Patton 1006 User Manual

USER MANUAL
MODEL 1006
DB-9 Async. Short Range Modem with Carrier Sense
An ISO-9001
Certified Company
SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com
1.0 WARRANTY INFORMATION
Patton Electronicswarrants all Model 1006 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above. Under no condition shallPatton Electronicsbe liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product. Patton Electronicsspecifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 1006 generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception. The Model 1006 has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the Model 1006 does cause interference to radio or television reception, which can be determined by turning the power off or removing the card, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).
1.3 SERVICE
All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Service at
telephone: (301) 975-1007,
web address: http://www.patton.com;
email: support@patton.com.
NOTE:Packages received without an RMA number will not be
accepted.
Patton Electronics’ technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 1006. Technical Service hours: 8AM to 5PM EST, Monday
through Friday.
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility (EMC) directive and the Low Voltage Directive (LVD) of the Union European (EU). A Certificate of Compliance is available by contacting Patton Technical Support.
1
2
2.0 GENERAL INFORMATION
3.0 INSTALLATION
Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Year parts and labor. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics Technical Support at (301) 975-1007.
2.1 FEATURES
• Ideal for UNIX operating systems
• Range to 17 miles (27.2 km)
• Data rates to 19,200 bps
• No AC power or batteries required
• Carrier sense handshaking
• Useful for troubleshooting or monitoring a line
• Very thin case for closely spaced computer ports
• Available with RJ-11, RJ-45 or terminal block with strain relief
• Connects directly to the RS-232 port via DB-9 connector
• Surge protection (Model 1006S only)
• Made in USA
2.2 DESCRIPTION
The Patton Model 1006Carrier Sense Short Range Modem
allows RS-232 UNIX systems to communicate up to 17 miles (27.2 km) over two unconditioned twisted pair cable. Supporting data rates to
19.2 Kbps, the Model 1006 requires no AC power or batteries.
The Model 1006 has a special carrier sense feature, which automatically detects the presence of a carrier on the line. This is useful in UNIX environments, where the host must see a carrier before it will send a logon screen to the terminal. The carrier sense feature also plays an important role in troubleshooting, where the presence or absence of a carrier indicates the validity of your line connection.
Measuring only 2.5” x 1.2” x .75” (6.4 x 3.0 x 1.9 cm), the Model 1006 is housed in a pop-open ABS plastic case. The Model 1006 comes with a male or female DB-9 connector and a choice of interfaces (RJ-11 jack, RJ-45 jack or terminal blocks with strain relief). For surge handling capability, the Model 1006S is compliant with IEC 801.5 level 2, 1kV.
The Model 1006 is easy to install. This section tells you how to properly connect the Model 1006 to the twisted pair and RS-232 interfaces, and how to operate the Model 1006.
3.1 CONNECTION TO THE TWISTED PAIR INTERFACE
The Model 1006 supports carrier sense handshaking between two DB-9 RS-232 devices at distances to 17 miles (27.2 km) and data rates to 19.2 Kbps. There are two requirements for installing the Model 1006:
1. These units work in pairs. Therefore, you must have one Model 1006 at each end of a two twisted pair interface.
2. To function properly, the Model 1006 needs two twisted pairs of metallic wire. The pairs must be unconditioned, dry metallic wire, between 19 and 26 AWG (the higher number gauges may limit distance). Standard dial-up telephone circuits, or leased circuits that run through signal equalization equipment are not acceptable.
For your convenience, the Model 1006 is available with three
different twisted pair interfaces: RJ-11 jack, RJ-45 jack and terminal blocks with strain relief.
3.1.1 TWISTED PAIR CONNECTION USING RJ-11 OR RJ-45
The RJ-11 and RJ-45 connectors on the Model 1006's twisted pair
interface are pre-wired for a standard TELCO wiring environment (see Figure 1). The tables on the following page show the signal/pin relationships:
1 - Blue 2 - Yellow 3 - Green 4 - Red 5 - Black 6 - White
Figure 1. AT&T standard modular color codes
1 - Blue 2 - Orange 3 - Black 4 - Red 5 - Green 6 - Yellow 7 - Brown 8 - Slate
3 4
+ 5 hidden pages