally accessible from the underside of the Model 1089
(See Figure 1).
The two sets of DIP switches on the underside of the Model 1089
will be referred to as S2 and S3. As Figure 2 shows, the orientation of
all DIP switches is the same with respect to “ON” and “OFF” positions.
5
Figure 2. Close Up of Configuration Switches (all sets are identical in appearance)
Figure 1. Underside of Model 1089, Showing Location of DIP Switches
Front
Back
On
S2
S3
Off
3.1.1 Configuration DIP Switch Set “S2”
The configuration switches on S2 allow you to specify the Clocking
Mode and to enable/disable Local and Remote Loop requests from the
V.35 DTE. Default settings of S2 are shown in the table below.
Switch S2-1, S2-2, S2-3, S2-4, and S-5:
Reserved for factory use and must remain in the OFF position.
Switches S2-6 and S2-7: Clock Mode
Use Switches S2-6 and S2-7 to configure the 1089 for internal,
external, or receive recover clock mode.
6
Position Function
S2-1 Reserved
S2-2 Reserved
S2-3 Reserved
S2-4 Reserved
S2-5 Reserved
S2-6 Clock Mode On
S2-7 Clock Mode Off
S2-8 Enable Loop from DTE
S2 SUMMARY TABLE
Factory Default
Off
Off
Off
Off Disabled
Off
On
Receive
Recover
OFF
ON
CO/CP
Unit S2-6 S2-7 Clock Mode Description
CO On On Internal Transmit clock
generated internally
CO Off On External (DTE) Transmit clock
derived from
terminal interface
CP On Off Receive Recover Transmit clock
derived from the
received line
Off Off
Reserved
7
Switch S2-8: Enable/Disable Loop Tests from DTE
Switch S2-8 may be used to allow Model 1089/C to enter loopback
diagnostic tests (Local or Remote) when the V.35 DTE raises the
appropriate loop request pin (LLB: Pin L or RDL: Pin N). When Switch
S2-8 is in the On position, the Model 1089/C will enter Local Loopback
or Remote Loopback at the request of the DTE. When Switch S2-8 is
in the Off position, the Model 1089/C ignores DTE loop requests. In
the Off position, loop requests may still be initiated by the front panel
switch.
S2-8 Setting
On DTE Loopback Request Enabled
Off DTE Loopback Request Disabled
3.1.2 Configuration Switch Set “S3”
Use the eight DIP Switches in Switch S3 to enable the DTE bit
rate. The following table summarizes default positions of DIP Switch
S3. Detailed descriptions of each switch follow the table.
Switch S3-1: DTE Rate
Use Switch S3-1 through S3-6 to set the DTE bit rate.
S3-1 S3-2 S3-3 S3-4 S3-5 S3-6 DTE Rate (kbps)
Off Off On On On On 64
On On Off On On On 128
Off On Off On On On 192
On Off Off On On On 256
Off Off Off On On On 320
On On On Off On On 384
Off On On Off On On 448
On Off On Off On On 512
Off Off On Off On On 576
On On Off Off On On 640
Off On Off Off On On 704
On Off Off Off On On 768
Off Off Off Off On On 832
On On On On Off On 896
Off On On On Off On 960
On Off On On Off On 1024
Off Off On On Off On 1088
On On Off On Off On 1152
8
S3 SUMMARY TABLE
Position Function Factory Default
S3-1 DTE Rate On
S3-2 DTE Rate Off
S3-3 DTE Rate Off
S3-4 DTE Rate Off
S3-5 DTE Rate On
S3-6 DTE Rate On
S3-7 Reset Software Defaults On
Normal Operation
S3-8
Transmit Data Sample Point
On Normal Operation
}
768 kbps
9
Switch S3-7: Reset Software Defaults
Switch S3-7 allows the user to reset the software configured factory
defaults. This will only be needed when using the Model 1001MC to
SNMP manage your units. For more information, please refer to the
Model 1001MC Operations Manual.
S3-7 Setting
On Normal Operation
Off Reset
Switch S3-8: Transmit Data (TD) Sampling Point
Switch 3-8 controls the Transmit Data (TD) sampling point.
S3-8 Setting Description
On Normal TD sampled on the falling
edge of the 1089 Transmit
Clock (TC)
Off Invert TD sampled on the rising
edge of the 1089 Transmit
Clock.
10
44..00 IINNSS TT AALLLLAATTIIOONN
Once the Model 1089 is properly configured, it is ready to connect
to the twisted pair interface, to the serial port, and to the power source.
This section tells you how to make these connections.
4.1 CONNECTING THE TWISTED PAIR INTERFACE
The Model 1089 supports communication between two DTE
devices at distances to 5 miles (8 km) over 24 AWG (.5mm) twisted
pair wire. Two things are essential:
1. These units work in pairs. Both units at the end of the twisted
pair DSL span must be set for the same DTE rate.
2. To function properly, the Model 1089 needs one
twisted pair of metallic wire. This twisted pair must be
unconditioned, dry, metallic wire, between 19 (.9mm) and 26
AWG (.4mm) (the higher number gauges will limit distance).
Standard dial-up telephone circuits, or leased circuits that run
through signal equalization equipment, or standard, flat modular telephone type cable, are
not acceptable.
The RJ-45 connector on the Model 1089’s twisted pair interface is
polarity insensitive and is wired for a two-wire interface. The signal/pin
relationships are shown in Figure 3 below.
NOTE: Based on the DTE rate chosen, the Model 1089 will
automatically select the optimum line rate depending on distance and line conditionsfor the distance. The line selection will
be based on the lowest line rate that will support the DTE rate.
Figure 3. Model 1089 RJ-45 twisted pair line interface.
1 (N/C)
2 (N/C)
3 (N/C)
4 (2-Wire TIP)
5 (2-Wire RING)
6 (N/C)
7 (N/C)
8 (N/C)
1
2
3
4
5
6
7
8
IMPORTANT!: The Model 1089 has been optimized for per-
formance at high bitrates (DTE rates greater than 512 kbps). To
ensure accurate performance at these bit rates, please use twisted pair line interface cable that is at least 330ft (100m) in length.
11
4.2 CONNECTING THE MODEL 1089/C (V.35) SERIAL INTERFACE
Model 1089/C supports V.35 serial port connections. This section
describes how to connect the serial ports to your V.35 equipment.
4.2.1 Connecting the Model 1089/C (V.35) to a “DTE” Device
The Model 1089/C provides a V.35 DCE (Data Circuit Terminating
Equipment) interface on an M/34 female connector. As a DCE, this
interface is designed to connect to DTE equipment, such as a router.
When connecting the V.35 interface of the Model 1089/C to your DTE
device, use a V.35 straight through cable (See Figure 4, below).
Appendix C describes pin assignments and signal sources for the
Model 1089/C V.35 interface. When purchasing or constructing an
interface cable, please refer to the pin diagrams in Appendix C as a
guide.
4.2.2 Connecting the Model 1089/C (V.35) to a “DCE” Device
The Model 1089/C provides a V.35 (Data Circuit Terminating
Equipment) interface on an M/35 female connector. As a DCE, this
interface is designed to connect to DTE equipment, such as a router.
However, tail-circuit applications require connection to another DCE
equipment, such as a multiplexer. When connecting the V.35 interface
of the Model 1089/C to your DCE device, use a V.35 null modem
cable. Some applications may also required the installation of a V.35
tail-circuit buffer to account for small differences in clock frequency
between the 1089/C and the V.35 DCE (multiplexer).
4.3 CONNECTING THE MODEL 1089/D (X.21) SERIAL INTERFACE
Model 1089/D supports X.21 serial port connections. This section
describes how to connect the serial ports to your X.21 equipment.
4.3.1 Connecting the Model 1089/D (X.21) to a “DCE” or “DTE”
Device
The Model 1089/D provides an X.21 interface on a DB-15 female
connector. The X.21 interface default configuration is DCE (Data
Circuit Terminating Equipment) for connection to DTE (Data Terminal
Equipment) such as a router. However, the X.21 interface on the
Model 1089/D may be configured as DTE (Data Terminal Equipment)
for connection to DCE such as a modem or multiplexer. When connecting the X.21 interface of the Model 1089/C to your DTE device,
use a X.21 straight through cable (See Figure 6, below).
To modify the DCE/DTE orientation from the default position
(DCE), you must open the Model 1089/D case.
4.3.1 Opening the Case
To open the Model 1089/D case, insert a flat head screw driver
into an open slot on both sides of the case, as in Figure 7. Twist the
screw driver head slightly and the top half of the case will separate
from the lower half, as in Figure 7, below. Take caution not to damage of the pc-board mounted components.
12
Figure 4. Connecting the Model 1089/C to V.35 Serial DTE
Figure 5. Connecting the Model 1089/C to V.35 Serial DCE
Straight-Through M/34
Cable
DSL Span
Model 1089/C (DCE)
Remote Model 1089)
Router (DTE) with V.35
Serial Interface
Figure 6. Connecting the Model 1089/D to X.21 DTE or DCE
Straight-Through 15-pin
D-Sub Cable
DSL Span
Router (DTE)
OR
Mux (DCE)
Model 1089/D (DCE or DTE)
Remote Model 1089)
Figure 7. Opening the 1089 Case with a Small Screwdriver
DSL Span
Remote Model 1089
Model 1089/C (DCE)
V.35 Multiplexer (DCE)
The DCE/DTE strap is located on the top side of the 1089/D pc
board (See Figure 8, below). The arrows on the top of the strap indicate the configuration of the X.21 port (for example, if the DCE arrows
are pointing toward the DB-15 connector, the X.21 port is wired as a
DCE). Change the DCE/DTE orientation by pulling the strap out of its
socket, rotating it 180º, then plugging the strap back into the socket.
You will see that the DCE/DTE arrows now point in the opposite directions, showing the new configuration of the X.21 port.
To close the
case, fit the 2 halves together snugly and snap them back in place.
4.4 CONNECTING POWER
The Model 1089 (all versions) are available with Universal AC
(100-240VAC), 120VAC, 230VAC or -48VDC power options. This section describes these options.
4.4.1 Universal AC Power (100-240VAC)
The Model 1089 uses a 5VDC, 2A universal input 100-240VAC,
power supply (center pin is +5V). The universal input power supply
has a male IEC-320 power entry connector. This power supply connects to the Model 1089 by means of a barrel jack on the rear panel.
Many international power cords are available for the universal power
supply (Please refer to Appendix B for country-specific power cords.
The Model 1089 powers up as soon as it is plugged into an AC
outlet--there is no power switch.
13
4.4.2 120 VAC Power (US)
The 100-132 VAC adapter supplied with the U.S. version of the
Model 1089 is a wall mount type and may be plugged into any
approved 120 VAC wall jack.
4.4.3 230 VAC Power (International)
The 230 VAC adapter supplied with the International version of the
Model 1089 is a wall mount type and may be plugged into any
approved 230 VAC wall jack.
4.4.4 DC Power
The 36-60 VDC DC to DC adapter is supplied with the DC version
of the Model 1089. The black and red leads plug into a DC source
(nominal 48VDC) and the barrel power connector plugs into the barrel
power supply jack on the rear panel of the 1089. (See Figure 9).
14
DCE/DTE Strap
DB-15 Connector
Figure 8. Setting the DCE/DTE Strap
Figure 9. Connecting DC Power to the 48V-PSM DC Power Supply.
WARNING! There are no user-serviceable parts in the
power supply section of the Model 1089. Fuse replacement
should only be performed by qualified service personnel.
Contact Patton Electronics Technical support at
(301)975-
1007
, via our web site at http://www.patton.com, or by e-mail
at support@patton.com, for more information.
To Power
Supply Jack
S/N: G01234567890
MADE IN CHINA BY SUNNY
Barrel power connector
MODEL : SYD1106-0505
INPUT : 36-60V 0.2A MAX
OUTPUT : +5V 1.0A
OUTPUT POWER : 5W MAX
SWITCHING POWER SUPPLY
-Vin
+Vin
To -48VDC
Source
Black lead (-V)
Red lead (+V)
55 .. 00 OO PP EE RRAATTII OONN
Once the Model 1089 is properly configured and installed, it
should operate transparently. This sections describes power-up, reading the LED status monitors, and using the built-in loopback test
modes.
5.1 POWER-UP
To apply power to the Model 1089, first be sure that you have
read Section 4.4. The unit powers up when it is plugged into the
power source.
5.2 LED STATUS MONITORS
The Model 1089 features six front panel LEDs that monitor
power, the DTE signals, network connection and test modes. Figure
10 (below) shows the front panel location of each LED. Following
Figure 10 is a description of each LEDs function. See also, section
5.2.1 Model 1089 LED Descriptions Chart
DSL Link (Active Green) Solid green (On) indicates that the
end to end DSL Framer Link is up, signifying that
the link across the DSL span is active. The DSL
Link LED is Off when the link is down.
TD & RD Glows yellow to indicate an idle condition of Binary
“1” data on the respective terminal interface signals. Green indicates Binary “0” data
NS (No Signal) glows red to indicate that the local
Model 1089 is not connected with the remote
Model 1089.
ER- blinks ON/OFF after a 511/511E test has timed out. See
Section 5.3.3 (Test Pattern Generator) for more
information.
- flashes once to indicate that a CRC error has
occurred (during normal operation) or bit errors
have occurred (during 511/511E tests).
15
- Only at power up, blinks once every 200 ms if
the DTE Rate is set to an unsupported settings
TM glows yellow to indicate that the Model 1095
has been placed in Test Mode. The unit can be
placed in test mode by the local user or by the
remote user. The TM LED will flash for 400msec
when a valid packet is received from the Model
1001MC.
5.3 TEST MODES
The Model 1089 offers two proprietary loopback test modes, plus
a built-in V.52 BER test pattern generator to evaluate the condition of
the modems and the communication link. These tests can be activated physically from the front panel or via the DTE interface.
5.3.1 Overview
Figure 11 shows the major elements used in the loop-back and
pattern tests available in the Model 1089. Each block has several functions. Following Figure 11 are descriptions that show how the elements
are used during Test Modes.
16
Figure 10. Model 1089 Front Panel
Clock (CO) Internal 768Kb No DTE Clock (CP) R/R No DTE
TD RD DSL NS ER TM TD RD DSL NS ER TM
Power ON G O off ON off off O O off ON off off
DSL Link G O G off off off O G G off off off
Link Brk G O off off off off O O off off off off
Brk+ 10s G G off ON off off O O off ON off off
RDL G G G off off ON O G G off off ON
RDL+511 G G off off off ON O G off off off ON
With DTE Connected With DTE Connected
Mark O O G off off off O O G off off off
Space G G G off off off G G G off off off
Data GO GO G off off off GO GO G off off off
Link Brk = DSL Link Broken
Brk+10s = 10 Seconds following Link Break
G=GREEN
O=ORANGE
ON= ON
off= OFF
Y=yellow
5.2.1 Model 1089 LED Descriptions Chart
NetLink X.21 HDSL Rocket
DSL
Link
TD
NS TMRD ER
Local -
Normal -
Remote -
- 511E
- Normal
- 511
Figure 11: Block Diagram Model 1089
Framer The framer is used to determine the status of
the line. In normal operation the framer transmits and expects to receive framed packets
from the far end. If the framer receives framed
packets from the far end, CTS and CD will be
active. If framed packets are not received, CTS
and CD will be inactive. The restart procedure
uses this information to determine if a valid connection is made (cable disconnect, poor cable
quality, etc). In normal Data Mode, if the Model
1089 receives 4 seconds of unframed packets it
will restart and begin trying to re-establish a
connection with the far end. The distinction
between framed packets and unframed packets
becomes important when we discuss the Pattern
Generator.
Pattern Gen/Det This part of the Processor generates and
detects the 511/511E patterns. When transmitting 511 patterns, the information is unframed
(because it originates after the framer) and is
intended to be evaluated only by another
Processor. If the units are in Data Mode and the
pattern generator is enabled on one end of the
link, the far end will begin receiving unframed
packets and assume that the line has gone
down. During test modes, we force the pattern
generator to time out before it can cause the link
to be killed.
Loop Control This part of the Processor is used to control
loop-backs. In a Local Loop, the data is looped
back towards the local DTE. In a Remote Loop,
the data is looped back to the line, but it is also
allowed to pass through to the framer and to the
remote DTE.
17
Restart Procedure The restart procedure is in place to allow the
and Time Outs units to re-establish a connection after the
framer begins seeing unframed packets. The
Test Model Timing Chart below shows the
amount of time the framer must see consecutive
unframed packets before the unit will restart and
try to establish a new line connection. The reason that there are different Restart Times will
become apparent after reading the rest of the
document. The 511/511E Time Out shown refers
to the amount of time the 511/511E pattern will
be valid. At the end of this time the pattern will
automatically turn itself off and the normal data
path will be re-established. The ER led will flash
indicating to the user that the test has timed out.
The ER led will stop flashing once the 511/511E
switch is placed into the normal position.
Symbol Indicators
This symbol designates the origination or the
termination of a data path. The direction of the
arrow connected distinguish the two data paths.
This symbol designates an invalid data path. If
there is data present it should be ignored.
18
Test Mode Timing
Item Elapsed Time (seconds)
Start Up 50
Data Mode 4
511/511E Generator Enabled 60 (The generator will stop after 45 seconds.)
Remote End of an RDL 60
511/511E Time Out 45 (The pattern generator will automatically turn
off after 45 seconds. The ER LED will flash until
the user turns off the 511/511E switch.)
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
5.3.2 Loops and Patterns
The following section describes the Test Modes used in the Model
1089. At the bottom of each Test Mode, a figure is included to show
the data path.
Local Loop There are two different modes of operation for a
Local Loop depending on the status of the units
at the time that the Local Loop is initiated. If the
units are not in linked (NS LED on) and the
Local Loop is initiated, either by the front panel
switch or the DTE interface, the unit will enter
mode 1. If the units are linked, NS LED off, then
the unit will enter a mode 2 Local Loop.
A Mode 1 Local Loop is shown in Figure 7.
When the Local Loop is initiated, either by the
front panel switch or the DTE interface, the loop
will be activated within the local Processor. The
data present at the local DTE interface will be
looped back to the local DTE by the Loop
Control block within the Processor. Any data
present on the line or at the far end DTE interface is invalid. The remote unit will remain in the
StartUP mode, NS LED on, CTS LED yellow,
and CD LED yellow, until the local unit is taken
out of the Local Loop mode. After the Local
Loop is deselected, the units will both be in
StartUP mode and the link will be established.
A mode 2 Local Loop is shown in Figure 8.
When the Local Loop is initiated, either by the
front panel switch or the DTE interface, two separate loop paths will be started. In the first path,
data presented to the local DTE interface will be
looped back to the local DTE within the framer.
In the second path, data presented at the far
end DTE will be transmitted to the local DTE
and then looped back within the local DTE Loop
Control block with the Processor. After the Local
Loop is deselected, the units will be placed back
into DataMode and the normal data paths will be
re-established.
19
Figure 12. Block Diagram Local Loop Mode 1
Figure 13. Block Diagram Local Loop Mode 2
Local Loop When the unit is placed into a Mode 1. Local
with 511/511E Loop and the 511/511E pattern generator is acti-
vated, the local pattern generator begins sending out a 511/511E pattern to the Loop Control
block. The Loop Control block will loop this data
back to the 511/511E pattern detector block,
which will evaluate the data for errors. Because
the 511/511E pattern generator is contained
within the Processor the data is unframed so the
framer will begin seeing unframed packets. The
framer receives this unframed data and can not
distinguish this information from a line disconnection (this would cause the units' Restart procedure to start). What we have done to allow
this mode to work is to add time outs for the pattern generators. When the 511/511E is initiated,
the line restart procedure is changed to one
minute. The 511/511E pattern will timeout after
45 seconds. So if the 511/511E is turned on during a local loop, the restart procedure is set to
one minute, but the 511/511E pattern will time
out after 45 seconds, allowing the framer to
begin seeing framed packets (and not restart
the box).
20
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Pattern
Gen/Det
Loop Contr
ol
Loop Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Local Loop After the 511/511E pattern times out, the ER led
with 511/511E will begin flashing. It will remain this way until
(continued) the pattern generator switch is turned off. Note
that the data at the local DTE and the remote
DTE are not valid. Because the data is
unframed there is no way for the framer to send
this data out to the DTE. This is an important
distinction because other Patton units will send
out the 511 pattern.
When the unit is placed into a Mode 2 Local
Loop, the 511/511E pattern generator on the
local unit is unavailable for transmission. As can
be seen from Figure 11, the 511/511E pattern
generator has no data path connections available. The 511/511E pattern generator is still
available on the remote unit. For more information on the proper operation of this pattern generator please refer to the "Remote Digital Loop
with 511/511E" section.
Figure 14. Block Diagram Local Loop Mode 1 with 511/511E
Figure 15. Block Diagram Local Loop Mode 2 with 511/511E
21
Remote Digital The Remote Loop uses the EOC channel (an
Loop out-of-band signaling channel) to establish the
remote link. Upon the RDL switch being thrown
or DTE initiation, a RDL_ON Request signal is
sent to the remote unit. The Remote unit then
responds with an RDL Acknowledge command
and the link is established. Data originates at
the local DTE and is looped at the Remote
PROCESSOR back to the Local DTE. Note that
the data is also passed through to the Remote
DTE and is not squelched. When a Remote unit
enters RDL, it changes its' Restart timeout to
one minute (the reason will be explain in the
RDL with 511/511E section). If the line is disconnected, the local unit will Restart (NS led activated) after 4 - 6 seconds, but the Remote unit will
wait for one minute before it Restarts. Note that
the transmit data at the Remote DTE is ignored.
When the switch is thrown or the DTE removes
the RDL request, the local unit will transmit an
RDL_OFF Request to the Remote unit. The
local unit will keep its' TM led active until this
request has been completely sent out. If the
switch is thrown again before the completion of
the termination phase the switch will be ignored
until it is placed back into the normal position.
Figure 16. Block Diagram Remote Loop
22
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Remote Digital The Remote Digital Loop with 511/511E is
Loop with shown above. After RDL is established the
511/511E Remote units' Restart Timer is set to one
minute. This has been done because when the
511/511E generator is started on the local unit,
the Remote framer begins seeing unframed
packets. The Remote unit can not distinguish
the 511/511E pattern from the line being disconnected so the Restart Timer has been lengthened to allow the pattern generator to function.
Once the 511/511E test is started, the Local unit
changes its' Restart Timer to one minute. The
pattern originates within the Processor and is
sent to the Remote unit. It is then looped back
to the Local unit where it is evaluated for errors.
After 45 seconds, the Pattern Generator will
timeout and stops sending the pattern. The ER
led will begin blinking until the user turns off the
511/511E switch.
Figure 17. Block Remote Loop with 511/511E
23
Data Mode with When the units enter DataMode it is possible to
511/511E Pattern turn on the 511/511E pattern generators on
Generators both ends of the link. Once a 511/511E pattern
is selected on one end of the link, the pattern
generator will begin transmitting unframed
511/511E through the line to the Remote end. A
possible problem with this test can occur due to
the Restart procedure. Once the Local 511/511E
is turned on, the Remote unit begins receiving
an unframed 511 pattern. If the Remote unit
does not turn on the 511/511E-pattern generator
within 4 seconds, the Remote unit will Restart
and enter the StartUp mode. Note that once the
511/511E-pattern generator is started the
Restart timer is changed to one minute (only on
the unit which has the pattern enabled). If both
units enable the 511/511E pattern within 4 seconds of each other, both units will be transmitting and receiving the 511/511E pattern. Both
framers are now receiving unframed data and
will restart after one minute. The 511/511E pattern generators will TimeOut after 45 seconds
re-enabling the normal data path. The ER led
will begin flashing until the user terminates the
test.
Figure 18. Block Diagram DataMode with 511/511E
24
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
Pattern
Gen/Det
Loop
Contr
ol
Loop
Contro
l
Pattern
Gen/Det
Processor
Processor
Framer
Framer
Line
5.3.3 Using the V.52 (BER) Test Pattern Generator
To use the V.52 BER tests in conjunction with the Remote Digital
Loopback tests (or with Local Line Loopback tests), follow these
instructions:
1. Locate the “511/511E” toggle switch on the front panel of the
1089 and move it UP. This activates the V.52 BER test mode
and transmits a “511” test pattern into the loop. If any errors
are present, the local modem’s red “ER” LED will blink
sporadically.
2. If the above test indicates no errors are present, move the
V.52 toggle switch DOWN, activating the “511/E” test with
errors present. If the test is working properly, the local
modem's red “ER” LED will glow. A successful “511/E” test
will confirm that the link is in place, and that the Model
1095’s built-in “511” generator and detector are working
properly.
25
26
AAPPPPEENNDDII XX AA
PATTON ELECTRONICS MODEL 1089/C AND 1089/D
SPECIFICATIONS
Clocking Modes: Internal, External, or Receive Recovered
DTE Rate: All 64k steps from 64 to 2304 kbps
DTE Interface: V.35 (Model 1089/C), DCE Orientation;
X.21 (Model 1089/D), DCE or DTE
Orientation depending upon orientation of
pc-board mounted daughter board
DTE Connector: M/34 Female (Model 1089/C)
D-Sub-15 Female (Model 1089/D)
Diagnostics: V52 compliant (511/511E) pattern generator
and detector with error injection mode controlled by front panel switch, Local and
Remote Loopback control by either a front
panel switch or from the DTE interface
LED Status: The following LEDs are displayed on the
front panel:
DSL Link (Green Active) - DSL Link Active
TD, RD (Yellow/Green) - Idle Yellow
NS (Red Active) - No signal DSL Link
ER (Flashing Red) - CRC error during nor-
mal operation, bit error during pattern generation test
TM (Active Yellow) - Test Mode Enabled
Configuration: Externally accessible dip switches or SNMP
managed through 1095RC
Power: +5V External desk top power supply, 90-
260VAC, 50-60 Hz (Universal Input), 10W
or -48VDC
Compliance: FCC Part 15, CE
Transmission Line: Single Twisted Pair
Line Coding: 2B1Q
Line Rates (DSL line): 144, 272, 400, 528, 784, 1040, 1168kbps
Line Interface: Transformer coupled, 1500 VAC isolation
mDSL Physical
Connection:
RJ-45, 2 wire, polarity insensitive pins 4
and 5
Environment: Operating temperature 0-50°C; humidity 5-
95% non-condensing; altitude, 0-15, 000
feet (0-4600 m)
NOTE: The above V.52 BER tests can be used independently
of the Remote Digital Loopback tests. This requires two operators: (1) to initiate and monitor the tests at the local Model 1089,
and (2) to do the same at the remote Model 1089. In this case,
the test pattern sent by each Model 1089 will not be looped back,
but will be transmitted down the line to the other Model 1089.
While one operator initiates test, the other monitors for errors.
AAPPPPEENNDDII XX BB
PATTON ELECTRONICS MODEL 1089/C AND 1089/D
FACTORY REPLACEMENT PARTS
AND ACCESSORIES
Patton Electronics Model # Description
1089/C.............................V.35 mDSL Rocket (CAP)
1089/D.............................X.21 mDSL Rocket (CAP)
080551 ............................120V Power Supply
080552 ............................230V Power Supply
48V-PSM.........................DC Power Supply Module
08055DCUI .....................100-240VAC (+5V ±5% reg. DC/2A)
Universal Input Adapter
0805EUR ........................European Power Cord CEE 7 (“A”)
0805UK ...........................United Kingdom Power Cord (“D”)
0805US ...........................American Power Cord (“K”)
0805AUS.........................Australia/New Zealand Power Cord (“C”)
0805DEN.........................Denmark Power Cord (“E”)
0805FR............................France/Belgium Power Cord (“F”)
0805IN.............................India Power Cord (“G”)
0805IS.............................Israel Power Cord (“H”)
0805JAP..........................Japan Power Cord (“J”)
0805SW...........................Switzerland Power Cord (“L”)
07M1089/C......................User Manual
AAPPPPEENNDDII XX CC
PATTON ELECTRONICS MODEL 1089/C
INTERFACE PIN ASSIGNMENTS
V.35 INTERFACE
(M/34 Female Connector)
(DCE Orientation)
Pin # Signal
B ...........................SGND (Signal Ground)
C ...........................RTS (Request to Send) (DTE Source)
D ...........................CTS (Clear to Send) (DCE Source)
E ...........................DSR (Data Set Ready) (DCE Source)
F............................CD (Carrier Detect) (DCE Source)
H ...........................DTR (Data Terminal Ready) (DTE Source)
L............................LLB (Local Line Loop) (DTE Source)
M ...........................TM (Test Mode) (DTE Source)
N ...........................RDL (Remote Digital Loop) (DTE Source)
P ...........................TD (Transmit Data) (DTE Source)
R ...........................RD (Receive Data) (DCE Source)
S ...........................TD/ (Transmit Data-B) (DTE Source)
T............................RD/ (Receive Data-B) (DCE Source)
U ...........................XTC (External Transmit Clock) (DTE Source)
V ...........................RC(Receiver Clock) (DCE Source)
W...........................XTC/ (External Transmit Clock) (DTE Source)
X ...........................RC/ (Receiver Clock) (DCE Source)
Y ...........................TC (Transmitter Clock-A) (DCE Source)
AA ..........................TC/ (Transmit Clock-B) (DCE Source)
27 28
AAPPPPEENNDDII XX DD
PATTON ELECTRONICS MODEL 1089/D
INTERFACE PIN ASSIGNMENTS
X.21 Interface
(D-Sub-15 Female Connector)
(DTE /DCE Orientation)
Pin # Signal
1 ......................Frame Ground
2 ......................T (Transmit Data-A) (DTE Source)
3 ......................C (Control-A) (DTE Source)
4 ......................R (Receive Data-A) (DCE Source)
5 ......................I (Indication-A) (DCE Source)
6 ......................S (Signal Element Timing-A) (DCE Source)
7 ......................BT (Byte Timing-A) (DCE Source)
8 ......................SGND (Signal Ground)
9 ......................T/ (Transmit Data-B) (DTE Source)
10......................C/ (Control-B) (DTE Source)
11......................R/ (Receive Data-B) (DCE Source)
12......................I/ (Indication-B) (DCE Source)
13......................S/ (Signal Element Timing-B) (DCE Source)
14......................BT/ (Byte Timing-B) (DCE Source)
AAPPPPEENNDDII XX EE
PATTON ELECTRONICS MODEL 1089/C AND 1089/D
TRANSMISSION DISTANCES
29 30
Line Rate DTE Rates
kbps feet miles km feet miles km
144 64, 128 20700 3.9 6.2 24500 4.6 7.3
272 192, 256 17400 3.3 5.2 24200 4.5 7.2
400 320, 384 15100 2.9 4.6 22600 4.2 6.7
528 448, 512 14900 2.8 4.4 21000 3.9 6.2
784 576, 640, 704, 76813500 2.6 4.2 18000 3.4 5.4
1040 832, 896, 960, 102411900 2.3 3.6 15500 2.9 4.6
1168 1088 - 1152 11000 2.1 3.3 15200 2.8 4.4
Line Rate DTE Rates
kbps feet miles km feet miles km
144 64, 128 18600 3.5 5.6 22100 4.2 6.7
272 192, 256 15700 2.9 4.6 21800 4.1 6.5
400 320, 384 12800 2.4 3.8 19200 3.6 5.7
528 448, 512 13000 2.5 4 18300 3.4 5.4
784 576, 640, 704, 76812200 2.3 3.6 16200 3.1 4.9
1040 832, 896, 960, 102410500 1.9 3 13600 2.5 4
1168 1088 - 1152 94000 1.7 2.7 12900 2.4 3.8
No Cross Talk
Cross Talk (49 adjacent CAP pairs)
26 AWG (0.4mm)24 AWG (0.5mm)
26 AWG (0.4mm)24 AWG (0.5mm)
Transmission Distance - Patton NetLink Model 1089
Copyright © 2006
Patton Electronics Company
All Rights Reserved
Loading...