Patmont Motor Werks HoverBoard II, Stealth II User Manual

MAINTENANCE / PARTS

• All frame and engine parts are available through your authorized Go-Ped®

reseller or the Go-Ped® website at www.goped.com. At Goped.com, you’ll be
able to locate a dealer near you as well as shop for parts for your Goped.

• Use only manufacturer’s original equipment, replacement parts when servicing

this unit. These parts are available from your authorized dealer . The use of non­standard parts, or other accessories or attachments not designed for this unit
could result in serious injury to the user or damage to the unit.

Although the engine noise is virtually non-existent, it is difficult to hear vehicles
approaching you. Be aware of your surroundings before changing direction. The
Hoverboard® and Stealth® have been designed to operate on any hard-packed,
dry and smooth surfaces.

· Avoid wet and/or oily surfaces, loose sand, gravel, potholes, etc.

· Always use both hands while riding.

Y our Go-Ped®, although environmentally-friendly , is not grade-friendly . Depending
on the weight of the rider, it will not ascend certain grades, and is not designed for
descending grades in excess of 5%.

SAFETY WARNING

Do not wear loose-fitting clothes or articles such as scarves, strings, chains,
ties, etc. Do not remove rear-fender which guards drive mechanism from

foreign objects.

Technical Support Line [phone]

Email – [e-mail] or on the Internet at www.goped.com
Go-Ped® is a registered trademark of PMW.
© 1998 PMW All rights reserved

SUPPORT

DRIVING DEFENSIVELY

WARNING

The status of your Go-Ped®, as a motor vehicle, is subject to drivers’
license, insurance requirements and registration, which varies state­to-state. Please contact your local, law enforcement agency or
Department of Motor Vehicles for further advisement on these

HOVERBOARD / STEALTH GO-PED®s SPECIFICATIONS

* Speeds and Running Durations vary significantly depending on the weight of
the rider and conditions of road surface, grade and weather.

IMPORTANT! If you did not completely fill out and submit a warranty
registration form to your dealer upon purchasing your Go-Ped® product,
return to your dealer immediately and do so. If your form is not turned into

the manufacturer, YOU DO NOT HAVE A WARRANTY.

Pay EXTRA A TTENTION to the yellow , SAFETY W ARNING sections of this
manual. These are very important to understand before you ride your Go­Ped®.BE SURE TO READ THESE INSTRUCTIONS CAREFULLY

BEFORE ATTEMPTING T O START OR OPERATE THIS UNIT.

FREQUENTLY ASKED QUESTIONS / TROUBLESHOOTING

Question: How far does my Electric Go-Ped go?

• Approximately 7-12 miles. This depends on rider weight & riding
conditions i.e. smooth/ rough surface, wind & grade (hills).

Question: How long does my Electric Go-Ped take to charge?

• 3 to 4 hours

Question: Is it legal to ride on public roads or sidewalks?

• Please consult your local Law Enforcement Agencies.

Question: Is there a seat for the Hoverboard / Stealth?

• Y es, the Sat Squatch Seat which work on all Go Ped models. Visit

www.Goped.com for more information

Question: What is the maximum weight capacity of the Hoverboard /

Stealth?

• 250 pounds; to prevent overheating of the motor.

Question: Is it okay to completly discharge the batteries?

• No, these Lead-Acid Batteries do not retain memory & should be topped
off before every ride. Fully discharging them will render them useless.

Question: How many times can I charge my Electric Go-Ped?

• The Sealed Lead Acid Batteries have a life-cycle of approximately 300
charges.

Question: My Go-Key® doesn’t light up! What could be wrong?

• *The battery connections might have become loose.

• *Fuse on the control board might been damaged.

Question: Key is luminated, but Go-Ped doesn’t work.

• Remove the Go-Key for a minimum of 30 seconds then place back in.

• Check front brake lever. A partially engaged brake or improper alignment
of the brake sensor will engage the engine brake system.

Question: Diminished range, will not hold a charge?

• The batteries have been over-discharged or not charged enough. One or
more batteries may need to be replaced.

• Battery abuse, such as too heavy of a load and too steep of a incline will
cause premature Battery failure.

• *Battery connection might have become loose.

• *Battery voltage should be in the range of 6.2 volt to 6.7 volt.

• *Batteries should be Load T ested to ensure full Amperage (3amp)

Question: Why does my Go-Key dim when I engage throttle?

• Dead Battery(ies)

• *Remove deck and check Battery wires for loose connections.

Question: Charger light does not come on?

• *Check the 3.15 amp glass fuse on the Charger Board.

• *Check (3) spade connectors on A/C Socket Plug.

Question: Motor overheats and shuts off?

• Exceeding Maximum weight.

• T oo steep of incline (grade).

• Pumping the throttle lever with Go-Key inserted

• Remove the Go-Key for a minimum of 30 seconds then place back in.

• T oo much Motor spring pressure.

Question: I need to buy parts for my Go-Ped, where should I go?

• T o find your nearest Go-Ped® Dealer , please go to www.Goped.com and
click on “find-a-dealer”. An alternative would be the Go-Shop section
located on Goped.com

*Work must be done by a Go-Ped technician for repairs. Performing any of the

procedures will void your warranty. Goto www.Goped.com to find you nearest local
dealer for technical help.